Home › Engine / Hybrid System › N04C-VJ (ENGINE CONTROL) › ECD SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _096807 N04C-VJ ENGINE CONTROL _0454116 ECD SYSTEM C

N04C-VJ ENGINE CONTROL  ECD SYSTEM  P1604  Startability Malfunction  


DESCRIPTION

This DTC is stored if the engine does not start or continues to crank without starting for certain period of time. This DTC is also stored if the vehicle has run out of fuel. It is necessary to check whether there was enough fuel in the fuel tank before inspection.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1604 Startability Malfunction
1.

Both conditions are met for 2 seconds or more*1 (1 trip detection logic):

*1: The time required for DTC detection may be as much as 30 seconds depending on the engine coolant temperature and atmospheric pressure.

-

STA signal is input to the ECM.

-

Engine speed is 500 rpm or less.


2.

After starting the engine (engine speed is 500 rpm or more), the engine speed drops to 200 rpm or less within 2 seconds*2 (1 trip detection logic).

*2: This DTC may be stored when the engine stalls due to clutch misoperation.


·

Battery

·

Irregular fuel

·

Lack of fuel

·

Injection or supply pump assembly

(suction control valve)

·

Injector assembly

·

Diesel fuel filter assembly

·

Injector driver

·

Engine coolant temperature sensor

·

Intake system

·

Exhaust system

·

Engine damaged, seized up

·

Loss of compression

·

Fuel pressure sensor

·

EGR system

·

Diesel throttle system


Does not come on DTC stored

Related Data List
DTC No. Data List
P1604
·

MAP

·

MAF

·

Intake Air

·

Coolant Temp

·

Battery Voltage

·

Starter Signal

·

Engine Speed of Cyl #1 (to #4)

·

Target Common Rail Pressure

·

Fuel Press

·

Common Rail Pres Sens 2

·

Target Pump SCV Current

·

Injection Feedback Val #1 (to #4)

·

Injection Volume

·

Main Injection Period

·

Actual Throttle Position

·

Throttle Motor Duty #1

·

Target EGR Position

·

Actual EGR Valve Pos.

·

EGR Close Lrn. Status



CAUTION / NOTICE / HINT

HINT:
·

In contrast to normal malfunction diagnosis for components, circuits and systems, DTC P1604 is used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as starting difficulty.

As these DTCs can be stored as a result of certain user actions, even if these DTCs are output, if the customer makes no mention of problems, clear these DTCs without performing any troubleshooting and return the vehicle to the customer.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.

·

When confirming the freeze frame data, be sure to check all 5 data sets of freeze frame data.

·
A301856E29
2.24,0.938 3.083,1.167 0.844,0.229 10 false 0.5 seconds 0.344,0.938 1.188,1.167 0.844,0.229 10 false 0.5 seconds 1.323,0.927 2.167,1.156 0.844,0.229 10 false 0.5 seconds 0.406,2.813 2.385,3.031 1.979,0.219 10 false Freeze frame data recorded 2.344,0.198 3.323,0.406 0.979,0.208 10 false DTC is stored 0.229,2.5 0.458,2.708 0.229,0.208 10 false 1 1.177,2.521 1.406,2.729 0.229,0.208 10 false 2 2.125,2.51 2.354,2.719 0.229,0.208 10 false 3 2.729,2.698 2.958,2.906 0.229,0.208 10 false 4 3.063,2.49 3.292,2.698 0.229,0.208 10 false 5

The fourth set of freeze frame data is the data recorded when the DTC is stored.



In order to start the engine, the starting system, fuel system and the components related to compression must be functioning properly.



The cause of the problem can be narrowed down by checking if the engine cranks normally.



Starting system (when cranking is abnormal)


a.

The engine cannot be started if a sufficient cranking speed cannot be obtained. The following are possible causes of an insufficient cranking speed.

i.

Problem with the battery (Cranking speed is low).


ii.

Problem with the starter (Cranking speed is low).




Fuel system (when cranking is normal)


a.

The engine cannot be started if fuel is not supplied. A minimum fuel pressure of 25000 kPa or higher must be supplied to start the engine. The following are possible causes of insufficient fuel pressure.

i.

Fuel line clog.


ii.

Lack of fuel.


iii.

Fuel frozen.


iv.

Low quality fuel.


v.

Air in fuel pipe.


vi.

Diesel fuel filter assembly clog.


vii.

Problem with injection or supply pump assembly.


viii.

Problem with common rail assembly.


ix.

Problem with injector assemblies.




Engine assembly


a.

There may be a problem with the engine unit itself if there is no problem with cranking, the fuel system.

i.

Engine friction too high.


ii.

Insufficient compression.




PROCEDURE

1.READ OUTPUT DTC (RECORD STORED DTC AND FREEZE FRAME DATA) (PROCEDURE 1)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Record the stored DTCs and freeze frame data.

HINT:

Freeze frame data shows the actual engine conditions when engine starting trouble occurred.



Result:
Proceed to
NEXT



NEXT

2.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1604)
2.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1604)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
P1604 is output A
P1604 and other DTCs are output B


HINT:

If any DTCs other than DTC P1604 are output, troubleshoot those DTCs first.




A

3.TAKE SNAPSHOT DURING STARTING AND IDLING (PROCEDURE 3)

B

3.TAKE SNAPSHOT DURING STARTING AND IDLING (PROCEDURE 3)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.


e.

Take a snapshot of the following Data List items with the GTS during "ignition switch ON (5 seconds) → Starting → Idling (10 seconds)".


Result:
Proceed to
NEXT



NEXT

4.DETERMINE CAUSE OF PROBLEM (CHECK FREEZE FRAME DATA AND SNAPSHOT)
4.DETERMINE CAUSE OF PROBLEM (CHECK FREEZE FRAME DATA AND SNAPSHOT)
a.

Determine the cause of the problem based on the freeze frame data recorded in procedure 1 and the Data List values recorded when starting the engine in procedure 3.

Coolant Temp
Judgment of Data List Values Problem Cause Normal Condition Diagnosis Note
"Coolant Temp" in freeze frame data is below 35°C (95°F) Engine starting trouble which occurred with cold engine -
·

The engine coolant temperature is 60 to 90°C (140 to 194°F) after warming up the engine.

·

Normally, "Coolant Temp" is the same as the outside air temperature after an overnight engine soak.

·

Engine starting trouble with a cold engine occurs when the engine coolant temperature sensor is malfunctioning.


"Coolant Temp" in freeze frame data is below 35°C (95°F).
Currently, no engine starting trouble (cranking time less than 4 seconds) after warming up engine ("Coolant Temp" is 60°C (140°F) or higher).
Engine starting trouble which only occurs with cold engine

Engine Speed
Judgment of Data List Values Problem Cause Normal Condition Diagnosis Note
"Engine Speed" in freeze frame data is less than 120 rpm Engine starting trouble may have occurred because engine speed was too low
·

During cranking: 120 to 400 rpm

·

Idling with warm engine: 550 to 650 rpm


·

The battery may be fully depleted or the battery terminals may be loose.

·

The viscosity of the engine oil may be inappropriate (low viscosity oil is not used).


"Engine Speed" in Data List is less than 120 rpm when cranking engine

Battery Voltage
Judgment of Data List Values Problem Cause Normal Condition Diagnosis Note
"Battery Voltage" in freeze frame data is below 6 V Engine starting trouble may have occurred because battery is fully depleted During cranking: 6 V or higher The battery may be fully depleted or the battery terminals may be loose.
"Battery Voltage" in Data List is below 6 V when cranking engine

Fuel Press
Judgment of Data List Values Problem Cause Normal Condition Diagnosis Note
"Fuel Press" in freeze frame data is below 10000 kPa Problem injection or supplying fuel to supply pump assembly (low pressure side)
·

Ran out of fuel, air in fuel, fuel frozen (in this case, values of "Fuel Temperature" and "Coolant Temp" in freeze frame data are low)

·

Fuel filter clog, fuel line clog (low pressure side) or fuel leak

·

Feed pump (in injection or supply pump assembly) malfunctioning


When in a stable condition such as when the engine is idling after being warmed up, the fuel pressure is within +/-5000 kPa of the target fuel pressure Disconnect the inlet hose from the injection or supply pump assembly (low pressure side), operate the hand pump and check that fuel is being supplied.
"Fuel Press" in Data List is less than 10000 kPa from the value of Fuel Press when cranking started
"Fuel Press" in freeze frame data is below 25000 kPa Problem supplying fuel to injection or supply pump assembly (low pressure side) or problem on high pressure side
·

Injection or supply pump assembly (SCV operation malfunction)

·

Common rail Assembly

·

Fuel injector

·

Fuel line clog (high pressure side), fuel leak


When in a stable condition such as when the engine is idling after being warmed up, the fuel pressure is within +/-5000 kPa of the target fuel pressure
·

For startup at least 25000 kPa of fuel pressure is needed (Take care there is a response lag when the pressure rise)

·

If the fuel pressure is 10000 kPa or lower (when starting with an engine coolant temperature of 0°C (32°F) or lower, 15000 kPa or lower), fuel injection is stopped.


"Fuel Press" in Data List is below Target Common Rail Pressure by 15000 kPa or more
"Fuel Press" in Data List increases to a value that is higher than Target Common Rail Pressure immediately after cranking, and, remains higher than Target Common Rail Pressure
·

Injector (fuel injection problem caused by air in injector)

·

Problem with injection system


When in a stable condition such as when the engine is idling after being warmed up, the fuel pressure is within +/-5000 kPa of the target fuel pressure
·

If there is air in the injectors for all cylinders, fuel cannot be injected.

·

If there is an injection system problem related to 2 or more cylinders, fuel delivery and injection control are stopped.

·

When the EDU circuit has a malfunction (e.g. an No. 2 integration relay or fuse malfunction), the ECM cannot perform diagnosis of malfunctions and DTCs are not stored as voltage is unstable during cranking. Also, an excess amount of fuel is supplied by the injection or supply pump assembly and "Fuel Press" becomes larger than "Target Common Rail Pressure" as fuel injection cannot be performed even though a fuel injection signal is output due to a failure to detect malfunctions at engine start.



Injection Feedback Val #1(to #4)
Judgment of Data List Values Problem Cause Normal Condition Diagnosis Note
"Injection Feedback Val #1 (to #4)" in freeze frame data is more than 2.0 mm3/st Injector assembly malfunction or compression problem -2.0 to 2.0 mm3/st If an injector assembly is malfunctioning, even though the engine starts, idling is rough.
"Injection Feedback Val #1 (to #4)" in Data List is more than 2.0 mm3/st when idling

Injection Volume
Judgment of Data List Values Problem Cause Normal Condition Diagnosis Note
"Injection Volume" in Data List is 10 mm3/st or less and "Injection Feedback Val #1 (to #4)" is +2.0 mm3/st or less when idling after warming up engine Injector assemblies of all cylinders malfunctioning - -

Main Injection Period
Judgment of Data List Values Problem Cause Normal Condition Diagnosis Note
"Main Injection Period" in freeze frame data or Data List is 0 μs
·

Injection or supply pump assembly (when SCV has open or short circuit, fuel supply from pump stops)

·

Problem with injection system (injector circuit is open (2 cylinders or more) or injector driver is malfunctioning)

·

Engine speed 60 rpm or less

·

ECM malfunction


- Indicates that fuel injection control has stopped.


Result:
Proceed to
NEXT



NEXT