Home › Engine / Hybrid System › N04C-VJ (ENGINE CONTROL) › ECD SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _096807 N04C-VJ ENGINE CONTROL _0454116 ECD SYSTEM J

N04C-VJ ENGINE CONTROL  ECD SYSTEM  Engine Difficult to Start or Stalling  


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injection or supply pump assembly, the ECM needs initialization (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injector assembly, the ECM needs registration (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



HINT:
·

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle's age. Do not assume the vehicle is normal when the Data List outputs standard values. There may be concealed factors of the malfunction.

·

If the vehicle runs out of fuel while the engine is operating, there is a chance that the engine may be difficult to restart after fuel is refilled.



PROCEDURE

1.CHECK DTC OUTPUT (RELATED TO ENGINE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.


d.

Read the DTCs.


Result:
Result Proceed to
No output A
DTCs related to engine B



A

2.CHECK ID CODE

B

2.CHECK ID CODE
a.

Check that the ID code is registered correctly.

Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION


Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE CRANKING CONDITION

NG

REGISTRATION ID CODE

3.CHECK ENGINE CRANKING CONDITION
a.

Check the engine cranking condition.


b.

Compare the cranking condition with that of a normal engine of the same model, and carefully check if there is any difference between them.

OK:

Engine cranking condition is normal.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (FUEL PRESS)

NG

CHECK AND REPLACE BATTERY, CHARGING SYSTEM, STARTER ASSEMBLY AND STARTING SYSTEM

4.READ VALUE USING GTS (FUEL PRESS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.


e.

Read the value.

Standard:
Item Inspection Condition Reference Value
Fuel Press Cranking, and engine coolant temperature 0°C (32°F) or more 25000 kPa or more



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER ASSEMBLY TERMINAL VOLTAGE)

NG

BLEED AIR FROM FUEL SYSTEM

5.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER ASSEMBLY TERMINAL VOLTAGE)
a.
A401620C01
1.5,0.25 1.917,0.5 0.417,0.25 1.333,1.833 1.667,1.083 false 2.167,1.833 1.917,1.083 false 1.604,0.302 2.063,0.5 0.458,0.198 10 false B98 0.167,0.135 0.625,0.333 0.458,0.198 10 false *a 1.208,1.917 1.667,2.115 0.458,0.198 10 false +B 2.125,1.917 2.583,2.115 0.458,0.198 10 false GND
*a Front view of wire harness connector
(to Injector Driver Assembly)


Disconnect the injector driver assembly connectors.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B98-2 (+B) - B98-3 (GND) Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

6.CHECK IF INITIAL COMBUSTION OCCURS

NG

REPAIR OR REPLACE INJECTOR DRIVER (INJECTOR DRIVER ASSEMBLY)

6.CHECK IF INITIAL COMBUSTION OCCURS
a.

Check if initial combustion occurs.


Result:
Result Proceed to
No initial combustion A
Initial combustion occurs B



A

7.CHECK IF FUEL IS BEING SUPPLIED TO INJECTION OR SUPPLY PUMP ASSEMBLY

B

8.CHECK AIR INTAKE SYSTEM AND EXHAUST SYSTEM
7.CHECK IF FUEL IS BEING SUPPLIED TO INJECTION OR SUPPLY PUMP ASSEMBLY
a.

Disconnect the inlet hose from the injection or supply pump assembly.


b.

Operate the priming pump and check that fuel is being supplied to the injection or supply pump assembly.

OK:

Fuel is properly supplied to the injection or supply pump assembly when the priming pump is operated.



Result:
Proceed to
OK
NG



OK

8.CHECK AIR INTAKE SYSTEM AND EXHAUST SYSTEM

NG

CHECK AND REPLACE FUEL PIPE CLOGGING (INCLUDING FUEL FREEZING) (FUEL TANK - SUPPLY PUMP)

8.CHECK AIR INTAKE SYSTEM AND EXHAUST SYSTEM

Result:
Proceed to
OK
NG



OK

9.INSPECT EXHAUST RETARDER ASSEMBLY

NG

REPAIR OR REPLACE LOCATIONS WHERE MALFUNCTIONS EXIST

9.INSPECT EXHAUST RETARDER ASSEMBLY
a.

Inspect the exhaust retarder assembly.


Result:
Proceed to
OK
NG



OK

10.READ VALUE USING GTS (FUEL PRESS AND INJECTION VOLUME)

NG

REPLACE EXHAUST RETARDER ASSEMBLY

10.READ VALUE USING GTS (FUEL PRESS AND INJECTION VOLUME)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

Enter the following menus in order and read the values.

·

Fuel Press

·

Injection Volume


NOTICE:
·

It is difficult to indicate a clear standard value (judgment value) for Data List value since there is significant variation due to minor difference of measurement, difference in the measuring environment, aging variation of the vehicle, etc.

It is possible that a malfunction may be present even if measured values are within the standard range.

·

In the event of a problem with intricate symptoms such as hesitation and rough idling, collect sample data from another vehicle of the same model operating under identical conditions in order to reach an overall judgment by comparing all the items in the Data List.

·

The actual common rail pressure is listed here as a standard value, but the standard value will vary depending on the vehicle condition and model.

When judging the fuel pressure, check that the target common rail pressure and actual common rail pressure follow reliably with the accelerator position and engine speed at a constant setting.

However, the target common rail pressure and actual common rail pressure will not follow immediately after operating the accelerator pedal.



Standard:
Item Engine Speed* Reference Value
Fuel Press Idling 20000 to 30000 kPa
2800 rpm 110000 to 120000 kPa
Injection Volume Idling 5 to 12 mm3/st
2800 rpm 9 to 17 mm3/st


HINT:

*: The shift lever should be in the neutral position, and the A/C switch and all accessory switches should be OFF.



Result:
Proceed to
OK
NG



OK

11.CHECK CYLINDER COMPRESSION PRESSURE

NG

14.INSPECT ECM (THW TERMINAL VOLTAGE)
11.CHECK CYLINDER COMPRESSION PRESSURE
a.

Check the cylinder compression pressure (Click here Engine / Hybrid System>N04C-VJ (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION).


Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - INJECTOR DRIVER ASSEMBLY)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

12.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - INJECTOR DRIVER ASSEMBLY)
a.

Check the wire harness between the injector assembly and injector driver assembly (INJ terminal).

i.

Disconnect the injector assembly connectors.


ii.

Disconnect the injector driver assembly connectors.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B98-1(IJ1+) - i1-2 Always Below 1 Ω
B95-6(IJ1-) - i1-1 Always Below 1 Ω
B98-6(IJ2+) - i2-2 Always Below 1 Ω
B95-4(IJ2-) - i2-1 Always Below 1 Ω
B98-5(IJ3+) - i3-2 Always Below 1 Ω
B95-2(IJ3-) - i3-1 Always Below 1 Ω
B95-3(IJ4+) - i4-2 Always Below 1 Ω
B95-5(IJ4-) - i4-1 Always Below 1 Ω
B98-1(IJ1+) or i1-2 - Body ground Always 10 kΩ or higher
B95-6(IJ1-) or i1-1 - Body ground Always 10 kΩ or higher
B98-6(IJ2+) or i2-2 - Body ground Always 10 kΩ or higher
B95-4(IJ2-) or i2-1 - Body ground Always 10 kΩ or higher
B98-5(IJ3+) or i3-2 - Body ground Always 10 kΩ or higher
B95-2(IJ3-) or i3-1 - Body ground Always 10 kΩ or higher
B95-3(IJ4+) or i4-2 - Body ground Always 10 kΩ or higher
B95-5(IJ4-) or i4-1 - Body ground Always 10 kΩ or higher



iv.

Reconnect the injector assembly connectors.


v.

Reconnect the injector driver assembly connectors.



Result:
Proceed to
OK
NG



OK

13.PERFORM ACTIVE TEST USING GTS (CONTROL THE CYLINDER #1 TO #4 FUEL CUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.PERFORM ACTIVE TEST USING GTS (CONTROL THE CYLINDER #1 TO #4 FUEL CUT)
HINT:

Use this Active Test to determine the malfunctioning cylinder.


a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1 to #4 Fuel Cut.

HINT:
·

If the engine idle speed does not change when a fuel injector is disabled, the cylinder being tested is malfunctioning.

·

If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.




Result:
Result Proceed to
Engine idling condition becomes unstable A
Engine idling condition does not change B



A

REPLACE INJECTOR DRIVER ASSEMBLY

B

14.INSPECT ECM (THW TERMINAL VOLTAGE)
a.
A261727C01
1.333,0.25 1.76,0.49 0.427,0.24 1.833,0.25 2.26,0.49 0.427,0.24 1.625,0.802 1.417,1.74 false 2.177,0.885 2.333,1.75 false 0.094,0.094 0.292,0.25 0.198,0.156 10 false *a 1.396,0.302 1.865,0.51 0.469,0.208 10 false B105 2.208,1.823 2.938,1.979 0.729,0.156 10 false 14(E2) 1.25,1.833 1.906,1.99 0.656,0.156 10 false 9(THW) 1.906,0.302 2.375,0.51 0.469,0.208 10 false B104
*a Component with harness connected
(ECM)


Start the engine.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B105-9(THW) - B104-14(E2) Idling, engine coolant temperature between 70 and 90°C (158 and 194°F) 0.4 to 0.7 V



Result:
Proceed to
OK
NG



OK

15.INSPECT CRANKSHAFT POSITION SENSOR

NG

18.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
15.INSPECT CRANKSHAFT POSITION SENSOR
a.
A256050C04
2.323,0.344 2.813,0.635 0.49,0.292 2.583,0.938 2.302,1.719 false 2.635,0.938 2.865,1.719 false 2.406,0.417 2.792,0.583 0.385,0.167 10 false B103 2.74,1.76 3.417,1.958 0.677,0.198 10 false 7 (NE+) 2.156,1.781 2.74,2.021 0.583,0.24 10 false 8 (NE-) 3.104,3.688 3.427,3.833 0.323,0.146 10 false GND 0.094,3.646 0.521,3.865 0.427,0.219 10 false NE+ 0.125,0.104 0.333,0.271 0.208,0.167 10 false *a 1.219,4.385 2.292,4.583 1.073,0.198 10 false 20 msec./DIV. 2.646,2.479 3.354,2.75 0.708,0.271 10 false 5 V/DIV.
*a Component with harness connected
(ECM)


While idling the engine, check the waveform between the specified terminals of the ECM connector using an oscilloscope.

HINT:
·

The higher the engine speed becomes, the larger the amplitude.

·

The higher the engine speed becomes, the shorter the cycle.

·

A DTC may be detected due to noise.



Standard:
Tester Connection Condition Specified Condition
B103-7 (NE+) - B103-8 (NE-) Engine idling Correct waveform appears as shown



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (STARTER RELAY - ECM)

NG

19.INSPECT CRANKSHAFT POSITION SENSOR
16.CHECK HARNESS AND CONNECTOR (STARTER RELAY - ECM)
a.

Disconnect the ECM connector.


b.

Remove the starter relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 1 - A57-6 (STA) Always Below 1 Ω
ST relay terminal 1 or A57-6 (STA) - Body ground Always 10 kΩ or higher



d.

Reinstall the starter relay.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

17.INSPECT COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.INSPECT COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)
a.
A261727C02
1.344,0.25 1.719,0.51 0.375,0.26 1.833,0.25 2.208,0.51 0.375,0.26 1.688,0.729 1.333,1.74 false 1.688,0.875 1.917,1.75 false 2.188,0.885 2.917,1.75 false 0.5,1.75 1.521,0.875 false 0.104,0.094 0.302,0.25 0.198,0.156 10 false *a 1.385,0.313 1.844,0.458 0.458,0.146 10 false B105 0.188,1.802 0.792,1.958 0.604,0.156 10 false 16(PCR1) 2.813,1.813 3.313,1.979 0.5,0.167 10 false 14(E2) 1.094,1.813 1.75,1.969 0.656,0.156 10 false 2(PCR2) 1.875,0.313 2.333,0.458 0.458,0.146 10 false B104 1.729,1.813 2.385,1.969 0.656,0.156 10 false 14(E21)
*a Component with harness connected
(ECM)


Start the engine.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B105-16(PCR1) - B104-14(E2) Idling 1.6 to 2.0 V
B105-2(PCR2) - B105-14(E21) Idling 1.1 to 1.5 V



Result:
Proceed to
OK
NG



OK

22.CHECK FUEL INJECTION SYSTEM

NG

20.INSPECT COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)
18.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)

NG

19.INSPECT CRANKSHAFT POSITION SENSOR
a.

Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - CRANKSHAFT POSITION SENSOR)

NG

20.INSPECT COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)
a.

Inspect the fuel pressure sensor connector.

Click hereEngine / Hybrid System>N04C-VJ (FUEL)>COMMON RAIL>INSPECTION


Result:
Proceed to
OK
NG



OK

21.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

NG

REPLACE COMMON RAIL ASSEMBLY

21.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the fuel pressure sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B104-13(VC) - B93-1(VC1) Always Below 1 Ω
B105-16(PCR1) - B93-2(PCR1) Always Below 1 Ω
B104-14(E2) - B93-3(E1) Always Below 1 Ω
B105-14(E21) - B93-4(E2) Always Below 1 Ω
B105-2(PCR2) - B93-5(PCR2) Always Below 1 Ω
B105-13(VC2) - B93-6(VC2) Always Below 1 Ω
B104-13(VC) or B93-1(VC1) - Body ground Always 10 kΩ or higher
B105-16(PCR1) or B93-2(PCR1) - Body ground Always 10 kΩ or higher
B104-14(E2) or B93-3(E1) - Body ground Always 10 kΩ or higher
B105-14(E21) or B93-4(E2) - Body ground Always 10 kΩ or higher
B105-2(PCR2) or B93-5(PCR2) - Body ground Always 10 kΩ or higher
B105-13(VC2) or B93-6(VC2) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connectors.


e.

Reconnect the fuel pressure sensor connector.


Result:
Proceed to
OK
NG



OK

22.CHECK FUEL INJECTION SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.CHECK FUEL INJECTION SYSTEM

b.

Check that the malfunction has disappeared.


Result:
Result Proceed to
Malfunction does not disappear A
Malfunction disappears B



A

B

END