Home › Engine / Hybrid System › 2TR-FE (LUBRICATION) › OIL AND OIL FILTER › 2019.08–2021.01
RM2850E _51 Engine / Hybrid System _073292 2TR-FE LUBRICATION _0356999 OIL AND OIL FILTER A

2TR-FE LUBRICATION  OIL AND OIL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
·

Prolonged and repeated contact with engine oil will cause removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

·

Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Wear protective clothing and gloves. Wash your skin thoroughly with soap and water, or use a waterless hand cleaner to remove any used engine oil. Do not use gasoline, thinners or solvents.

·

For environmental protection, used oil and used oil filters must be disposed of at designated disposal sites.



PROCEDURE

Hide 58410 1.REMOVE ENGINE SERVICE HOLE COVER

Hide 58734B 2.REMOVE REAR ENGINE SERVICE COVER WEATHERSTRIP

Hide 58521D 3.REMOVE ENGINE SERVICE HOLE COVER MAT

Hide 58420 4.REMOVE NO. 2 ENGINE SERVICE HOLE COVER ASSEMBLY

Hide 5.DRAIN ENGINE OIL

a.

Remove the oil filler cap.


b.

Remove the oil drain plug and drain the oil into a container.


c.

Clean and install the oil drain plug with a new gasket.

Torque:

38 N*m (382 kgf*cm, 28 ft.*lbf)



Hide 15601 6.REMOVE OIL FILTER SUB-ASSEMBLY

a.
A177806

Using SST, remove the oil filter.


Hide 15601 7.INSTALL OIL FILTER SUB-ASSEMBLY

a.

Check and clean the oil filter installation surface.


b.

Apply clean engine oil to the gasket of a new oil filter.


c.

Lightly screw the oil filter into place by hand. Tighten it until the gasket contacts the seat.


d.
A177807

Using SST, tighten the oil filter.

i.

Depending on the work space available, choose from the following.

If enough space is available, use a torque wrench to tighten the oil filter.

Torque:

17 N*m (175 kgf*cm, 13 ft.*lbf)


If enough space is not available to use a torque wrench, tighten the oil filter a 3/4 turn by hand or use a common wrench.



Hide 8.ADD ENGINE OIL

a.

Add fresh engine oil.

Engine oil:
Oil Grade Oil Viscosity (SAE)
API grade SL "energy-conserving", SM "energy-conserving", SN "resource-conserving", SN PLUS "resource-conserving" or ILSAC multigrade engine oil
·

5W-30

·

10W-30


API grade SL, SM, SN or SN PLUS multigrade engine oil
·

15W-40

·

20W-50




Standard capacity:
Item Specified Condition
Drain and refill with oil filter change 6.0 liters (6.3 US qts, 5.3 Imp. qts)
Drain and refill without oil filter change 5.4 liters (5.7 US qts, 4.8 Imp. qts)
Dry fill 6.3 liters (6.7 US qts, 5.5 Imp. qts)



b.

Install the oil filler cap.


Hide 9.INSPECT FOR ENGINE OIL LEAK

a.

Start the engine, and check that there are no oil leaks after performing maintenance.


Hide 58420 10.INSTALL NO. 2 ENGINE SERVICE HOLE COVER ASSEMBLY

Hide 58521D 11.INSTALL ENGINE SERVICE HOLE COVER MAT

Hide 58734B 12.INSTALL REAR ENGINE SERVICE COVER WEATHERSTRIP

Hide 58410 13.INSTALL ENGINE SERVICE HOLE COVER