Home › Engine / Hybrid System › N04C-VJ (ENGINE CONTROL) › ECD SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _096807 N04C-VJ ENGINE CONTROL _0454116 ECD SYSTEM C

N04C-VJ ENGINE CONTROL  ECD SYSTEM  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.

If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and sets the DTC.

This monitor runs when the vehicle has been driven at 20 km/h (12.4 mph) for more than 20 seconds.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High When conditions (a), (b) and (c) are met, positive (+B) battery voltage of 10.5 V or more is applied to ECM for 20 seconds:
(1 trip detection logic)
(a) Vehicle speed is more than 20 km/h (12.4 mph)
(b) Engine speed is more than 1000 rpm
(c) STA signal is ON
·

Starter relay circuit

·

Ignition switch

·

Park/neutral position switch

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0617 Drive the vehicle at a vehicle speed of 20 km/h or higher and an engine speed of 1000 rpm or higher for 25 seconds or more.

WIRING DIAGRAM

A483973E01
0.958,0.948 1.417,1.146 0.458,0.198 10 false AM2 2.969,0.927 3.594,1.115 0.625,0.188 10 false ST NO. 2 1.313,3.208 1.938,3.396 0.625,0.188 10 false ST NO. 1 0.448,3.594 1.073,3.781 0.625,0.188 10 false FL MAIN 2.24,4.906 2.719,5.115 0.479,0.208 10 false Starter 1.063,4.875 1.573,5.073 0.51,0.198 10 false Battery 6.125,0.771 6.615,1 0.49,0.229 10 false STA 4.177,3.729 4.427,3.906 0.25,0.177 10 false ST 5.656,2.833 6.135,3.031 0.479,0.198 10 false B103 6.281,4.729 6.677,4.927 0.396,0.198 10 false ECM 2.563,4.208 2.813,4.385 0.25,0.177 10 false ST 2.229,4.219 2.375,4.406 0.146,0.188 10 false B 1.906,4.219 2.208,4.417 0.302,0.198 10 false C11 2.813,4.219 3.115,4.417 0.302,0.198 10 false B99 1.969,4 2.115,4.188 0.146,0.188 10 false 1 2.885,4.01 3.031,4.198 0.146,0.188 10 false 1 3.979,3.25 4.125,3.438 0.146,0.188 10 false 1 3.969,4.208 4.115,4.396 0.146,0.188 10 false 2 3.51,3.271 3.656,3.458 0.146,0.188 10 false 5 3.51,4.208 3.656,4.396 0.146,0.188 10 false 3 5.76,0.583 5.969,0.781 0.208,0.198 10 false 6 2.719,0.677 2.865,0.865 0.146,0.188 10 false 9 1.365,0.667 1.573,0.865 0.208,0.198 10 false 12 1.604,0.677 2.021,0.875 0.417,0.198 10 false AM2 2.365,0.677 2.698,0.865 0.333,0.188 10 false ST2 1.469,1.177 1.781,1.365 0.313,0.188 10 false J63 1.49,1.333 3.135,1.542 1.646,0.208 10 false Ignition Switch Assembly 6.115,2.833 6.698,3.031 0.583,0.198 10 false NSW 4.24,1.813 5.604,2.417 1.365,0.604 10 false Park/Neutral Position Switch 5.688,0.781 6.167,0.979 0.479,0.198 10 false A57 4.24,1.625 4.844,1.823 0.604,0.198 10 false B135 5.74,2.625 5.948,2.823 0.208,0.198 10 false 20

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of this circuits related to this system before performing the following procedure.

·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:
·

The following troubleshooting flowchart is based on the premise that the engine is cranked normally. If the engine does not crank, proceed to the problem symptoms table (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>PROBLEM SYMPTOMS TABLE).

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


e.

Check the value displayed on the tester when the ignition switch is turned to ON and START.

OK:
Ignition Switch Condition Starter Signal
ON OFF
START ON



Result:
Result Proceed to
OK A
NG B



A

B

2.INSPECT IGNITION SWITCH ASSEMBLY
2.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly (Click hereEngine / Hybrid System>N04C-VJ (STARTING)>IGNITION SWITCH>INSPECTION).


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - IGNITION SWITCH ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (ECM - IGNITION SWITCH ASSEMBLY)
a.

Disconnect the ECM connector.


b.

Disconnect the ignition switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J63-9 (ST2) - A57-6 (STA) Always Below 1 Ω
J63-9 (ST2) or A57-6 (STA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ECM - STARTER RELAY, PARK/NEUTRAL POSITION SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ECM - STARTER RELAY, PARK/NEUTRAL POSITION SWITCH)
a.

Disconnect the park/neutral position switch connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 1 or A57-6 (STA) - Body ground Always 10 kΩ or higher
J63-9 (ST2) or A57-6 (STA) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the park/neutral position switch connector.


f.

Reinstall the starter relay.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR