Home › Engine / Hybrid System › N04C-VJ (ENGINE CONTROL) › ECD SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _096807 N04C-VJ ENGINE CONTROL _0454116 ECD SYSTEM U

N04C-VJ ENGINE CONTROL  ECD SYSTEM  DATA LIST / ACTIVE TEST  


READ DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are for reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

Read the Data List.

Tester Display Measurement Item/Range Normal Condition Diagnostic Notes
Vehicle Speed Vehicle speed:
Min.: 0 km/h, Max.: 255 km/h
Actual vehicle speed Speed indicated on speedometer
Target Idle Engine Speed Target idle engine speed:
Min.: 0 rpm, Max.: 10000 rpm
Idling: 600 rpm
Ignition switch ON (after engine warm-up, air conditioning off, neutral)
-
Engine Speed Engine speed:
Min.: 0 rpm, Max.: 16383 rpm
IG ON : 0 rpm After warming-up engine
Calculate Load Calculated load by ECM:
Min.: 0%, Max.: 100%
Idling: 10 to 20%
Idling (air conditioning off, neutral)
-
MAF Air flow rate from mass air flow meter sub-assembly:
Min.: 0 gm/s, Max.: 655.35 gm/s
Idling: 4.0 to 15.0 gm/s
Running without load (3000 rpm): 80 to 90 gm/s
MAF indicates the output value of the mass air flow meter sub-assembly.
Atmosphere Pressure Atmospheric pressure value:
Min.: 0 kPa (0 mmHg, 0 in.Hg), Max.: 255 kPa (1912.6 mmHg, 75.3 in.Hg)
Actual atmospheric pressure Atmospheric Pressure indicates the output value of the atmospheric pressure sensor built into the ECM.
MAP Absolute pressure inside intake manifold:
Min.: 0 kPa, Max.: 255 kPa
Idling: 95 to 105 kPa or less MAP indicates the output value of the turbo pressure sensor.
Coolant Temp Engine coolant temperature:
Min.: -40°C, Max.: 140°C
Gradually increases: Cold start → After engine warm-up Coolant Temp indicates the output value of the water temperature sender gauge assembly.
Intake Air Intake air temperature:
Min.: -40°C, Max.: 140°C
Equivalent to temperature at intake manifold Intake Air indicates the output value of the intake air temperature sensor built into the mass air flow meter sub-assembly.
Intake Air Temp (Turbo) Intake air temperature (Turbo):
Min.: -40°C to 190°C
85°C or less Intake Air Temp (Turbo) indicates the output value of the intake air temperature switch.
Engine Run Time Engine run time:
Min.: 0 s Max.: 65535 s
Time after engine started Service data
Initial Engine Coolant Temp Initial engine coolant temperature:
Min.: -40°C, Max.: 120°C
Engine coolant temperature when engine starts -
Initial Intake Air Temp Initial intake air temperature:
Min.: -40°C, Max.: 120°C
Intake air temperature when engine starts -
Battery Voltage Battery voltage:
Min.: 0 V Max.: 65.5 V
Idling: 11 to 14 V -
Accel Position Accelerator position status:
Min.: 0%, Max.: 100%
Accelerator pedal released: 0% -
Accel Sens. No. 1 Volt % Accelerator position No. 1:
Min.: 0%, Max.: 100%
·

Accelerator pedal released: 12 to 20%

·

Accelerator pedal depressed: 60 to 78%


-
Accel Sens. No. 2 Volt % Accelerator position No. 2:
Min.: 0%, Max.: 100%
·

Accelerator pedal released: 28 to 36%

·

Accelerator pedal depressed: 72 to 92%


-
Accel Sensor Out No. 1 Accelerator position No. 1 voltage:
Min.: 0 V, Max.: 5 V
·

0.6 to 1.0 V: Accelerator pedal released

·

3.0 to 3.9 V: Accelerator pedal fully depressed


Read value with ignition switch ON (Do not start engine)
Accel Sensor Out No. 2 Accelerator position No. 2 voltage:
Min.: 0 V, Max.: 5 V
·

1.4 to 1.8 V: Accelerator pedal released

·

3.8 to 4.6 V: Accelerator pedal fully depressed


Read value with ignition switch ON (Do not start engine)
Target Throttle Position Diesel throttle angle:
Min.: -0%, Max.: 100%
Idling after warmed-up engine: 75 to 92% Target Throttle Position indicates the value calculated by the ECM.
Actual Throttle Position Diesel throttle angle:
Min.: -0%, Max.: 100%
Idling after warmed-up engine: 75 to 92% Actual Throttle Position indicates the actual position of the diesel throttle valve.
Throttle Close Learning Val. Throttle valve fully closed:
Min.: 0 deg, Max.: 84 deg
12 to 22 deg -
Diesel Throttle Learn Status Diesel throttle learning status:
OK or NG
OK -
Throttle Sensor Volt % Throttle actuator output :
Min.: 0%, Max.: 100%
IG ON : 60 to 80%
Throttle Motor DUTY Throttle actuator output :
Min.: 0%, Max.: 100%
- When start requests to open the diesel throttle valve increase, the throttle motor output value increases.
Injection Volume Injection volume:
Min.: 0 mm3/st, Max.: 1279.98 mm3/st
Idling: 5.0 to 12.0 mm3/st -
Inj. FB Vol. for Idle Idle stable control:
Min.: -80 mm3/st, Max.: 79.99 mm3/st
-5 to 5 mm3/st Inj. FB Vol. for Idle is calculated by the ECM and is reflected during idling.
Inj Vol Feedback Learning Injection volume feedback learning value:
Min.: -10 mm3/st, Max.: 9.9 mm3/st
- -
Injection Feedback Val #1 Injection volume correction for cylinder 1:
Min.: -10 mm3/st, Max.: 10 mm3/st
Idling: -7.0 to 7.0 mm3/st -
Injection Feedback Val #2 Injection volume correction for cylinder 2:
Min.: -10 mm3/st, Max.: 10 mm3/st
Idling: -7.0 to 7.0 mm3/st -
Injection Feedback Val #3 Injection volume correction for cylinder 3:
Min.: -10 mm3/st, Max.: 10 mm3/st
Idling: -7.0 to 7.0 mm3/st -
Injection Feedback Val #4 Injection volume correction for cylinder 4:
Min.: -10 mm3/st, Max.: 10 mm3/st
Idling: -7.0 to 7.0 mm3/st -
Pilot 1 Injection Period Pilot 1 Injection period:
Min.: 0 μs, Max.: 65535 μs
Idling after warming up engine: 0 to 500 μs -
Pilot 2 Injection Period Pilot 1 Injection period:
Min.: 0 μs, Max.: 65535 μs
Idling: 0 to 600 μs -
Main Injection Period Main Injection Period
Min.: 0 μs, Max.: 65535 μs
Idling: 500 to 1000 μs -
After Injection Period After Injection period:
Min.: 0 μs, Max.: 65535 μs
- -
Pilot 1 Injection Timing Pilot 1 Injection timing:
Min.: -70°CA, Max.: 20°CA
Idling: -10 to -8°CA -
Pilot 2 Injection Timing Pilot 2 Injection timing:
Min.: -50°CA, Max.: 20°CA
Idling: -5 to -3°CA -
Main Injection Timing Main Injection timing:
Min.: -90°CA, Max.: 90°CA
Idling: 0 to 2°CA -
After Injection Timing After Injection timing:
Min.: -10°CA, Max.: 50°CA
- -
Injector Memory Error Injector Memory Error:
No Error or Error
No Error If the ID code has not yet been input in a new ECM, or if an ID code from another injector assembly or an ID code outside of the setting range is input in a new ECM, DTC P062F is output and an EEPROM error (QR code) is displayed.
Injection Pressure Correction Injection pressure correction:
Min.: -500 mm3/st, Max.: 780 mm3/st
-400 to 400 mm3/st -
Target Common Rail Pressure Target common rail pressure:
Min.: 0 kPa, Max.: 655350 kPa
Idling: 20000 to 200000 kPa -
Fuel Press Fuel pressure:
Min.: 0 kPa, Max.: 655350 kPa
Idling: 20000 to 30000 kPa -
Common Rail Pres Sens 2 Common Rail Pres Sens 2:
Min.: 0 kPa, Max.: 655350 kPa
Idling: 20000 to 30000 kPa Backup of the output value from the fuel pressure sensor (built into common rail assembly).
Fuel Temperature Fuel temperature:
Min.: -40°C, Max.: 215°C
Idling after warmed-up engine: 20 to 60°C Fuel temperature indicates the output value of the fuel temperature sensor.
Fuel Return Temp Fuel return temperature:
Min.: -40°C, Max.: 215°C
Idling after warmed-up engine: 35 to 130°C Fuel return temperature indicates the value calculated by the ECM.
Target Pump SCV Current Pump open current value:
Min.: 0 mA, Max.: 4000 mA
Idling after warmed-up engine: 1350 to 2200 mA -
Pump SCV Learning Value Pump open current value:
Min.: -4096 mA, Max.: 4095.8 mA
-100 to 100 mA -
AF Lambda B1S1 Lambda equivalent ratio:
Min.: 0, Max.: 1.99
- -
AFS Voltage B1S1 AFS Voltage B1S1 value:
Min.: 0 V, Max.: 7.99 V
- -
Target EGR Position Target EGR position:
Min.: 0%, Max.: 100%
Idling: 50 to 70% -
EGR Initial Step Position EGR initial step position:
Min.: 0, Max.: 255 step
- -
Actual EGR Valve Pos. Actual EGR Valve position:
Min.: 0%, Max.: 99.6%
Idling: 40 to 70 % -
EGR Close Lrn. Val. EGR close learning value:
Min.: 0 V, Max.: 5 V
3.5 to 4.5 V -
EGR Operation Prohibit EGR operation prohibit:
OK or NG
OK -
Target Booster Pressure Target boost pressure:
Min.: 0 kPa Max.: 2047.96 kPa
Idling after warning up engine and vehicle is under normal atmospheric pressure: 90 to 110 kPa -
Boost Pressure Deviation Boost pressure deviation:
Min.: -320 kPa, Max.: 320 kPa
- -
VN Turbo Command VN turbo command:
Min.: -128%, Max.: 127%
- -
Actual VN Position Actual VN turbo position:
Min.: -128%, Max.: 127%
- -
VN Turbo Type VN turbo type:
Not Avl, Commo, Vacuum, CAN Com or DC
CAN Com -
VN Turbo Max Angle VN turbo maximum angle :
Min.: 0%, Max.: 100%
100% -
VN Turbo Min Angle VN turbo minimum angle :
Min.: 0%, Max.: 100%
7.5% -
VN Turbo Operation Prohibit VN turbocharger operation prohibition:
ON or NG
- -
Exhaust Temperature B1S1 Exhaust temperature sensor for sensor 1 (upstream):
Min.: 0°C, Max.: 1000°C
- If 0°C (32°F), sensor circuit is open
If 1000°C (1832°F) or more, sensor circuit is shorted
Exhaust Temperature B1S2 Exhaust temperature sensor for sensor 2 (downstream):
Min.: 0°C, Max.: 1000°C
- If 0°C (32°F), sensor circuit is open
If 1000°C (1832°F) or more, sensor circuit is shorted
Exhaust Temperature B1S3 Exhaust temperature sensor for sensor 3 (downstream): - If 0°C (32°F), sensor circuit is open
If 1000°C (1832°F) or more, sensor circuit is shorted
Exhaust Temperature B1S4 Exhaust temperature sensor for sensor 4 (downstream): - If 0°C (32°F), sensor circuit is open
If 1000°C (1832°F) or more, sensor circuit is shorted
DPF Differential Pressure DPF differential pressure:
Min.: -5 kPa, Max.: 100 kPa
-3 kPa to 3 kPa -
NOx Density B1S1 Min.: 0 ppm, Max.: 65535 ppm - -
NOx Density B1S1 Supported Unsupp or Supp Supp
·

Supp: The item is supported by the vehicle.

·

Unsupp: The monitor is not supported by the vehicle.


Catalyst Differential Press Amount of clogging in catalyst:
Min.: -3.9998, Max.: 3.9998
- -
Diff. Press. Sensor Corr. Differential pressure correction:
Min.: -10 kPa, Max.: 246 kPa
Idling: -1.5 to 1.5 kPa -
Exhaust Fuel Addition FB Exhaust fuel addition FB
Min.: -256, Max.: 255.99
- -
DPF PM Block DPF particulate matter (PM) Block:
No Block or Blocked
No Block -
Add. INJ Flow Excessive Abnormal drop in actual air-fuel ratio:
OK or NG
OK -
DPF Overtemperature DPR catalyst overheating:
OK or NG
OK -
DPNR/DPF Status Reju (PM) Result of DPF catalyst regeneration (PM):
Standby, Ready, Operate or Compl
Operate: DPF catalyst regeneration operate -
PM Accumulation Ratio PM Accumulation ratio:
Min.: 0%, Max.: 510%
- -
Catalyst Regeneration Switch DPF switch status:
ON or OFF
ON: DPF switch on -
Exhaust Brake Switch Exhaust brake switch status:
ON or OFF
ON: Exhaust brake operated -
Starter Signal Starter signal:
ON or OFF
ON: Cranking -
IG SW Ignition switch status:
ON or OFF
Ignition switch ON: ON
Ignition switch off: OFF
-
Neutral Position SW Signal Park/neutral position switch status for automatic transmission:
ON or OFF
ON: Shift lever in P or N for Automatic Transmission
Stop Light Switch Stop light switch status:
ON or OFF
·

ON: Brake pedal depressed

·

OFF: Brake pedal released


-
A/C Signal Air conditioning signal:
ON or OFF
ON: Air conditioning operate -
Check Mode Check mode:
ON or OFF
ON: Check mode on Click here(Click here)
Complete Parts Monitor Comprehensive component monitor:
Not Avl or Avail
-
·

Not Avl: The monitor is not available on the vehicle.

·

Avail: The monitor is available on the vehicle.


Fuel System Monitor Fuel system monitor:
Not Avl or Avail
-
·

Not Avl: The monitor is not available on the vehicle.

·

Avail: The monitor is available on the vehicle.


Misfire Monitor Misfire monitor:
Not Avl or Avail
-
·

Not Avl: The monitor is not available on the vehicle.

·

Avail: The monitor is available on the vehicle.


EGR/VVT Monitor EGR/VVT monitor:
Not Avl or Avail
-
·

Not Avl: The monitor is not available on the vehicle.

·

Avail: The monitor is available on the vehicle.


EGR/VVT Monitor EGR/VVT monitor:
Compl or Incmpl
- Compl / Incmpl:
The item changes from Incmpl to Compl if the monitor was completed at least once at some time in the past.
This item does not change when the ignition switch is turned off. However, the item changes back to Incmpl when DTCs are cleared or the battery cable is disconnected.
O2S(A/FS) Heater Monitor O2S(A/FS) Heater Monitor:
Not Avl or Avail
-
·

Not Avl: The monitor is not available on the vehicle.

·

Avail: The monitor is available on the vehicle.


O2S(A/FS) Heater Monitor O2S(A/FS) Heater Monitor:
Compl or Incmpl
- Compl / Incmpl:
The item changes from Incmpl to Compl if the monitor was completed at least once at some time in the past.
This item does not change when the ignition switch is turned off. However, the item changes back to Incmpl when DTCs are cleared or the battery cable is disconnected.
O2S(A/FS) Monitor O2S(A/FS) Monitor:
Not Avl or Avail
-
·

Not Avl: The monitor is not available on the vehicle.

·

Avail: The monitor is available on the vehicle.


O2S(A/FS) Monitor O2S(A/FS) Monitor:
Compl or Incmpl
- Compl / Incmpl:
The item changes from Incmpl to Compl if the monitor was completed at least once at some time in the past.
This item does not change when the ignition switch is turned off. However, the item changes back to Incmpl when DTCs are cleared or the battery cable is disconnected.
A/C Monitor A/C monitor
Not Avl or Avail
-
·

Not Avl: The monitor is not available on the vehicle.

·

Avail: The monitor is available on the vehicle.


A/C Monitor A/C monitor
Compl or Incmpl
- Compl / Incmpl:
The item changes from Incmpl to Compl if the monitor was completed at least once at some time in the past.
This item does not change when the ignition switch is turned off. However, the item changes back to Incmpl when DTCs are cleared or the battery cable is disconnected.
2nd Air Monitor 2nd air monitor
Not Avl or Avail
-
·

Not Avl: The monitor is not available on the vehicle.

·

Avail: The monitor is available on the vehicle.


2nd Air Monitor 2nd air monitor
Compl or Incmpl
- Compl / Incmpl:
The item changes from Incmpl to Compl if the monitor was completed at least once at some time in the past.
This item does not change when the ignition switch is turned off. However, the item changes back to Incmpl when DTCs are cleared or the battery cable is disconnected.
EVAP Monitor EVAP monitor
Not Avl or Avail
-
·

Not Avl: The monitor is not available on the vehicle.

·

Avail: The monitor is available on the vehicle.


EVAP Monitor EVAP monitor
Compl or Incmpl
- Compl / Incmpl:
The item changes from Incmpl to Compl if the monitor was completed at least once at some time in the past.
This item does not change when the ignition switch is turned off. However, the item changes back to Incmpl when DTCs are cleared or the battery cable is disconnected.
Heated Catalyst Monitor Heated catalyst monitor
Not Avl or Avail
-
·

Not Avl: The monitor is not available on the vehicle.

·

Avail: The monitor is available on the vehicle.


Heated Catalyst Monitor Heated catalyst monitor
Compl or Incmpl
- Compl / Incmpl:
The item changes from Incmpl to Compl if the monitor was completed at least once at some time in the past.
This item does not change when the ignition switch is turned off. However, the item changes back to Incmpl when DTCs are cleared or the battery cable is disconnected.
Catalyst Monitor Catalyst monitor
Not Avl or Avail
-
·

Not Avl: The monitor is not available on the vehicle.

·

Avail: The monitor is available on the vehicle.


Catalyst Monitor Catalyst monitor
Compl or Incmpl
- Compl / Incmpl:
The item changes from Incmpl to Compl if the monitor was completed at least once at some time in the past.
This item does not change when the ignition switch is turned off. However, the item changes back to Incmpl when DTCs are cleared or the battery cable is disconnected.
# Codes(Include History) Number of codes:
Min.: 0, Max.: 255
- Number of detected DTCs
MIL MIL status:
ON or OFF
ON: MIL ON -
Time after DTC Cleared Time after DTC cleared:
Min.: 0 min, Max.: 65535 min
Equivalent to time after DTCs were erased -
Distance from DTC Cleared Distance after DTC cleared:
Min.: 0 km, Max.: 65535 km
Equivalent to drive distance after DTCs were erased -
Warmup Cycle Cleared DTC Warm up cycle after DTC cleared:
Min.: 0 Max.: 255
- Number of warm up cycles after DTC cleared
TC and TE1 TC and TE1 terminal of DLC3:
ON or OFF
- -
Engine Start Time Engine start time
Min.: 0 ms, Max.: 267000 ms
- -
Engine Speed (Starter Off) Engine speed when starter off
Min.: 0 rpm, Max.: 1593 rpm
- -
Starter Count Starter on count
Min.: 0, Max.: 255
- -
Run Dist of Previous Trip Distance driven during previous trip
Min.: 0 km, Max.: 326 km
- -
Glow Request Lighting Time Glow request lighting time
Min.: 0 ms, Max.: 33423 ms
- -
IG-ON Time Ignition switch ON time before engine start
Min.: 0 ms, Max.: 33423 ms
- -
MAF Low Mass air flow low
OFF or ON
OFF -
Boost Pressure Low Boost pressure low
OFF or ON
OFF -
Common Rail Pressure Low Common rail pressure low
Engine start time
OFF -
Engine Coolant Temp High Engine coolant temperature high
OFF or ON
OFF -
MAF/Estimate MAF Ratio Indicates the ratio of estimated intake air volume and actual intake air volume
Min.: 0, Max.: 2.55
- -
Engine Warm Up Switch Warm up switch status:
ON or OFF
ON: Warm up switch on -
ACT VSV Air conditioning cut signal:
ON or OFF
- -
Target Engine Speed Target engine speed:
Min.: 0 rpm, Max.: 5000 rpm
Idling: 550 to 650 rpm -
Target Common Rail Press Target common rail pressure:
Min.: 0 MPa, Max.: 256 MPa
Idling after warming up engine: 25 to 35 MPa -
Catalyst Warm Up Malfunction Catalyst warm up malfunction:
ON or OFF
OFF -
Manual Catalyst Regeneration Manual catalyst regeneration status:
ON or OFF
OFF -
Pump Mode Supply pump control model:
PCV, DUTY, IG OFF, STOP or Normal
- -
Catalyst Malfunction Catalyst malfunction (differential pressure detection):
ON or OFF
OFF -
Clogged Catalyst Clogged catalyst (differential pressure detection):
ON or OFF
OFF -
Heat Catalyst Catalyst temperature malfunction:
ON or OFF
OFF -
Clogged Catalyst Warning Clogged catalyst warning status
SAFE, Danger or Warning
SAFE -
Catalyst Deteriorate DPF catalyst deteriorate:
ON or OFF
OFF -
Exhaust Fuel Addition Exhaust fuel addition malfunction:
ON or OFF
OFF -
DPF Mode DPF model/
Under, Normal, N/EGR, Warm, Warm/Idl, PM, PM/Idl or S Dchg
Normal -
Injection Pump Learning Status Injection pump learning status:
Compl or Incmpl
Compl -
VN Turbo Valve Position Turbocharger opening value:
Min.: 0% Max.: 100%
- -
PCV Open Duty Suction control valve open duty:
Min.: 0% Max.: 100%
45 to 55% -
PCV Open Current FB Val Suction control valve open current feedback volume:
Min.: -6000 mA, Max.: 6000 mA
-400 to 400 mA -
Engine Overspeed History Engine overspeed history:
ON or OFF
OFF -

HINT:

Normal Condition: If no idling conditions are specified, the shift lever is in the neutral position, and the A/C switch and all accessory switches are off.




PERFORM ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


g.

According to the display on the tester, perform the "Active Test".

Tester Display Test Part Control Range Diagnostic Notes
Control the A/C Cut Signal Control the air conditioning cut signal ON or OFF Test possible when following conditions met:
·

Ignition switch ON

·

Engine stopped


Connect the TC and TE1 Turn on TC and TE1 connection ON or OFF Test possible when following conditions met:
·

Ignition switch ON

·

Engine stopped


Control the EGR Step Position Control the EGR valve step position 0 to 100% Test possible when following conditions met:
·

Confirm that the vehicle is stopped and the engine is idling.


Activate the DPF Rejuvenate (PM) DPF catalyst regeneration (PM) raises temperature of DPF to more than 600°C (1112°F) by adding fuel intermittently ON or OFF Test possible when following conditions met:
·

Warm up the engine

·

Engine idling


Test the Turbo Charger Step Motor Control the turbocharger actuator 40 to 100% Test possible when following conditions met:
·

Engine idling

·

Vehicle stopped

·

Accelerator pedal fully released


Test the Fuel Leak Pressurizes common rail internal fuel pressure, and checks for fuel leaks Stop or Start Test possible when following conditions met:
·

Warm up the engine

·

Engine idling

·

Fuel pressure inside common rail pressurized to specified value and engine speed increased to 2000 rpm when ON is selected

·

Above conditions preserved while test is ON


Active the VN Turbo Open Activate the turbocharger Open or OFF Test possible when following conditions met:
·

Warm up the engine

·

Engine idling


Active the EGR Valve Close Activate the EGR Valve Close or OFF Test possible when following conditions met:
·

Warm up the engine

·

Engine idling

·

Shift lever in neutral


Control the Select Cylinder Fuel Cut Selected cylinder (cylinder #1 to #4) injector fuel cut ON or OFF Fuel injection is stopped while the test is ON.
·

Confirm that the vehicle is stopped and the engine is idling.

·

If the running condition of the engine does not worsen even though injection of the designated cylinder is stopped, the cylinder can be confirmed to be malfunctioning


Activate the VSV for Exhaust Brake Activate the solenoid valve for exhaust brake ON or OFF Test possible when following conditions met:
·

Warm up the engine

·

Engine idling