Home › Engine / Hybrid System › N04C-VJ (ENGINE CONTROL) › ECD SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _096807 N04C-VJ ENGINE CONTROL _0454116 ECD SYSTEM J

N04C-VJ ENGINE CONTROL  ECD SYSTEM  DPF Switch and Buzzer Circuit  


DESCRIPTION

The DPF (Diesel Particulate Filter) system is controlled by the ECM to activate the forcible regeneration function automatically. However, depending on driving conditions, the forcible regeneration function may not be activated. In such a case, the indicator light on the combination meter and the DPF switch light blink to inform the driver. When the DPF switch is pressed, RGSW signals will be input into the ECM and the forcible regeneration function will activate.

If the vehicle continues to be driven without performing forcible regeneration while the indicator light is on, a buzzer intermittently sounds to inform the driver.

WIRING DIAGRAM

A401621E03
6.229,1.031 6.74,1.208 0.51,0.177 10 false RGSW 6.313,2.073 6.635,2.26 0.323,0.188 10 false A57 6.302,2.229 6.688,2.406 0.385,0.177 10 false ECM 3.458,1.458 3.781,1.646 0.323,0.188 10 false J30 3.448,1.625 4.917,1.833 1.469,0.208 10 false DPF Switch Assembly 0.167,1.031 2.146,1.417 1.979,0.385 10 false From Instrument Panel Junction Block Terminal (4D-19) 3.625,0.917 3.771,1.094 0.146,0.177 10 false B 4.208,0.917 4.354,1.094 0.146,0.177 10 false E 3.427,0.917 3.542,1.104 0.115,0.188 10 false 4 4.417,0.906 4.531,1.094 0.115,0.188 10 false 1 5.906,0.906 6.125,1.094 0.219,0.188 10 false 14

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of this circuits related to this system before performing the following procedure.

·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



PROCEDURE

1.CHECK DPF SWITCH ASSEMBLY (POWER SOURCE)
a.
A401959C02
0.5,0.927 0.875,1.198 0.375,0.271 2.01,1.302 2.323,1.667 true 0.146,0.115 0.458,0.313 0.313,0.198 10 false *a 0.583,0.979 0.896,1.177 0.313,0.198 10 false J30 2.229,1.677 2.635,1.885 0.406,0.208 10 false 4 (B)
*a Front view of wire harness connector
(to DPF Switch Assembly)


Disconnect the DPF switch assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J30-4 (B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.INSPECT DPF SWITCH ASSEMBLY (RESISTANCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH ASSEMBLY - BATTERY)

2.INSPECT DPF SWITCH ASSEMBLY (RESISTANCE)

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (DPF SWITCH ASSEMBLY - ECM)

NG

REPLACE DPF SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (DPF SWITCH ASSEMBLY - ECM)
a.

Check the wire harness and connector.

i.

Disconnect the DPF switch assembly connector.


ii.

Disconnect the ECM connectors.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J30-1 (E) - A57-14 (RGSW) Always Below 1 Ω
J30-1 (E) or A57-14 (RGSW) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR