Home › Engine / Hybrid System › N04C-VJ (ENGINE CONTROL) › ECD SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _096807 N04C-VJ ENGINE CONTROL _0454116 ECD SYSTEM C

N04C-VJ ENGINE CONTROL  ECD SYSTEM  P0115  Engine Coolant Temperature Circuit  P0117  Engine Coolant Temperature Circuit Low Input  P0118  Engine Coolant Temperature Circuit High Input  


DESCRIPTION

A thermistor is built into the Engine Coolant Temperature (ECT) sensor and changes its resistance value according to the ECT.

The structure of the sensor and connection to the ECM are the same as the Intake Air Temperature (IAT) sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0115 Engine Coolant Temperature Circuit Open or short in engine coolant temperature sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Open or short in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM


Comes on DTC stored
P0117 Engine Coolant Temperature Circuit Low Input Short in engine coolant temperature sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Short in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM


Comes on DTC stored
P0118 Engine Coolant Temperature Circuit High Input Open in engine coolant temperature sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Open in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM


Comes on DTC stored

HINT:

When DTC P0115, P0117 and/or P0118 is detected, check the engine coolant temperature by entering the following menus on the tester: Powertrain / Engine and ECT / Data List / Coolant Temp.

Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) Short circuit


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0115
P0117
P0118
Ignition switch ON for 0.5 second or more

WIRING DIAGRAM

A483977E02
5.156,1.573 5.385,1.75 0.229,0.177 10 false 14 5.083,1.771 5.615,1.938 0.531,0.167 10 false B105 5.198,0.958 5.427,1.135 0.229,0.177 10 false 9 5.51,1.667 5.885,1.865 0.375,0.198 10 false E2 5.5,1.052 5.865,1.229 0.365,0.177 10 false THW 5.073,1.156 5.542,1.354 0.469,0.198 10 false B105 0.594,2.385 0.896,2.583 0.302,0.198 10 false k1 2.427,1.021 2.563,1.219 0.135,0.198 10 false 1 2.438,1.667 2.594,1.844 0.156,0.177 10 false 2 5.969,2.688 6.365,2.833 0.396,0.146 10 false ECM 0.594,2.552 2.906,2.771 2.313,0.219 10 false Engine Coolant Temperature Sensor 6.198,0.708 6.51,0.875 0.313,0.167 10 false 5 V 6.125,0.948 6.313,1.125 0.188,0.177 10 false R 2,1.021 2.365,1.208 0.365,0.188 10 false THW 2.115,1.667 2.396,1.865 0.281,0.198 10 false E2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:
·

If DTCs that are related to different systems are output simultaneously while terminal E2 is used as a ground terminal, terminal E2 may have an open circuit.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (COOLANT TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

OK:

Same value as the actual engine coolant temperature.


Result:
Result Proceed to
-40°C (-40°F) A
140°C (284°F) B
OK (same as actual engine coolant temperature) C


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F).





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
A227218C01
0.542,3.667 0.948,3.948 0.406,0.281 1.583,3.875 1.135,4.188 true 1.792,3.885 2.344,4.208 true 0.719,0.604 0.938,0.813 0.219,0.208 10 false *1 2.615,0.292 2.844,0.49 0.229,0.198 10 false *2 2.406,1.156 2.802,1.344 0.396,0.188 10 false THW 0.76,4.135 1.156,4.365 0.396,0.229 10 false THW 2.438,1.542 2.719,1.729 0.281,0.188 10 false E2 2.417,4.135 2.698,4.333 0.281,0.198 10 false E2 1.542,2.896 1.76,3.104 0.219,0.208 10 false *3 0.667,3.729 0.948,3.906 0.281,0.177 10 false k1
*1 Intake Air Temperature Sensor
*2 ECM
*3 Front view of wire harness connector
(to Engine Coolant Temperature Sensor)


Disconnect the engine coolant temperature sensor connector.


b.

Connect terminals 1 and 2 of the engine coolant temperature sensor wire harness side connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.


g.

Read the value.

Standard:

140°C (284°F)



h.

Reconnect the engine coolant temperature sensor connector.


Result:
Proceed to
OK
NG



OK

NG

3.READ VALUE USING GTS (CHECK FOR OPEN IN ECM)
3.READ VALUE USING GTS (CHECK FOR OPEN IN ECM)
a.
A178586C14
1.854,2.958 2.344,3.25 0.49,0.292 1.302,2.969 1.792,3.26 0.49,0.292 2.177,3.656 2.625,4.313 true 1.615,3.573 1.333,4.313 true 0.76,1.792 0.948,1.938 0.188,0.146 10 false *1 2.531,1.781 2.708,1.938 0.177,0.156 10 false *2 0.479,2.958 0.656,3.125 0.177,0.167 10 false *a 1.094,4.375 1.646,4.542 0.552,0.167 10 false 9(THW) 2.479,4.396 3.01,4.542 0.531,0.146 10 false 14(E2) 1.948,3.031 2.406,3.219 0.458,0.188 10 false B104 1.396,3.042 1.844,3.229 0.448,0.188 10 false B105 2.26,0.781 2.719,0.979 0.458,0.198 10 false THW 2.313,1.115 2.625,1.313 0.313,0.198 10 false E2
*1 Engine Coolant Temperature Sensor
*2 ECM
*a Component with harness connected
(ECM)


Disconnect the engine coolant temperature sensor connector.


b.

Connect terminals THW and E2 of the ECM connector.

HINT:

Before checking, perform a visual and contact pressure check for the ECM connector.



c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.


g.

Read the value.

Standard:

140°C (284°F)



h.

Reconnect the engine coolant temperature sensor connector.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)

NG

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the engine coolant temperature sensor connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.


f.

Read the value.

Standard:

-40°C (-40°F)



g.

Reconnect the engine coolant temperature sensor connector.


Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the engine coolant temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.


Result:
Proceed to
OK
NG


Standard Resistance:
Tester Connection Condition Specified Condition
B105-9 (THW) or k1-1 (THW) - Body ground and other terminals Always 10 kΩ or higher



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)

NG