Home › Engine / Hybrid System › N04C-VJ (ENGINE CONTROL) › ECD SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _096807 N04C-VJ ENGINE CONTROL _0454116 ECD SYSTEM C

N04C-VJ ENGINE CONTROL  ECD SYSTEM  P1605  Rough Idling  


DESCRIPTION

This DTC is stored when the speed of a specific cylinder becomes low and the idle speed becomes unstable. This DTC is also stored if the vehicle runs out of fuel. Be sure to check whether there is enough fuel in the fuel tank before inspection.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1605 Rough Idling When the accelerator pedal is fully closed and the engine is idling, the speed of a specific cylinder is low for 2 to 10 seconds (1 trip detection logic).
·

Injector assembly

·

Injector compensation code

·

Fuel leak

·

Intake air system leakage

·

Intake air system blockage

·

EGR system

·

Throttle valve system

·

Injection or supply pump assembly

(suction control valve)

·

Low quality fuel

·

Diesel fuel filter assembly air bleed problem

·

Accessory problem (A/C, generator, etc.)

·

Engine assembly

·

ECM


Does not come on DTC stored

Related Data List
DTC No. Data List
P1605
·

Target Idle Engine Speed

·

Engine Speed

·

MAP

·

MAF

·

Coolant Temp

·

Battery Voltage

·

Engine Speed of Cyl #1 (to #4)

·

Intake Air

·

Target Common Rail Pressure

·

Fuel Press

·

Common Rail Pres Sens 2

·

Target Pump SCV Current

·

Injection Feedback Val #1 (to #4)

·

Injection Volume

·

Actual Throttle Position

·

Target EGR Valve Pos.

·

Actual EGR Valve Pos.

·

EGR Close Lrn. Status

·

EGR Close Lrn. Val.



CAUTION / NOTICE / HINT

In order for idling to be stable, fuel system operation and compression sufficient to maintain the target idling speed are necessary.



Fuel system


a.

The following malfunctions may be present in the fuel system.

i.

Fuel leakage.


ii.

Problem with injector assemblies.


iii.

Problem with injection or supply pump assembly.


iv.

Air in fuel pipe.




Engine assembly


a.

The following malfunctions may be present in the engine assembly.

i.

Insufficient compression.




HINT:
·

In contrast to normal malfunction diagnosis for components, circuits and systems, DTCs P1603 and P1605 are used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as engine stall.

As these DTCs can be stored as a result of certain user actions, even if these DTCs are output, if the customer makes no mention of problems, clear these DTCs without performing any troubleshooting and return the vehicle to the customer.

·

If any other DTCs are output, perform troubleshooting for those DTCs first.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data.



PROCEDURE

1.DTC OUTPUT (RECORD STORED DTC AND FREEZE FRAME DATA (PROCEDURE 1))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Record the stored DTC and freeze frame data.

HINT:

This freeze frame data shows the actual engine conditions when air fuel ratio too rich trouble occurred.



Result:
Proceed to
NEXT



NEXT

2.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1605)
2.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1605)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
P1605 is output A
P1605 and other DTCs are output B


HINT:

If any DTCs other than P1605 are output, troubleshoot those DTCs first.




A

B