Home › Engine / Hybrid System › N04C-VJ (ENGINE CONTROL) › ECD SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _096807 N04C-VJ ENGINE CONTROL _0454116 ECD SYSTEM C

N04C-VJ ENGINE CONTROL  ECD SYSTEM  P0112  Intake Air Temperature Circuit Low Input  P0113  Intake Air Temperature Circuit High Input  


DESCRIPTION

The intake air temperature sensor is built into the mass air flow meter sub-assembly and senses the intake air temperature. A thermistor built in the sensor changes the resistance value according to the intake air temperature. The lower the intake air temperature is, the greater the thermistor resistance value is, and the higher the intake air temperature is, the lower the thermistor resistance value is (see Fig. 1).

The intake air temperature sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the intake air temperature sensor from terminal THA via a resistor R. The resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes in accordance with changes in the intake air temperature, the voltage at terminal THA also changes. Based on this signal, the ECM increases the fuel injection volume to improve driveability during cold engine operation.

A283580E19
3.354,2.271 3.74,1.99 false 2.26,0.406 2.833,0.667 0.573,0.26 10 Fig. 1: 3.292,4.271 4.167,4.5 0.875,0.229 10 Temperature 2.396,0.969 2.771,1.219 0.375,0.25 10 (kΩ) 2.281,1.146 2.521,1.365 0.24,0.219 10 30 2.281,1.583 2.521,1.802 0.24,0.219 10 10 2.354,1.875 2.594,2.094 0.24,0.219 10 5 2.354,2.094 2.594,2.313 0.24,0.219 10 3 2.354,2.26 2.51,2.479 0.156,0.219 10 2 2.344,2.531 2.594,2.75 0.25,0.219 10 1 2.24,2.833 2.479,3.052 0.24,0.219 10 0.5 2.24,3.198 2.479,3.417 0.24,0.219 10 0.2 2.24,3.469 2.479,3.688 0.24,0.219 10 0.1 2.281,1.323 2.531,1.542 0.25,0.219 10 20 2.542,3.823 2.781,4.042 0.24,0.219 10 -20 2.938,3.823 3.177,4.042 0.24,0.219 10 0 3.208,3.823 3.448,4.042 0.24,0.219 10 20 3.521,3.823 3.76,4.042 0.24,0.219 10 40 3.833,3.823 4.073,4.042 0.24,0.219 10 60 4.146,3.823 4.385,4.042 0.24,0.219 10 80 4.385,3.823 4.625,4.042 0.24,0.219 10 100 2.583,4 2.823,4.219 0.24,0.219 10 -4 2.896,4 3.135,4.219 0.24,0.219 10 32 3.208,4 3.448,4.219 0.24,0.219 10 68 3.479,4 3.729,4.25 0.25,0.25 10 104 3.792,4 4.125,4.25 0.333,0.25 10 140 4.094,4 4.417,4.25 0.323,0.25 10 176 4.385,4 4.708,4.25 0.323,0.25 10 212 4.677,3.823 5,4.073 0.323,0.25 10 (°C) 4.677,4 5,4.25 0.323,0.25 10 (°F) 3.802,1.896 4.583,2.167 0.781,0.271 10 Acceptable 2.26,0.719 3.083,0.917 0.823,0.198 10 Resistance 2.24,3.021 2.479,3.24 0.24,0.219 10 0.3

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0112 Intake Air Temperature Circuit Low Input Short in intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic)
·

Short in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter sub-assembly)

·

ECM


Comes on DTC stored
P0113 Intake Air Temperature Circuit High Input Open in intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic)
·

Open in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter sub-assembly)

·

ECM


Comes on DTC stored

HINT:

When DTC P0112 or P0113 is detected, check the intake air temperature by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Intake Air.

Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) Short circuit


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0112
P0113
Ignition switch ON for 0.5 second or more

WIRING DIAGRAM

A398533E10
0.281,2.75 2.198,2.99 1.917,0.24 10 false Intake Air Temperature Sensor 0.271,2.552 0.729,2.75 0.458,0.198 10 false B51 4.969,1.323 5.427,1.521 0.458,0.198 10 false B105 4.969,1.896 5.427,2.094 0.458,0.198 10 false B104 1.542,1.219 2,1.417 0.458,0.198 10 false THA 1.646,1.76 2.104,1.958 0.458,0.198 10 false E2 5.458,1.208 5.917,1.406 0.458,0.198 10 false THA 5.479,1.781 5.938,1.979 0.458,0.198 10 false E2 5.083,1.698 5.448,1.896 0.365,0.198 10 false 14 5.094,1.104 5.385,1.302 0.292,0.198 10 false 10 2.052,1.76 2.26,1.958 0.208,0.198 10 false 2 2.031,1.198 2.24,1.396 0.208,0.198 10 false 1 6.198,0.844 6.656,1.042 0.458,0.198 10 false 5 V 6.094,1.115 6.552,1.313 0.458,0.198 10 false R 5.875,2.823 6.333,3.021 0.458,0.198 10 false ECM 0.271,2.979 3.229,3.219 2.958,0.24 10 false (Intake Mass Air Flow Meter Sub-assembly)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:
·

If DTCs that are related to different systems are output simultaneously while terminal E2 is used as a ground terminal, terminal E2 may have an open circuit.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.



PROCEDURE

1.READ VALUE USING GTS (INTAKE AIR TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.


e.

Read the value.

Standard:

Same value as the actual intake air temperature.


Result:
Temperature Display Proceed to
-40°C (-40°F) A
140°C (284°F) B
OK (same as actual intake air temperature) C


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F).





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
A265931C01
1.51,2.844 1.875,3.094 0.365,0.25 1.167,4.313 1.417,3.802 true 1.594,3.792 1.885,4.323 true 0.552,2.729 0.792,2.906 0.24,0.177 10 false *a 0.823,1.76 1.021,1.917 0.198,0.156 10 false *1 2.583,1.781 2.781,1.938 0.198,0.156 10 false *2 1.583,2.896 1.896,3.052 0.313,0.156 10 false B51 1.031,4.365 1.552,4.552 0.521,0.188 10 false THA 1.854,4.365 2.229,4.552 0.375,0.188 10 false E2
*1 Mass Air Flow Meter Sub-assembly
*2 Front view of wire harness connector
(to Mass Air Flow Meter Sub-assembly)
*a Front view of wire harness connector
(to Mass Air Flow Meter Sub-assembly)


a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Connect terminals 1 (THA) and 2 (E2) of the mass air flow meter sub-assembly wire harness side connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.


g.

Read the value.

Standard:

140°C (284°F)



Result:
Proceed to
OK
NG



OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

3.READ VALUE USING GTS (CHECK FOR OPEN IN ECM)
3.READ VALUE USING GTS (CHECK FOR OPEN IN ECM)
A178586C05
1.854,2.958 2.344,3.25 0.49,0.292 1.302,2.969 1.792,3.26 0.49,0.292 2.177,3.656 2.625,4.313 true 1.521,3.583 1.24,4.323 true 0.76,1.792 0.948,1.938 0.188,0.146 10 false *1 2.531,1.781 2.708,1.938 0.177,0.156 10 false *2 0.479,2.958 0.656,3.125 0.177,0.167 10 false *a 1,4.385 1.552,4.552 0.552,0.167 10 false 10(THA) 2.479,4.396 3.01,4.542 0.531,0.146 10 false 14(E2) 1.948,3.031 2.406,3.219 0.458,0.188 10 false B104 1.396,3.042 1.844,3.229 0.448,0.188 10 false B105
*1 Mass Air Flow Meter Sub-assembly
*2 ECM
*a Component with harness connected
(ECM)


a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Connect terminals THA and E2 of the ECM connector.

HINT:

Before checking, perform a visual and contact pressure check on the ECM connector.



c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.


g.

Read the value.

Standard:

140°C (284°F)



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - MASS AIR FLOW METER SUBASSEMBLY)

NG

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.


f.

Read the value.

Standard:

-40°C (-40°F)



Result:
Proceed to
OK
NG



OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER SUB-ASSEMBLY)
5.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER SUB-ASSEMBLY)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the valve(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B105-10 (THA) or B51-1 (THA) - Body ground Always 10 kΩ or higher
B51-2 (E2) or B104-14 (E2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - MASS AIR FLOW METER SUB-ASSEMBLY)