Home › Engine / Hybrid System › N04C-VJ (ENGINE CONTROL) › ECD SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _096807 N04C-VJ ENGINE CONTROL _0454116 ECD SYSTEM C

N04C-VJ ENGINE CONTROL  ECD SYSTEM  P0335  Crankshaft Position Sensor "A" Circuit  P0339  Crankshaft Position Sensor "A" Circuit Intermittent  


DESCRIPTION

The crankshaft position sensor system consists of a crankshaft position sensor plate and a pickup coil.

The crankshaft position sensor plate has 34 protrusions with 2 teeth missing for detecting top dead center, and is installed to the crankshaft.

The pickup coil outputs 34 signals per engine revolution.

The ECM detects the cylinder identification based on the G signal or the position and angle of the camshaft, and also detects the crankshaft position and engine speed based on the NE signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0335 Crankshaft Position Sensor "A" Circuit Either of the following conditions is met (1 trip detection logic):

(a) No crankshaft position sensor signal to ECM while cranking for 4.7 seconds or more

(b) No crankshaft position sensor signal to ECM while engine running after 3 seconds or more elapsed after STA signal is switched from on to off (Engine speed at 600 rpm or more)


·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft angle sensor plate

·

ECM


Comes on DTC stored
P0339 Crankshaft Position Sensor "A" Circuit Intermittent In conditions (a), (b) and (c), no crankshaft position sensor (NE) signal is input for 0.05 seconds or more.
(1 trip detection logic)

(a) Engine revolution is 1000 rpm or more

(b) NE signal is OFF

(c) 3 seconds or more has lapsed after STA signal is switched from ON to OFF


·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft angle sensor plate

·

ECM


Does not come on DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0335
·

Engine idle or cranking condition

·

Idle the engine for 3 seconds or more


P0339 Engine speed 1000 rpm or more for 5 seconds or more

WIRING DIAGRAM

A347540E01
1.646,0.604 1.948,0.792 0.302,0.188 10 false NE+ 1.656,1.24 1.958,1.427 0.302,0.188 10 false NE- 2.021,0.573 2.229,0.75 0.208,0.177 10 false 1 2.01,1.208 2.188,1.427 0.177,0.219 10 false 2 0.802,1.625 1.031,1.802 0.229,0.177 10 false B5 0.802,1.802 2.531,2.01 1.729,0.208 10 false Crankshaft Position Sensor 3.719,1.594 3.948,1.865 0.229,0.271 10 false * 0.677,3.198 0.875,3.406 0.198,0.208 10 false 3 0.177,4.469 1.188,4.688 1.01,0.219 10 false *: Shielded 0.76,3.927 0.958,4.135 0.198,0.208 10 false k2 0.76,4.104 2.479,4.333 1.719,0.229 10 false Camshaft Position Sensor 0.885,3.208 1.167,3.427 0.281,0.219 10 false VG 1.719,2.896 2.063,3.125 0.344,0.229 10 false G1 1.719,3.521 1.917,3.729 0.198,0.208 10 false G- 2,2.875 2.198,3.083 0.198,0.208 10 false 1 2,3.51 2.198,3.719 0.198,0.208 10 false 2 6.198,4.052 6.865,4.406 0.667,0.354 10 false ECM 6.167,3.823 6.552,3.99 0.385,0.167 10 false B103 5.625,3.427 5.854,3.625 0.229,0.198 10 false 14 6.01,3.604 6.219,3.813 0.208,0.208 10 false G- 6,2.979 6.281,3.177 0.281,0.198 10 false G+ 5.635,2.792 5.854,2.979 0.219,0.188 10 false 13 5.635,2.177 5.875,2.375 0.24,0.198 10 false 15 6,2.375 6.375,2.563 0.375,0.188 10 false VCG 6,1.781 6.24,2.031 0.24,0.25 10 false E1 5.667,1.573 5.865,1.76 0.198,0.188 10 false 1 5.677,1.135 5.917,1.323 0.24,0.188 10 false 8 6,1.333 6.354,1.552 0.354,0.219 10 false NE- 5.99,0.688 6.344,0.875 0.354,0.188 10 false NE+ 5.656,0.479 5.854,0.646 0.198,0.167 10 false 7 5.563,2.969 6.052,3.146 0.49,0.177 10 false B103 5.563,3.604 6.052,3.781 0.49,0.177 10 false B103 5.563,2.344 6.052,2.521 0.49,0.177 10 false B103 5.563,1.313 6.052,1.49 0.49,0.177 10 false B103 5.563,0.667 6.052,0.844 0.49,0.177 10 false B103 5.563,1.76 6.052,1.938 0.49,0.177 10 false B102

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK CRANKSHAFT POSITION SENSOR
a.
A256050C05
2.354,0.354 2.792,0.594 0.438,0.24 2.573,0.927 2.292,1.708 true 2.635,0.938 2.865,1.719 true 2.427,0.406 2.844,0.573 0.417,0.167 10 false B103 2.729,1.771 3.198,1.979 0.469,0.208 10 false 7(NE+) 2.094,1.792 2.573,1.99 0.479,0.198 10 false 8(NE-) 3.125,3.688 3.427,3.875 0.302,0.188 10 false GND 0.094,3.667 0.5,3.875 0.406,0.208 10 false NE+ 0.125,0.083 0.458,0.302 0.333,0.219 10 false *a 2.594,2.521 3.344,2.74 0.75,0.219 10 false 5 V/DIV. 1.292,4.385 3.281,4.583 1.99,0.198 10 false 20 msec./DIV.
*a Component with harness connected
(ECM)


While idling the engine, check the waveform of the ECM connectors using an oscilloscope.

Standard:
Tester Connection Condition Specified Condition
B103-7 (NE+) - B103-8 (NE-) Engine idling Correct waveform appears as shown


HINT:
·

The higher the engine speed becomes, the larger the amplitude.

·

The higher the engine speed becomes, the shorter the cycle.

·

A DTC may be detected due to noise.




Result:
Proceed to
OK
NG



OK

NG

2.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)
2.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)
a.

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B5-1 (NE+) - B103-7 (NE+) Always Below 1 Ω
B5-2 (NE-) - B103-8 (NE-) Always Below 1 Ω
B5-1 (NE+) or B103-7 (NE+) - Body ground Always 10 kΩ or higher
B5-2 (NE-) or B103-8 (NE-) - Body ground Always 10 kΩ or higher



d.

Reconnect the crankshaft position sensor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

4.CHECK CRANKSHAFT POSITION SENSOR (SENSOR INSTALLATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK CRANKSHAFT POSITION SENSOR (SENSOR INSTALLATION)
a.

Check the crankshaft position sensor installation condition.


A369509E04
0.51,1.698 0.813,1.896 0.302,0.198 10 false OK 2.656,1.781 2.948,1.979 0.292,0.198 10 false NG 1.667,1.552 2.344,1.75 0.677,0.198 10 false Clearance

OK:

The crankshaft position sensor is installed properly.


Result:
Proceed to
OK
NG



OK

5.INSPECT CRANKSHAFT POSITION SENSOR PLATE

NG

SECURELY REINSTALL CRANKSHAFT POSITION SENSOR

5.INSPECT CRANKSHAFT POSITION SENSOR PLATE
a.

Check the teeth of the crankshaft angle sensor plate.

OK:

The sensor plate teeth do not have any cracks or deformation.



Result:
Proceed to
OK
NG



OK

NG

REPLACE CRANKSHAFT POSITION SENSOR PLATE