Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P146F  Particulate Matter Sensor Supply Voltage Circuit High  P24D0  Particulate Matter Sensor Supply Voltage Circuit Low  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P146F Particulate Matter Sensor Supply Voltage Circuit High Diagnosis Condition:
·

The PM sensor is in operation.

·

Battery voltage is in the range of 10 V to 16 V

·

The ignition switch is ON for 5 seconds or more (the starter is not actuated).


Malfunction Status:

When the supply voltage to the particulate matter sensor is above 16 V, Abnormality is determined by the error dialog of the particulate matter sensor.


Malfunction Duration:

-


·

Particulate matter sensor

·

Battery

·

Particulate matter sensor power supply circuit


Class C DTC stored
P24D0 Particulate Matter Sensor Supply Voltage Circuit Low Diagnosis Condition:
·

The PM sensor is in operation.

·

Battery voltage is in the range of 10 V to 16 V

·

The ignition switch is ON for 5 seconds or more (the starter is not actuated).


Malfunction Status:

When the supply voltage to the particulate matter sensor is below 10.5 V, Abnormality is determined by the error dialog of the particulate matter sensor.


Malfunction Duration:

-


·

Particulate matter sensor

·

Battery

·

Particulate matter sensor power supply circuit


Class C DTC stored

MONITOR DESCRIPTION

Abnormality in the particulate matter sensor supply voltage is detected by the self-diagnosis function of the particulate matter sensor.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P146F
P24D0
Ignition switch ON

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P146F or P24D0 is output A
DTC P146F or P24D0 and other DTCs are output B




A

2.CHECK PARTICULATE MATTER SENSOR (POWER SOURCE CIRCUIT)

B

2.CHECK PARTICULATE MATTER SENSOR (POWER SOURCE CIRCUIT)
a.
A452679C01
1.469,0.198 1.948,0.531 0.479,0.333 1.083,1.833 1.458,1.479 true 2.625,1.802 2.24,1.469 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.583,0.292 2.583,0.594 1,0.302 10 false P15 2.5,1.854 2.958,2.052 0.458,0.198 10 false GND 0.75,1.854 1.292,2.052 0.542,0.198 10 false PWR
*a Front view of wire harness connector
(to Particulate Matter Sensor)


Disconnect the particulate matter sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
P15-2 (PWR) - P15-5 (GND) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK DTC OUTPUT

NG

6.INSPECT BATTERY VOLTAGE
3.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Turn the ignition switch to ON and turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Read Current DTCs.

Result:
Result Proceed to
DTC P146F or P24D0 is output A
DTCs are not output B




A

4.REPLACE PARTICULATE MATTER SENSOR

B

END

4.REPLACE PARTICULATE MATTER SENSOR

Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Turn the ignition switch to ON and turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

6.INSPECT BATTERY VOLTAGE
a.

Turn the ignition switch off.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Positive (+) terminal - Negative (-) terminal Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS OR CONNECTOR (PARTICULATE MATTER SENSOR - BODY GROUND)

NG

10.CHARGE OR REPLACE BATTERY
7.CHECK HARNESS OR CONNECTOR (PARTICULATE MATTER SENSOR - BODY GROUND)
a.
A452679C03
1.469,0.198 1.948,0.531 0.479,0.333 2.625,1.802 2.24,1.469 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.583,0.292 2.583,0.594 1,0.302 10 false P15 2.5,1.854 2.958,2.052 0.458,0.198 10 false GND
*a Front view of wire harness connector
(to Particulate Matter Sensor)


Disconnect the particulate matter sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P15-5 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR (PARTICULATE MATTER SENSOR - BODY GROUND)
8.REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

3.CHECK DTC OUTPUT
9.REPAIR OR REPLACE HARNESS OR CONNECTOR (PARTICULATE MATTER SENSOR - BODY GROUND)
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

3.CHECK DTC OUTPUT
10.CHARGE OR REPLACE BATTERY
a.

Charge or replace the battery.


Result:
Proceed to
NEXT



NEXT

3.CHECK DTC OUTPUT