Home › Engine / Hybrid System › N04C-VJ (ENGINE CONTROL) › ECD SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _096807 N04C-VJ ENGINE CONTROL _0454116 ECD SYSTEM C

N04C-VJ ENGINE CONTROL  ECD SYSTEM  P1458  EGR Actuator Minor Malfunction  P1459  EGR Actuator Major Malfunction  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1458 EGR Actuator Minor Malfunction The EGR valve assembly outputs an abnormal signal a certain amount of times while the engine is running.
(1 trip detection logic)
·

Open or short in EGR valve assembly circuit

·

EGR valve assembly

·

ECM


Comes on DTC stored
P1459 EGR Actuator Major Malfunction The EGR valve assembly outputs an abnormal signal a certain amount of times while the engine is running.
(1 trip detection logic)
·

Open or short in EGR valve assembly circuit

·

EGR valve assembly

·

ECM


Comes on DTC stored

WIRING DIAGRAM

A483979E05
0.729,1.417 1.49,1.604 0.76,0.188 10 false EFI NO.1 1.771,1.24 2.625,1.49 0.854,0.25 10 false ACT PWR 1.615,0.531 1.865,0.76 0.25,0.229 10 false 3 1.625,0.854 1.823,1.052 0.198,0.198 10 false 1 2.469,0.51 2.708,0.729 0.24,0.219 10 false 5 2.458,0.854 2.667,1.083 0.208,0.229 10 false 2 3.417,0.51 3.604,0.708 0.188,0.198 10 false 4 3.417,1.188 3.646,1.406 0.229,0.219 10 false 1 3.646,0.604 4.021,0.771 0.375,0.167 10 false B+ 3.635,1.292 4.042,1.5 0.406,0.208 10 false E 3.552,1.573 4.146,1.771 0.594,0.198 10 false B48 3.552,1.75 5.531,2.396 1.979,0.646 10 false EGR Valve Assembly 6.135,3.219 6.458,3.427 0.323,0.208 10 false +B 6.135,3.813 6.583,4.01 0.448,0.198 10 false MREL 6.365,4.313 6.896,4.708 0.531,0.396 10 false ECM 5.75,3.823 6.094,3.99 0.344,0.167 10 false A56 5.792,3.615 6.031,3.813 0.24,0.198 10 false 25 5.75,3.229 6.052,3.396 0.302,0.167 10 false A57 5.792,3.031 5.99,3.219 0.198,0.188 10 false 24 4.615,3.375 5.25,3.604 0.635,0.229 10 false EFI NO.2 4.208,3.031 4.427,3.198 0.219,0.167 10 false 4 4.177,3.229 4.479,3.385 0.302,0.156 10 false 2D 4.219,3.615 4.427,3.781 0.208,0.167 10 false 2 3.385,4.083 3.698,4.271 0.313,0.188 10 false EFI 2.25,3.375 2.906,3.604 0.656,0.229 10 false EFI-MAIN 1.896,2.698 2.104,2.875 0.208,0.177 10 false 1 1.854,2.875 2.094,3.063 0.24,0.188 10 false 2D 1.896,3.052 2.125,3.229 0.229,0.177 10 false 1 1.865,3.24 2.125,3.406 0.26,0.167 10 false 2E 1.896,3.646 2.135,3.823 0.24,0.177 10 false 3 1.865,3.823 2.115,4.031 0.25,0.208 10 false 2D 2.469,4.427 4.302,4.646 1.833,0.219 10 false No. 2 Integration Relay 1.188,3.417 1.521,3.583 0.333,0.167 10 false P/I 0.354,3.385 0.979,3.76 0.625,0.375 10 false R/B No. 2-B 0.385,4.167 1.052,4.396 0.667,0.229 10 false FL MAIN 0.583,4.906 1.219,5.135 0.635,0.229 10 false Battery 4.125,5.031 6.063,5.271 1.938,0.24 10 false : CAN Communication Line 4.177,3.833 4.479,3.99 0.302,0.156 10 false 2D 4.271,0.604 4.677,0.813 0.406,0.208 10 false CANH 6.135,0.573 6.542,0.781 0.406,0.208 10 false CAN+ 6.146,1.198 6.552,1.406 0.406,0.208 10 false CAN- 4.281,1.198 4.688,1.406 0.406,0.208 10 false CANL 5.708,1.208 6.177,1.385 0.469,0.177 10 false B104 5.708,0.594 6.177,0.771 0.469,0.177 10 false B104 5.771,0.385 5.969,0.573 0.198,0.188 10 false 12 5.833,1.01 6.031,1.198 0.198,0.188 10 false 6 4.75,0.417 4.948,0.604 0.198,0.188 10 false 5 4.76,1.031 4.958,1.219 0.198,0.188 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.CHECK EGR VALVE ASSEMBLY (POWER SOURCE)
a.
A227775C05
1.469,0.292 1.958,0.583 0.49,0.292 1.438,1.396 1.031,1.75 false 0.844,1.76 1.083,1.948 0.24,0.188 10 false +B 0.135,0.115 0.427,0.385 0.292,0.271 10 false *a 1.604,0.365 1.99,0.594 0.385,0.229 10 false B48
*a Front view of wire harness connector
(to EGR Valve Assembly)


Disconnect the EGR valve assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B48-4 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS OR CONNECTOR (EGR VALVE ASSEMBLY - BODY GROUND)

NG

8.CHECK HARNESS OR CONNECTOR (ACT PWR RELAY - NO. 2 INTEGRATION RELAY)
2.CHECK HARNESS OR CONNECTOR (EGR VALVE ASSEMBLY - BODY GROUND)
a.

Disconnect the EGR valve assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B48-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT EGR VALVE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EGR VALVE ASSEMBLY - BODY GROUND)

3.INSPECT EGR VALVE ASSEMBLY
a.

Check the EGR valve assembly

Click hereEngine / Hybrid System>N04C-VJ (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION

Result:
Proceed to
OK
NG




OK

4.CLEAR DTC

NG

4.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.


Result:
Proceed to
NEXT



NEXT

5.CHECK OTHER DTC OUTPUT
5.CHECK OTHER DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Rear the DTCs.


Result:
Result Proceed to
DTC P1458 or P1459 is output A
DTC is not output B



A

6.REPLACE ECM

B

6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CHECK OTHER DTC OUTPUT
7.CHECK OTHER DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Rear the DTCs.


Result:
Result Proceed to
DTC is not output A
DTC P1458 or P1459 is output B



A

END

B

8.CHECK HARNESS OR CONNECTOR (ACT PWR RELAY - NO. 2 INTEGRATION RELAY)
a.

Remove the ACT PWR relay from the No. 2 relay block and junction block assembly.


b.

Remove the No. 2 integration relay from the No. 2 relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (ACT PWR relay holder) - 2D-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.INSPECT RELAY (ACT PWR RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ACT PWR RELAY - NO. 2 INTEGRATION RELAY)

9.INSPECT RELAY (ACT PWR RELAY)

Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS OR CONNECTOR (ACT PWR RELAY - EGR VALVE ASSEMBLY)

NG

REPAIR OR REPLACE RELAY (ACT PWR RELAY - NO. 2 INTEGRATION RELAY)

10.CHECK HARNESS OR CONNECTOR (ACT PWR RELAY - EGR VALVE ASSEMBLY)
a.

Remove the ACT PWR relay from the No. 2 relay block and junction block assembly.


b.

Remove the No. 2 integration relay from the No. 2 relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (ACT PWR relay holder) - B48-4 (+B) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE RELAY (ACT PWR RELAY - EGR VALVE ASSEMBLY)