Home › Engine / Hybrid System › N04C-VJ (ENGINE CONTROL) › ECD SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _096807 N04C-VJ ENGINE CONTROL _0454116 ECD SYSTEM C

N04C-VJ ENGINE CONTROL  ECD SYSTEM  P0500  Vehicle Speed Sensor "A"  


DESCRIPTION

The combination meter assembly converts vehicle speed pulse signals from the ABS speed sensor installed on the transmission into vehicle speed pulse signals (equivalent to 8 pulses for each rotation of the transmission shaft), outputs them as vehicle speed signals, and inputs them into the ECM.

A160075E02
1.281,1.396 2.885,1.635 1.604,0.24 10 false Speedometer Sensor 2.979,1.396 5.073,1.594 2.094,0.198 10 false Combination Meter Assembly 5.719,1.375 6.927,1.698 1.208,0.323 10 false ECM 4.719,0.135 5.24,0.313 0.521,0.177 10 false Pulse 2.729,0.135 3.25,0.313 0.521,0.177 10 false Pulse

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0500 Vehicle Speed Sensor "A" All conditions below are detected continuously for 8 seconds or more:
(2 trip detection logic)

(a) Vehicle speed signal: 0 km/h (0 mph)

(b) Engine speed: 1500 to 2500 rpm

(c) Engine coolant temperature: 70°C (158°F) or more

(d) ECT sensor, accelerator pedal position sensor, and MAF meter are all normal


·

Open or short in vehicle speed sensor circuit

·

Vehicle speed sensor

·

Combination meter

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0500 Drive the vehicle at 10 km/h (6.25 mph) or more

WIRING DIAGRAM

A261586E01
2.115,1.021 2.385,1.219 0.271,0.198 10 false +S 5.542,0.979 5.969,1.167 0.427,0.188 10 false SPD 0.948,1.74 1.219,1.958 0.271,0.219 10 false J1 0.958,1.917 2.802,2.177 1.844,0.26 10 false Combination Meter 2.427,0.865 2.698,1.052 0.271,0.188 10 false 6 5.24,0.813 5.563,1.042 0.323,0.229 10 false 7 5.813,2.219 6.406,2.563 0.594,0.344 10 false ECM 5.167,1 5.552,1.208 0.385,0.208 10 false A57 5.115,1.594 5.594,1.792 0.479,0.198 10 false B102 5.198,1.417 5.531,1.635 0.333,0.219 10 false 11 5.552,1.594 5.906,1.771 0.354,0.177 10 false E01

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OPERATION OF SPEEDOMETER
a.

Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.

HINT:
·

The vehicle speed sensor is operating normally if the speedometer reading is normal.

·

If the speedometer does not operate, check it by following the procedure described in speedometer malfunction.




b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Vehicle Speed.


d.

Drive the vehicle.


e.

Read the value displayed on the GTS.

OK:

Speedometer operates normally.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (VEHICLE SPEED)

NG

CHECK SPEEDOMETER CIRCUIT (INCLUDE SPEED SENSOR)

2.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.


e.

Check the vehicle speed at an engine speed of 2000 rpm or more while the vehicle is running.

OK:

Same value as actual vehicle speed.



Result:
Proceed to
OK
NG



OK

NG

3.INSPECT ECM (SPD VOLTAGE)
3.INSPECT ECM (SPD VOLTAGE)
a.
A424147C02
0.188,0.365 0.51,0.573 0.323,0.208 2.844,0.365 3.219,0.573 0.375,0.208 0.708,1.729 0.51,0.99 true 3.042,1.76 3.24,1.167 true 3.125,3.677 3.427,3.844 0.302,0.167 10 false GND 0.063,0.094 0.365,0.26 0.302,0.167 10 false *a 0.24,0.406 0.542,0.573 0.302,0.167 10 false A57 2.885,0.396 3.229,0.594 0.344,0.198 10 false B102 2.802,1.802 3.323,2.031 0.521,0.229 10 false 11(E01) 0.51,1.802 1.01,2.021 0.5,0.219 10 false 7(SPD)
*a Component with harness connected
(ECM)


Move the transmission gear selector lever to the neutral position.


b.

Jack up the vehicle.


c.

Turn the ignition switch to ON.


d.

Measure the voltage of the ECM connectors as the wheel is turned slowly.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A57-7 (SPD) - B102-11 (E01) Ignition switch ON Voltage generated intermittently


HINT:

The output voltage should fluctuate up and down similarly to the diagram when the wheel is turned slowly.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION METER - ECM)