Home › Engine / Hybrid System › N04C-VJ (ENGINE CONTROL) › ECD SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _096807 N04C-VJ ENGINE CONTROL _0454116 ECD SYSTEM C

N04C-VJ ENGINE CONTROL  ECD SYSTEM  P0102  Mass Air Flow Circuit Low  P0103  Mass Air Flow Circuit High  


DESCRIPTION

The intake mass air flow meter assembly consists of a platinum hot wire, temperature sensor and control circuit installed in a plastic housing. The temperature sensor (located in the intake air by-pass of the housing) detects the intake air temperature.

There is little variation in the output from the intake mass air flow meter assembly, as it is hardly affected by the resistance of the wire harness.

The internal circuit of the intake mass air flow meter assembly contains a hot wire and cold wire. A voltage is output through a bridge circuit (refer to the illumination) indicating the cooling of the hot wire according to the intake air amount. This voltage is then converted into a periodic signal by the periodic signal conversion circuit and output to the ECM. The frequency varies between approximately 250 and 11000 Hz depending on the air flow rate. The ECM calculates the mass air flow rate based on this frequency.

A221589E01
1.667,0.506 1.900,0.704 0.232,0.198 10 +B 1.632,0.836 2.754,1.019 1.121,0.184 10 Power Transistor 2.767,1.536 3.743,1.709 0.975,0.173 10 Output Voltage 2.113,2.307 3.404,2.650 1.290,0.343 10 Periodic Signal Conversion Circuit 2.2,3.301 3.418,3.478 1.218,0.177 10 Output Frequency 0.047,2.714 1.332,3.060 1.286,0.345 10 Temperature Sensor (Thermistor) 2.106,1.158 3.818,1.362 1.711,0.205 10 Platinum Hot Wire (Heater) 3.559,2.926 5.275,3.121 1.716,0.195 10 Platinum Hot Wire (Heater) 4.983,3.269 7.121,3.452 2.137,0.184 10 Temperature Sensor (Thermistor) 2.048,1.221 1.871,1.221 1.871,1.221 1.683,1.686 false 0.526,2.687 0.526,2.071 0.526,2.071 1.298,1.783 false 2.721,1.604 2.609,1.604 2.609,1.604 2.412,1.921 false 4.084,2.874 4.084,2.454 4.084,2.454 4.54,1.865 false 6.036,3.238 6.036,2.902 6.036,2.902 4.817,2.099 false

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0102 Mass Air Flow Circuit Low Mass air flow meter signal frequency is less than 850 Hz with the engine speed at less than 5000 rpm or less for 3 seconds (1 trip detection logic).
·

Open or short in mass air flow meter sub-assembly circuit

·

Mass air flow meter sub-assembly

·

ECM


Comes on DTC stored
P0103 Mass Air Flow Circuit High Mass air flow meter signal frequency is more than 9800 Hz with the engine speed at less than 5000 rpm or less for 3 seconds (1 trip detection logic).
·

Open or short in mass air flow meter sub-assembly circuit

·

Mass air flow meter sub-assembly

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0102
P0103
3 seconds or more after engine is started

WIRING DIAGRAM

A372415E03
2.927,0.646 3.99,0.833 1.063,0.188 10 false EFI NO. 2 4.104,0.385 4.333,0.583 0.229,0.198 10 false 3 4.333,0.49 4.594,0.708 0.26,0.219 10 false +B 4.917,0.49 5.167,0.667 0.25,0.177 10 false VG 4.865,0.979 5.188,1.198 0.323,0.219 10 false E2G 5.26,0.385 5.479,0.615 0.219,0.229 10 false 5 5.26,0.875 5.469,1.094 0.208,0.219 10 false 4 6.135,0.313 6.385,0.51 0.25,0.198 10 false 17 6.083,0.49 6.438,0.656 0.354,0.167 10 false B105 6.146,0.792 6.396,0.979 0.25,0.188 10 false 18 6.083,0.99 6.5,1.188 0.417,0.198 10 false B105 6.51,0.49 6.802,0.677 0.292,0.188 10 false VG 6.5,0.958 6.865,1.146 0.365,0.188 10 false EVG 6.51,2.594 6.781,2.781 0.271,0.188 10 false +B 6.51,3.01 7.083,3.229 0.573,0.219 10 false MREL 6.573,3.375 7,3.677 0.427,0.302 10 false ECM 6.146,2.396 6.427,2.594 0.281,0.198 10 false 24 6.125,2.604 6.458,2.802 0.333,0.198 10 false A57 6.156,2.833 6.448,3.01 0.292,0.177 10 false 25 6.115,3.031 6.448,3.219 0.333,0.188 10 false A56 5.229,2.76 5.802,2.979 0.573,0.219 10 false EFI NO.2 4.833,2.385 5.063,2.573 0.229,0.188 10 false 4 4.813,2.604 5.063,2.781 0.25,0.177 10 false 2D 4.865,2.833 5.156,3.031 0.292,0.198 10 false 2 4.813,3.031 5.115,3.24 0.302,0.208 10 false 2D 4.021,3.25 4.281,3.438 0.26,0.188 10 false EFI 2.969,3.677 4.792,3.865 1.823,0.188 10 false No. 2 Integration Relay 2.885,2.75 3.563,2.969 0.677,0.219 10 false EFI-MAIN 2.521,2.385 2.719,2.594 0.198,0.208 10 false 1 2.5,2.604 2.74,2.781 0.24,0.177 10 false 2E 2.531,2.833 2.708,3.01 0.177,0.177 10 false 3 2.49,3.021 2.75,3.229 0.26,0.208 10 false 2D 1.635,2.76 1.917,3 0.281,0.24 10 false P/I 0.615,2.76 1.469,2.979 0.854,0.219 10 false R/B NO.2-B 0.417,3.385 1.115,3.615 0.698,0.229 10 false FL MAIN 0.552,4.042 1.125,4.26 0.573,0.219 10 false Battery 3.729,1.448 5.948,1.625 2.219,0.177 10 false Mass Air Flow Meter Sub-assembly 3.771,1.281 4.094,1.5 0.323,0.219 10 false B51

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.CHECK MASS AIR FLOW METER SUB-ASSEMBLY (POWER SOURCE)
A148358C09
0.104,1.865 0.656,2.198 0.552,0.333 1.677,2.083 1.052,2.51 true 0.104,0.104 0.302,0.281 0.198,0.177 10 false *a 0.813,2.51 1.063,2.698 0.25,0.188 10 false +B 0.26,1.948 0.542,2.104 0.281,0.156 10 false B51
*a Front view of wire harness connector
(to Mass Air Flow Meter Sub-assembly)


a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B51-3 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - NO. 2 INTEGRATION RELAY)
2.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B51-5 (VG) - B105-17 (VG) Always Below 1 Ω
B51-4 (E2G) - B105-18 (EVG) Always Below 1 Ω
B51-5 (VG) or B105-17 (VG) - Body ground Always 10 kΩ or higher
B51-4 (E2G) or B105-18 (EVG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

3.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
a.

Replace mass air flow meter sub-assembly (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL).


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Start the engine and wait for 3 seconds or more.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the DTC.


Result:
Result Proceed to
DTC P0102 or P0103 is output A
DTC is not output B



A

B

END

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - NO. 2 INTEGRATION RELAY)
a.

Remove the No. 2 Integration relay from the No. 2 relay block and junction block assembly.


b.

Disconnect the mass air flow meter sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B51-3 (+B) - 2D-4 Always Below 1 Ω
B51-3 (+B) or 2D-4 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - NO. 2 INTEGRATION RELAY)