Home › Engine / Hybrid System › N04C-VJ (ENGINE CONTROL) › ECD SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _096807 N04C-VJ ENGINE CONTROL _0454116 ECD SYSTEM C

N04C-VJ ENGINE CONTROL  ECD SYSTEM  P0560  System Voltage  


DESCRIPTION

While the ignition switch is off, battery voltage is supplied to terminal BATT of the ECM for storing DTCs and fuel injection feedback learning values.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0560 System Voltage Condition (a) or (b) continues:
(1 trip detection logic)

(a) Significant decrease in battery voltage

(b) Open in back-up power source circuit


·

Open in back-up power source circuit

·

Low battery voltage

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0560 Ignition switch ON for 3 seconds or more

WIRING DIAGRAM

A398545E07
0.688,0.99 1.333,1.177 0.646,0.188 10 false FL MAIN 1.229,0.656 2.042,0.844 0.813,0.188 10 false R/B NO. 2-B 2.802,0.667 3.073,0.844 0.271,0.177 10 false P/I 3.885,0.656 4.563,0.854 0.677,0.198 10 false EFI-MAIN 1.323,1.948 2,2.146 0.677,0.198 10 false Battery 5.344,1.354 5.875,1.531 0.531,0.177 10 false B102 5.385,0.479 5.729,0.656 0.344,0.177 10 false A57 5.792,0.365 6.198,0.531 0.406,0.167 10 false BATT 5.813,1.354 6.313,1.531 0.5,0.177 10 false E01 6.167,2.052 6.563,2.24 0.396,0.188 10 false ECM 5.427,0.271 5.708,0.448 0.281,0.177 10 false 23 5.427,1.167 5.75,1.344 0.323,0.177 10 false 11

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of this circuits related to this system before performing the following procedure.

·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - BATTERY)
a.

Disconnect the negative battery terminal.


b.

Disconnect the positive battery terminal.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A57-23 (BATT) - Positive battery terminal Always Below 1 Ω
A57-23 (BATT) or Positive battery terminal - Body ground Always 10 kΩ or higher



e.

Reconnect the ECM connector.


f.

Reconnect the positive battery terminal.


g.

Reconnect the negative battery terminal.


Result:
Proceed to
OK
NG



OK

2.INSPECT ECM (BATT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT ECM (BATT VOLTAGE)
a.

Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A57-23 (BATT) - B102-11 (E01) Always 11 to 14 V



c.

Reconnect the ECM connector.


Result:
Result Proceed to
NG A
OK B



A

3.INSPECT BATTERY

B

3.INSPECT BATTERY
a.

Check that the battery is not depleted.

OK:

Battery is not depleted.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE BATTERY