Home › Engine / Hybrid System › N04C-VJ (ENGINE CONTROL) › ECD SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _096807 N04C-VJ ENGINE CONTROL _0454116 ECD SYSTEM C

N04C-VJ ENGINE CONTROL  ECD SYSTEM  P0201  Injector Circuit / Open - (Cylinder 1)  P0202  Injector Circuit / Open - (Cylinder 2)  P0203  Injector Circuit / Open - (Cylinder 3)  P0204  Injector Circuit / Open - (Cylinder 4)  P062D  No. 1 Fuel Injector Driver Circuit Performance  


DESCRIPTION

The injector driver assembly has been adopted to drive the injector assembly at high speeds. The injector driver assembly has realized high-speed driving under high fuel pressure conditions through the use of a DC/DC converter sub-assembly that provides a high-voltage, quick-charging system.

The ECM constantly monitors the injector driver assembly and stops the engine if an abnormal condition is detected.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0201 Injector Circuit / Open - (Cylinder 1) Diagnosis Condition:
·

Battery voltage is 11 V or higher other than during a deceleration fuel cut with the engine running

·

Open or short in No. 1 injector circuit for 0.5 second or more.


(1 tripdetection logic)
·

Open or short in injector driver assembly circuit

·

No. 1 injector assembly

·

Injector driver assembly

·

ECM


Comes on DTC stored
P0202 Injector Circuit / Open - (Cylinder 2) Diagnosis Condition:
·

Battery voltage is 11 V or higher other than during a deceleration fuel cut with the engine running

·

Open or short in No. 2 injector circuit for 0.5 second or more.


(1 tripdetection logic)
·

Open or short in injector driver assembly circuit

·

No. 2 injector assembly

·

Injector driver assembly

·

ECM


Comes on DTC stored
P0203 Injector Circuit / Open - (Cylinder 3) Diagnosis Condition:
·

Battery voltage is 11 V or higher other than during a deceleration fuel cut with the engine running

·

Open or short in No. 3 injector circuit for 0.5 second or more.


(1 tripdetection logic)
·

Open or short in injector driver assembly circuit

·

No. 3 injector assembly

·

Injector driver assembly

·

ECM


Comes on DTC stored
P0204 Injector Circuit / Open - (Cylinder 4) Diagnosis Condition:
·

Battery voltage is 11 V or higher other than during a deceleration fuel cut with the engine running

·

Open or short in No. 4 injector circuit for 0.5 second or more.


(1 tripdetection logic)
·

Open or short in injector driver assembly circuit

·

No. 4 injector assembly

·

Injector driver assembly

·

ECM


Comes on DTC stored
P062D No. 1 Fuel Injector Driver Circuit Performance Diagnosis Condition:
·

Engine speed of 500 rpm or higher, battery voltage of 11 V or more

·

Injection actuation waveform does not match between ECM and injector driver for 0.5 second or more.


(1 tripdetection logic)
·

Open or short in injector driver assembly circuit

·

Injector assembly

·

Injector driver assembly

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0201
P0202
P0203
P0204
P062D
Idling for 5 seconds or more

WIRING DIAGRAM

A394582E04
0.844,1.073 1.188,1.271 0.344,0.198 10 false P/I 0.448,2.063 1.281,2.26 0.833,0.198 10 false R/B NO.2-B 0.448,2.667 1.104,2.875 0.656,0.208 10 false FL-MAIN 0.615,3.865 1.208,4.073 0.594,0.208 10 false Battery 2.177,3.24 4.083,3.448 1.906,0.208 10 false No. 2 Integration Relay 1.823,0.698 2.167,0.896 0.344,0.198 10 false 1 1.802,0.906 2.146,1.104 0.344,0.198 10 false 2E 1.833,1.094 2.177,1.292 0.344,0.198 10 false 3 1.802,1.271 2.052,1.469 0.25,0.198 10 false 2D 2.396,1.052 3.063,1.24 0.667,0.188 10 false EFI-MAIN 2.542,2.094 2.875,2.281 0.333,0.188 10 false EDU 3.333,1.531 3.667,1.719 0.333,0.188 10 false EFI 3.333,2.552 3.667,2.74 0.333,0.188 10 false EDU 4.146,0.719 4.375,0.917 0.229,0.198 10 false 4 4.115,0.917 4.458,1.115 0.344,0.198 10 false 2D 4.146,1.094 4.49,1.292 0.344,0.198 10 false 2 4.146,1.75 4.49,1.948 0.344,0.198 10 false 4 4.104,1.938 4.448,2.135 0.344,0.198 10 false 2C 4.146,2.125 4.49,2.323 0.344,0.198 10 false 3 4.146,2.625 4.49,2.823 0.344,0.198 10 false 2 4.531,1.052 5.146,1.219 0.615,0.167 10 false EFI NO.2 5.667,0.719 6.01,0.917 0.344,0.198 10 false 24 5.604,0.896 6.01,1.125 0.406,0.229 10 false A57 5.677,1.094 5.979,1.25 0.302,0.156 10 false 25 5.625,1.26 5.948,1.438 0.323,0.177 10 false A56 5.656,2.115 6,2.313 0.344,0.198 10 false 20 5.583,2.281 5.927,2.479 0.344,0.198 10 false B104 6.01,2.281 6.417,2.5 0.406,0.219 10 false IREL 6,1.271 6.438,1.479 0.438,0.208 10 false MREL 6,0.906 6.344,1.104 0.344,0.198 10 false +B 6.24,3.792 6.823,4.083 0.583,0.292 10 false ECM 4.656,4.448 4.917,4.635 0.26,0.188 10 false A 4.104,1.26 4.448,1.458 0.344,0.198 10 false 2D 4.104,2.292 4.448,2.49 0.344,0.198 10 false 2C 4.115,2.823 4.458,3.021 0.344,0.198 10 false 2C

A394583E03
1.583,0.563 1.802,0.781 0.219,0.219 10 false A 1.99,1.656 2.208,1.875 0.219,0.219 10 false *1 2.552,1.667 2.771,1.885 0.219,0.219 10 false *1 0.677,1.896 0.896,2.115 0.219,0.219 10 false 1 1.604,1.896 1.823,2.115 0.219,0.219 10 false 2 0.688,2.156 0.906,2.313 0.219,0.156 10 false i1 0.677,2.333 2.563,2.552 1.885,0.219 10 false No. 1 Injector Assembly 0.698,3.26 0.917,3.417 0.219,0.156 10 false i2 0.688,4.292 0.906,4.448 0.219,0.156 10 false i3 0.698,5.333 0.917,5.49 0.219,0.156 10 false i4 0.688,3.427 2.875,3.677 2.188,0.25 10 false No. 4 Injector Assembly 0.688,4.458 2.927,4.677 2.24,0.219 10 false No. 2 Injector Assembly 0.698,5.5 3.344,5.792 2.646,0.292 10 false No. 3 Injector Assembly 2.479,2.833 2.698,3.052 0.219,0.219 10 false *1 2.469,3.875 2.688,4.094 0.219,0.219 10 false *1 2.469,4.896 2.688,5.115 0.219,0.219 10 false *1 2.479,5.938 2.698,6.156 0.219,0.219 10 false *1 0.281,7.406 1.542,7.646 1.26,0.24 10 false *1: Shielded 6.198,7.042 6.646,7.302 0.448,0.26 10 false ECM 3.396,6.146 5.031,6.552 1.635,0.406 10 false Injector Driver Assembly 3.521,1.01 3.74,1.229 0.219,0.219 10 false 2 3.458,1.219 3.76,1.427 0.302,0.208 10 false B98 3.531,1.802 3.75,2.021 0.219,0.219 10 false 1 3.521,2.469 3.74,2.688 0.219,0.219 10 false 6 3.458,2.667 3.74,2.885 0.281,0.219 10 false B95 3.521,2.875 3.74,3.094 0.219,0.219 10 false 6 3.521,3.5 3.74,3.719 0.219,0.219 10 false 4 3.531,3.906 3.75,4.125 0.219,0.219 10 false 5 3.521,4.552 3.813,4.771 0.292,0.219 10 false 2 3.531,4.938 3.823,5.156 0.292,0.219 10 false 3 3.531,5.583 3.823,5.802 0.292,0.219 10 false 5 3.844,5.115 4.208,5.323 0.365,0.208 10 false IJ4+ 3.833,4.083 4.125,4.302 0.292,0.219 10 false IJ3+ 3.833,3.042 4.125,3.26 0.292,0.219 10 false IJ2+ 3.833,2.667 4.167,2.844 0.333,0.177 10 false IJ1- 3.844,1.99 4.198,2.177 0.354,0.188 10 false IJ1+ 3.833,1.208 4.125,1.427 0.292,0.219 10 false +B 4.198,1.229 4.542,1.448 0.344,0.219 10 false GND 4.198,2.01 4.542,2.198 0.344,0.188 10 false INJF 4.25,2.677 4.625,2.885 0.375,0.208 10 false #10 4.625,4.698 4.917,4.917 0.292,0.219 10 false B97 4.698,4.51 4.99,4.729 0.292,0.219 10 false 3 4.625,4 4.917,4.219 0.292,0.219 10 false B97 4.698,3.802 4.99,4.021 0.292,0.219 10 false 7 4.625,3.344 4.969,3.552 0.344,0.208 10 false B97 4.688,3.146 4.927,3.344 0.24,0.198 10 false 8 4.615,2.667 4.958,2.854 0.344,0.188 10 false B97 4.688,2.479 4.979,2.698 0.292,0.219 10 false 4 4.604,2.01 4.896,2.229 0.292,0.219 10 false B97 4.688,1.813 4.927,2 0.24,0.188 10 false 5 4.615,1.219 4.958,1.438 0.344,0.219 10 false B98 4.688,1.031 4.917,1.219 0.229,0.188 10 false 3 5.646,1.813 5.938,2.031 0.292,0.219 10 false 20 5.573,2.01 5.948,2.198 0.375,0.188 10 false B105 5.646,2.469 5.938,2.688 0.292,0.219 10 false 21 5.573,2.667 5.938,2.885 0.365,0.219 10 false B105 5.646,3.146 5.938,3.365 0.292,0.219 10 false 22 5.563,3.344 5.938,3.5 0.375,0.156 10 false B105 5.635,3.802 5.885,3.969 0.25,0.167 10 false 23 5.563,3.99 5.958,4.208 0.396,0.219 10 false B105 5.646,4.479 5.917,4.656 0.271,0.177 10 false 24 5.573,4.698 5.99,4.917 0.417,0.219 10 false B105 6,1.979 6.396,2.146 0.396,0.167 10 false INJF 6.01,2.656 6.26,2.833 0.25,0.177 10 false #1 6.021,3.333 6.271,3.521 0.25,0.188 10 false #2 6.021,3.979 6.313,4.198 0.292,0.219 10 false #3 6.021,4.688 6.313,4.906 0.292,0.219 10 false #4 3.458,2 3.76,2.208 0.302,0.208 10 false B98 3.458,3.042 3.76,3.25 0.302,0.208 10 false B98 3.469,3.688 3.75,3.906 0.281,0.219 10 false B95 3.469,4.094 3.771,4.302 0.302,0.208 10 false B98 3.458,4.74 3.74,4.958 0.281,0.219 10 false B95 3.448,5.115 3.75,5.323 0.302,0.208 10 false B95 3.49,5.75 3.792,5.958 0.302,0.208 10 false B95 3.833,3.688 4.125,3.906 0.292,0.219 10 false IJ2- 3.844,4.75 4.135,4.969 0.292,0.219 10 false IJ3- 3.833,5.74 4.198,5.948 0.365,0.208 10 false IJ4- 0.667,2.938 0.885,3.156 0.219,0.219 10 false 1 0.677,4 0.896,4.219 0.219,0.219 10 false 1 0.677,5.021 0.896,5.24 0.219,0.219 10 false 1 1.583,2.948 1.802,3.167 0.219,0.219 10 false 2 1.594,4 1.813,4.219 0.219,0.219 10 false 2 1.594,5.021 1.813,5.24 0.219,0.219 10 false 2 4.25,3.354 4.625,3.563 0.375,0.208 10 false #20 4.24,4 4.615,4.208 0.375,0.208 10 false #30 4.24,4.698 4.615,4.906 0.375,0.208 10 false #40

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injector assembly, the ECM needs registration (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.CHECK INJECTOR DRIVER ASSEMBLY (+B VOLTAGE)
a.
A256735C02
1.49,0.229 1.917,0.479 0.427,0.25 1.063,1.542 1.646,1.115 true 2.333,1.542 1.948,1.094 true 0.156,0.135 0.469,0.333 0.313,0.198 10 false *a 1.573,0.281 1.927,0.479 0.354,0.198 10 false B98 0.823,1.542 1.135,1.74 0.313,0.198 10 false +B 2.344,1.542 2.854,1.74 0.51,0.198 10 false GND
*a Front view of wire harness connector
(to Injector Driver Assembly)


Disconnect the injector driver assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B98-2 (+B) - B98-3 (GND) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK INJECTOR DRIVER ASSEMBLY (INJECTOR ASSEMBLY RESISTANCE)

NG

6.INSPECT NO. 2 INTEGRATION RELAY (EDU RELAY)
2.CHECK INJECTOR DRIVER ASSEMBLY (INJECTOR ASSEMBLY RESISTANCE)
a.
A256736C01
1.5,0.5 1.927,0.76 0.427,0.26 1.479,2.365 1.906,2.625 0.427,0.26 1.083,1.354 1.448,1.438 true 1.188,1.885 1.677,1.635 true 1.948,1.635 2.365,1.76 true 1.646,3.948 1.708,3.542 true 1.177,2.854 1.646,3.24 true 0.917,3.719 1.448,3.521 true 2.479,3.76 1.99,3.469 true 2.49,3.052 1.979,3.219 true 0.177,0.156 0.49,0.354 0.313,0.198 10 false *a 1.583,0.552 1.99,0.75 0.406,0.198 10 false B98 1.563,2.406 1.969,2.604 0.406,0.198 10 false B95 0.781,1.26 1.229,1.458 0.448,0.198 10 false IJ1+ 0.875,1.823 1.323,2.021 0.448,0.198 10 false IJ3+ 2.427,1.719 2.875,1.917 0.448,0.198 10 false IJ2+ 2.542,2.958 2.99,3.156 0.448,0.198 10 false IJ4+ 2.552,3.719 3,3.917 0.448,0.198 10 false IJ1- 1.521,3.99 1.969,4.188 0.448,0.198 10 false IJ4- 0.615,3.625 1.063,3.823 0.448,0.198 10 false IJ2- 0.906,2.75 1.354,2.948 0.448,0.198 10 false IJ3-
*a Front view of wire harness connector
(to Injector Driver Assembly)


Disconnect the injector driver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B98-1 (IJ1+) - B95-6 (IJ1-) 20°C (68°F) 0.37 to 0.57 Ω
B98-6 (IJ2+) - B95-4 (IJ2-) 20°C (68°F) 0.37 to 0.57 Ω
B98-5 (IJ3+) - B95-2 (IJ3-) 20°C (68°F) 0.37 to 0.57 Ω
B95-3 (IJ4+) - B95-5 (IJ4-) 20°C (68°F) 0.37 to 0.57 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT INJECTOR ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER ASSEMBLY - ECM)
3.INSPECT INJECTOR ASSEMBLY
a.

Inspect the injector assembly (Click hereEngine / Hybrid System>N04C-VJ (FUEL)>FUEL INJECTOR>INSPECTION).


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (INJECTOR DRIVER ASSEMBLY - INJECTOR ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER ASSEMBLY - ECM)
a.

Disconnect the injector driver assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B97-4 (#10) - B105-21 (#1) Always Below 1 Ω
B97-8 (#20) - B105-22 (#2) Always Below 1 Ω
B97-7 (#30) - B105-23 (#3) Always Below 1 Ω
B97-3 (#40) - B105-24 (#4) Always Below 1 Ω
B97-5 (INJF) - B105-20 (INJF) Always Below 1 Ω
B97-4 (#10) or B105-21 (#1) - Body ground Always 10 kΩ or higher
B97-8 (#20) or B105-22 (#2) - Body ground Always 10 kΩ or higher
B97-7 (#30) or B105-23 (#3) - Body ground Always 10 kΩ or higher
B97-3 (#40) or B105-24 (#4) - Body ground Always 10 kΩ or higher
B97-5 (INJF) or B105-20 (INJF) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT ECM (OUTPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (INJECTOR DRIVER ASSEMBLY - ECM)

5.INSPECT ECM (OUTPUT VOLTAGE)
a.

While idling the engine, check the waveform of the ECM connectors using an oscilloscope.

A316816C02
1.323,0.542 1.688,0.75 0.365,0.208 2.385,0.542 2.75,0.75 0.365,0.208 0.76,1.667 1.354,1.135 true 1.063,1.958 1.448,1.135 true 1.49,1.813 1.5,1.135 true 1.896,1.969 1.583,1.135 true 2.219,1.667 1.635,1.135 true 2.896,1.635 2.896,0.958 true 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 1.354,0.583 1.771,0.792 0.417,0.208 10 false B105 2.427,0.583 2.833,0.781 0.406,0.198 10 false B102 0.521,1.708 0.917,1.875 0.396,0.167 10 false 24(#4) 1.271,1.875 1.781,2.042 0.51,0.167 10 false 22(#2) 0.854,2.021 1.323,2.219 0.469,0.198 10 false 23(#3) 1.781,2.031 2.281,2.198 0.5,0.167 10 false 21(#1) 2.01,1.708 2.573,1.875 0.563,0.167 10 false 20(INJF) 2.771,1.688 3.271,1.854 0.5,0.167 10 false 1(E1) 4.406,0.625 4.719,0.823 0.313,0.198 10 false #1 4.396,0.906 4.708,1.104 0.313,0.198 10 false #3 4.406,1.177 4.719,1.375 0.313,0.198 10 false #4 4.417,1.469 4.729,1.667 0.313,0.198 10 false #2 6.458,0.667 6.771,0.865 0.313,0.198 10 false GND 6.458,0.938 6.771,1.135 0.313,0.198 10 false GND 6.458,1.208 6.771,1.406 0.313,0.198 10 false GND 6.458,1.469 6.771,1.667 0.313,0.198 10 false GND 6.5,3.156 6.813,3.354 0.313,0.198 10 false GND 5.917,0.208 7.146,0.406 1.229,0.198 10 false 5 V/DIV. 5.115,1.594 7.104,1.792 1.99,0.198 10 false 20 msec./DIV. 4.281,2.688 4.896,2.885 0.615,0.198 10 false INJF 5.927,1.875 7.156,2.073 1.229,0.198 10 false 2 V/DIV. 5.156,3.417 7.146,3.615 1.99,0.198 10 false 20 msec./DIV.
*a Component with harness connected
(ECM)
*b Signal Waveform


Standard:
Tester Connection Condition Specified Condition
B105-21 (#1) - B102-1 (E1) Idling with warm engine Correct waveform appears as shown
B105-22 (#2) - B102-1 (E1) Idling with warm engine Correct waveform appears as shown
B105-23 (#3) - B102-1 (E1) Idling with warm engine Correct waveform appears as shown
B105-24 (#4) - B102-1 (E1) Idling with warm engine Correct waveform appears as shown
B105-20 (INJF) - B102-1 (E1) Idling with warm engine Correct waveform appears as shown



Result:
Result Proceed to
#1 to #4 is normal, INJF is abnormal A
#1 to #4 is abnormal, INJF is normal B
#1 to #4 and INJF are normal B



A

REPLACE INJECTOR DRIVER ASSEMBLY

B

6.INSPECT NO. 2 INTEGRATION RELAY (EDU RELAY)
a.

Inspect the No. 2 integration relay (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).

Result:
Proceed to
OK
NG




OK

7.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY - INJECTOR DRIVER ASSEMBLY, BODY GROUND)

NG

REPLACE NO. 2 INTEGRATION RELAY (EDU)

7.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY - INJECTOR DRIVER ASSEMBLY, BODY GROUND)
a.

Remove the No. 2 integration relay from the No. 2 relay block and junction block assembly.


b.

Disconnect the injector driver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2C-4 - B98-2 (+B) Always Below 1 Ω
B98-3 (GND) - Body ground Always Below 1 Ω
2C-4 or B98-2 (+B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK INTEGRATION NO.2 RELAY (NO. 2 INTEGRATION RELAY - BATTELY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK INTEGRATION NO.2 RELAY (NO. 2 INTEGRATION RELAY - BATTELY)
a.

Remove the No. 2 integration relay from the No. 2 relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2C-2 - 2D-4 Always Below 1 Ω
2E-1 - Battery Always Below 1 Ω
2D-3 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY - ECM,BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY - ECM,BODY GROUND)
a.

Remove the No. 2 integration relay from the No. 2 relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2C-3 - B104-20 (IREL) Always Below 1 Ω
2C-2 - A56-20 (MREL) Always Below 1 Ω
B102-11 (E01) - Body ground Always Below 1 Ω
2C-3 or B104-20 (IREL) - Body ground Always 10 kΩ or higher
2C-2 or A56-20 (MREL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR