| Malfunction Condition | Main Trouble Areas | Related Trouble Areas |
|---|---|---|
| Rough idling or shuddering due to abnormal combustion | Injector malfunctions
- Injector assembly sliding malfunction - Injector assembly stuck closed - Injector assembly stuck open - Deposit in injector assembly - Injector assembly circuit malfunction |
·
Injector compensation code ·
Fuel leak ·
Engine mounting insulator ·
Intake air system leak ·
Intake air system blockage ·
EGR system ·
Throttle valve system ·
Injection or supply pump assembly ·
Pressure limiter (built into common rail assembly) ·
Fuel pressure sensor (built into common rail assembly) ·
Injector driver assembly (P0620 set simultaneously) ·
Low quality fuel ·
Vehicle modifications ·
Fuel filter air bleed problem ·
Accessory problem (A/C, generator, etc.) ·
ECM |
Rough idling and excessive engine vibrations are checked in this troubleshooting procedure.
Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List result values may occur depending on the measuring conditions or the vehicle's age. Do not judge the vehicle to be normal even when the Data List values indicate a standard level. There are possibly some concealed factors of the malfunction.
Check that the vehicle has not been modified in any way prior to the vehicle inspection.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
After replacing the injection or supply pump assembly, the ECM needs initialization (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
After replacing the injector assembly, the ECM needs registration (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).
Before troubleshooting, conduct the following:
Check the fuel quality.
Check the fuel for air.
Check the fuel system for blockages.
Check the air filter.
Check the engine oil.
Check the engine coolant.
Check the engine idling speed and the maximum engine speed.
Check the vacuum pump.
Check the harness and connector connections of the common rail system components.
Check the following components and systems:
Sensors
Injection or supply pump assembly
Common rail assembly
Injector assemblies
Injector driver assembly
Turbocharger system
Intake and exhaust system
The wire harnesses and connectors are connected securely.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Drive the vehicle according to the driving pattern below to allow the ECM to set DTCs relating to malfunctions of the fuel system, EGR system and throttle valve. If DTCs are set, problem areas can be identified.
Enter Check Mode (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>CHECK MODE PROCEDURE).
Fully warm up the engine.
Allow the engine to idle for 5 minutes or more.
Drive the vehicle at more than 40 km/h (25 mph) for 1 minute or more (Procedure "A").
Decelerate and stop the vehicle (Procedure "B").
Repeat steps "A" (See procedure "A") and "B" (See procedure "B") 4 times or more.
Stop the engine and wait for at least 10 seconds (Procedure "C").
Repeat steps "A" (See procedure "A") and "C" (See procedure "C") described above (to set DTCs relating to the EGR system and throttle valve).
Drive the vehicle at more than 70 km/h (43 mph) for at least 1 minute (to set DTCs relating to the injection or supply pump assembly).
| Proceed to |
|---|
| NEXT |
NEXT
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| No DTCs | A |
| Engine related DTCs | B |
A
B
By performing this Active Test, the engine speed is maintained at 2000 rpm and the common rail internal fuel pressure is raised to the maximum operating pressure. As a result, a fuel leak check can be conducted while retaining the high common rail pressure.
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.
Visually check the injection or supply pump assembly, injector assembly, and fuel line located between the injection or supply pump assembly and common rail assembly for fuel leaks and fuel pressure leaks. Also, perform the same check on the fuel line between the common rail assembly and the injector assembly.
Visually check the injection or supply pump assembly, injector assembly, and fuel line located between the injection or supply pump assembly and common rail assembly for fuel leaks and fuel pressure leaks. Also, perform the same check on the fuel line between the common rail assembly and the injector assembly.
No fuel leak.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Start the engine and warm it up.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Enter the following menus in order and read the values.
MAF
Fuel Press
| Item | Engine Speed * | Standard Range | Description |
|---|---|---|---|
| MAF | Idling | 4 to 15 gm/s | Intake air volume detected by mass air flow meter sub-assembly |
| 3000 rpm (no engine load) | 80 to 90 gm/s | ||
| Fuel Press | Idling | 20000 to 30000 kPa | Common rail assembly internal fuel pressure |
*: The A/C switch and all accessory switches should be off, and the engine should be fully warmed up.
| Item | Result | Proceed to |
|---|---|---|
| MAF and Fuel press | Standard range | A |
| Only MAF | Outside standard range | B |
| Only Fuel Press | Outside standard range | C |
A
B
C
Enter the following menus in order and read the values.
Injection Feedback Val #1, #2, #3, and #4
Injection Volume
| Item | Engine Speed* | Standard Range | Description |
|---|---|---|---|
| Injection Feedback Val #1 | Idling | -7.0 to 7.0 mm3/st | Value of injector fuel injection volume compensates for differences in combustion condition of cylinders
·
Positive values indicate control which corrects combustion degradation ·
Negative values indicate control which corrects excessive combustion pressure ·
If problems exist, "Injection Feedback Val" may deviate from the -7.0 and 7.0 mm3/st range |
| Injection Feedback Val #2 | Idling | -7.0 to 7.0 mm3/st | |
| Injection Feedback Val #3 | Idling | -7.0 to 7.0 mm3/st | |
| Injection Feedback Val #4 | Idling | -7.0 to 7.0 mm3/st | |
| Injection Volume | Idling | 5.0 to 12.0 mm3/st | Fuel injection volume value controlled by ECU
·
Controls NE signal, fuel temperature, engine coolant temperature, intake air temperature, atmospheric pressure, and EGR volume. ·
If problems exist, "Injection Volume" may be outside the standard range |
| Result | Proceed to |
|---|---|
| Standard range | A |
| Injection Feedback Val #1 to #4 and/or Injection Volume outside standard range | B |
*: The A/C switch and all accessory switches should be off, and the engine should be fully warmed up.
A
B
Read the injector compensation code (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>PRECAUTION).
If the injector compensation code is not correctly registered, it may cause malfunctions (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).
Check the injector compensation code.
Compensation code of the installed injector assembly is same as the code registered in the ECM.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) battery terminal for at least 2 minutes.
Reconnect the cable to the negative (-) battery terminal.
Check whether the malfunction has been successfully repaired by performing a driving test.
Malfunction has been repaired successfully.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Visually check that the engine mounting insulator is installed correctly and is not crooked or twisted.
No abnormalities.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for air leaks and blockage between the air cleaner and turbocharger sub-assembly.
Check for air leaks and blockage between the turbocharger sub-assembly and intake manifold.
No air leaks or blockage.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the exhaust retarder assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the EGR valve assembly (Click here Engine / Hybrid System>N04C-VJ (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the diesel throttle body assembly (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>DIESEL THROTTLE BODY>ON-VEHICLE INSPECTION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Follow the instructions in the table below according to the check result of the GTS.
This operation is based on the premise that the common rail pressure is normal.
| Item | Engine Speed*1 | Reference Value |
|---|---|---|
| Injection Feedback Val #1 to #4 | Idling | -7.0 to 7.0 mm3/st |
| Injection Volume | Idling | 5.0 to 12.0 mm3/st |
*1: The A/C switch and all accessory switches should be off, and the engine should be fully warmed up.
| Injection Feedback Val #1 to #4 | Injection volume | ||
|---|---|---|---|
| Less than 5.0 mm3/st | Between 5.0 and 19.0 mm3/st (Normal) | More than 19.0 mm3/st | |
| 7.0 mm3/st or more, -7.0 mm3/st or less | A | B | B |
| Between -7.0 and 7.0 mm3/st | - | Normal | C*2 |
| Proceed to | Inspection Areas | Descriptions |
|---|---|---|
| A | Inspect and repair cylinder injector with revised injection volume of less than -7.0 mm3/st:
·
Perform power balance inspection and identify malfunctioning cylinder ·
Replace malfunctioning cylinder injector |
Abnormal value cylinder injector injects excessively large quantity of fuel |
| B | Identify malfunctioning cylinders by conducting power balance inspection:
·
Perform power balance inspection to identify malfunctioning cylinders ·
Clean malfunctioning cylinder injector, then check and repair it |
Abnormal value cylinder injector injects excessively large quantity of fuel
·
Fuel injection volume too low due to injector nozzle being blocked by deposits ·
Abnormal value cylinder injector compression decreases ·
Abnormal value cylinder injector injects excessively large quantity of fuel |
| C | Inspect and repair all cylinder injectors:
Clean all cylinder injectors, inspect, and repair them |
All cylinder injectors inject excessively small quantity of fuel:
Fuel injection volume too low due to all cylinder injector nozzles being blocked by deposits |
*2: When the Injection Volume displayed on the GTS is large despite the Fuel Press and Injection Feedback Val #1 to #4 in the Data List being normal, the injector assembly may be clogged. In this case, there may be deposits inside or outside the tip of the injector assembly.
Despite the injector assembly functioning normally, the indicated Injection Feedback Val #1 to #4 value may be outside the normal operating range due to compensation for other problems (such as low compression).
Injection Feedback Val #1 to #4 is the value used to correct the fuel injection volumes of each cylinder, in order to optimize (compensate for the unevenness between) all the cylinder combustion conditions. If any of the cylinders malfunction, the fuel injection volumes for the normal cylinders are corrected simultaneously. As a result, the Injection Feedback Val #1 to #4 may deviate from the standard range.
A
B
C
Use this Active Test to determine the malfunctioning cylinder.
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1 to #4 Fuel Cut.
If the engine idle speed does not change when a fuel injector assembly is disabled, the cylinder being tested is malfunctioning.
If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.
| Proceed to |
|---|
| NEXT |
NEXT
Use this Active Test to determine the malfunctioning cylinder.
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1 to #4 Fuel Cut.
If the engine idle speed does not change when a fuel injector assembly is disabled, the cylinder being tested is malfunctioning.
If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.
| Proceed to |
|---|
| NEXT |
NEXT
Check the cylinder compression pressure (Click here Engine / Hybrid System>N04C-VJ (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
If an injector assembly is contaminated with deposits, the fuel injection volume deviates from the standard range. This may cause malfunctions.
Check the injector assembly for any deposits.
| Result | Proceed to |
|---|---|
| Deposits | A |
| No deposits | B |
A
B
Wipe away deposits from the tips of the injectors.
Solvent or carbon removal agents help remove deposits easily.
Exercise extreme care not to damage the injector assemblies while wiping off the deposits.
| Proceed to |
|---|
| NEXT |
NEXT
Reinstall the injector assembly to the cylinder head.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Enter the following menus in order and read the values.
Injection Feedback Val #1, #2, #3, and #4
Injection Volume
| Item | Engine Speed* | Reference Value |
|---|---|---|
| Injection Feedback Val #1 to #4 | Idling | -7.0 to 7.0 mm3/st |
| Injection Volume | Idling | 5.0 to 12.0 mm3/st |
*: The A/C switch and all accessory switches should be off, and the engine should be fully warmed up. When the values are outside the standard range, deposits inside the injector assembly may be causing the problem.
Values are within the standard range.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
If an injector assembly is contaminated with deposits, the fuel injection volume deviates from the standard range. This may cause malfunctions.
Check the injector assembly for any deposits.
| Result | Proceed to |
|---|---|
| Deposits | A |
| No deposits | B |
A
B
Wipe away deposits from the tips of the injector assembly.
Solvent or carbon removal agents help remove deposits easily.
Exercise extreme care not to damage the injector assemblies while wiping off the deposits.
| Proceed to |
|---|
| NEXT |
NEXT
Reinstall the injector assembly to the cylinder head.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Enter the following menus in order and read the values.
Injection Feedback Val #1, #2, #3, and #4
Injection Volume
| Item | Engine Speed* | Reference Value |
|---|---|---|
| Injection Feedback Val #1 to #4 | Idling | -7.0 to 7.0 mm3/st |
| Injection Volume | Idling | 5.0 to 12.0 mm3/st |
*: The A/C switch and all accessory switches should be off, and the engine should be fully warmed up. When the values are outside the standard range, deposits inside the injector assembly may be causing the problem.
Values are within the standard range.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the common rail assembly (fuel pressure sensor).
Click hereEngine / Hybrid System>N04C-VJ (FUEL)>COMMON RAIL>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the injection or supply pump assembly (suction control valve).
Click hereEngine / Hybrid System>N04C-VJ (FUEL)>FUEL SUPPLY PUMP>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG