Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM › from 2019.08
RM2850E _57 Power Source / Network _073263 CAN COMMUNICATION _0356688 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  Combination Meter ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Combination Meter ECU Communication Stop Mode Either condition is met:
·

Communication stop for "Combination Meter" is indicated on the "Communication Bus Check" screen of the GTS (Click here(Click here)).

·

Communication stop history for "Combination Meter" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Combination Meter" is 6 or more.) (Click here(Click here))

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Combination Meter ECU Communication Stop Mode" in "DTC Combination Table" (Click here(Click here)).


·

Combination meter assembly CAN main wire or connector

·

Power source circuit of combination meter assembly

·

Combination meter assembly ground circuit

·

Combination meter assembly



WIRING DIAGRAM

C339057E15
1.656,0.927 2.885,1.125 1.229,0.198 10 false 2 1.667,1.521 2.896,1.719 1.229,0.198 10 false 13 0.302,2 1.531,2.198 1.229,0.198 10 false J91*1, J76*2 0.292,2.198 2.104,2.563 1.813,0.365 10 false No. 63 Junction Connector*1, No. 68 Junction Connector*2 1.667,3.313 4.573,3.51 2.906,0.198 10 false from IG2-NO.2 Relay 2.167,2.5 5.073,2.698 2.906,0.198 10 false from Battery 3.927,3.188 5.302,3.385 1.375,0.198 10 false METER-IG2 4.104,2.344 5.479,2.542 1.375,0.198 10 false DOME 5.573,0.938 6.948,1.135 1.375,0.198 10 false CANH 5.573,1.708 6.948,1.906 1.375,0.198 10 false CANL 5.583,2.521 6.958,2.719 1.375,0.198 10 false B 5.583,3.333 6.958,3.531 1.375,0.198 10 false IG+ 5.583,4.167 6.958,4.365 1.375,0.198 10 false ES 5.115,4.802 5.427,5 0.313,0.198 10 false J1 5.104,4.969 7.01,5.25 1.906,0.281 10 false Combination Meter Assembly 0.271,4.667 1.958,4.865 1.688,0.198 10 false *1: for LHD 0.281,5 1.969,5.198 1.688,0.198 10 false *2: for RHD 5.313,0.927 5.625,1.125 0.313,0.198 10 false 23 5.323,1.51 5.635,1.708 0.313,0.198 10 false 22 5.375,2.417 5.688,2.615 0.313,0.198 10 false 1 5.385,3.25 5.698,3.448 0.313,0.198 10 false 2 5.323,4.052 5.635,4.25 0.313,0.198 10 false 21

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY CAN MAIN WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the combination meter assembly connector.


c.
C358908E02
1.5,0.333 1.865,0.573 0.365,0.24 0.625,1.802 0.771,1.802 0.771,1.802 0.771,1.281 true 1.052,1.802 0.896,1.802 0.896,1.802 0.896,1.281 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 0.219,1.729 0.833,1.927 0.615,0.198 10 false CANL 1.115,1.719 1.729,1.917 0.615,0.198 10 false CANH 1.604,0.375 1.917,0.573 0.313,0.198 10 false J1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-23 (CANH) - J1-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Connect the cable to the negative (-) battery terminal.


b.
C358908E03
1.479,0.115 1.844,0.365 0.365,0.25 0.656,1.073 0.656,0.375 0.656,0.375 0.51,0.375 true 0.781,1.073 0.781,0.375 0.781,0.375 0.906,0.375 true 0.667,1.292 0.667,1.917 0.667,1.917 0.802,1.917 true 0.104,0.052 0.417,0.25 0.313,0.198 10 false *a 1.594,0.146 1.906,0.344 0.313,0.198 10 false J1 0.375,0.313 0.531,0.51 0.156,0.198 10 false B 0.979,0.302 1.438,0.5 0.458,0.198 10 false IG+ 0.865,1.833 1.177,2.031 0.313,0.198 10 false ES

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J1-1 (B) - Body ground Always 11 to 14 V
J1-2 (IG+) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-21 (ES) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)

Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR