Home › Engine / Hybrid System › N04C-VJ (ENGINE CONTROL) › ECD SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _096807 N04C-VJ ENGINE CONTROL _0454116 ECD SYSTEM C

N04C-VJ ENGINE CONTROL  ECD SYSTEM  P1426  Differential Pressure Sensor Installation Error  P1427  Differential Pressure Sensor Circuit Low  P1428  Differential Pressure Sensor Circuit High  


DESCRIPTION

A190734E04
1.052,0.156 0.99,0.156 0.99,0.156 0.792,0.74 true 3.083,0.667 3,0.667 3,0.667 2.854,1.24 true 2.615,2.104 2.531,2.104 2.531,2.104 2.427,1.458 true 1.115,0.083 3.844,0.281 2.729,0.198 10 false Differential Pressure Sensor Assembly 3.146,0.604 4.49,0.792 1.344,0.188 10 false Metal Diaphragm 4.135,0.208 5.542,0.438 1.406,0.229 10 false Output Voltage (V) 4.885,2.323 7.052,2.583 2.167,0.26 10 false Pressure Characteristics (kPa) 5,2.125 5.208,2.292 0.208,0.167 10 false -5 5.198,2.125 5.333,2.292 0.135,0.167 10 false 0 6.26,2.115 6.552,2.281 0.292,0.167 10 false 100 4.458,1.781 4.875,1.948 0.417,0.167 10 false 0.555 4.531,1.646 4.917,1.813 0.385,0.167 10 false 0.75 4.531,0.917 4.917,1.083 0.385,0.167 10 false 4.65 1,2.146 2.792,2.5 1.792,0.354 10 false Atmospheric Pressure 0.063,2.448 3.167,2.792 3.104,0.344 10 false Pre-stage Oxidation Catalyst Fore Pressure 2.677,2.042 4.021,2.229 1.344,0.188 10 false Metal Diaphragm

The differential pressure sensor (differential pressure sensor assembly) is installed to the exhaust pipe and uses the built-in sensor to detect the pressure difference between the atmospheric pressure and the pre-stage oxidation catalyst fore pressure as voltage.

It is used to judge whether the filter inside the DPR is clogged.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1426 Differential Pressure Sensor Installation Error It is detected that the differential pressure before and after is a negative pressure (-3.5 kPa or less)
(1 trip detection logic)
·

Harness or connector

·

Differential pressure sensor assembly

·

ECM


Comes on DTC stored
P1427 Differential Pressure Sensor Circuit Low Short in differential pressure sensor assembly circuit
(1 trip detection logic)
·

Harness or connector

·

Differential pressure sensor assembly

·

ECM


Comes on DTC stored
P1428 Differential Pressure Sensor Circuit High Open in differential pressure sensor assembly circuit
(1 trip detection logic)
·

Harness or connector

·

Differential pressure sensor assembly

·

ECM


Comes on DTC stored

HINT:
·

If P1426 is output, the differential pressure sensor hose may not be piped correctly.

·

After checking that P1426, P1427, or P1428 is output, read the [DPF Differential Pressure] on the Data List screen using the GTS.

Differential Pressure Output Sensor Condition
-5 kPa or less
·

Short in PEX circuit to ground circuit

·

Open in VC circuit


100 kPa
·

Short in VC circuit and PEX circuit

·

Open in PEX circuit

·

Open in E2 circuit





CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P1426 After warm-up, fully depress the accelerator for 10 seconds or more.
P1427 Ignition switch ON for 30 seconds or more.
P1428

WIRING DIAGRAM

A261589E02
0.51,2.646 0.802,2.813 0.292,0.167 10 false A43 0.49,2.833 3.125,3.188 2.635,0.354 10 false Differential Pressure Sensor Assembly 5.896,2.667 6.604,3.01 0.708,0.344 10 false ECM 5,2.188 5.448,2.438 0.448,0.25 10 false B104 5,1.427 5.365,1.604 0.365,0.177 10 false B104 5,0.656 5.417,0.865 0.417,0.208 10 false B104 5.427,2.188 5.76,2.396 0.333,0.208 10 false E2 5.427,1.427 5.781,1.635 0.354,0.208 10 false PEX 5.427,0.646 5.938,0.885 0.51,0.24 10 false VC 1.906,2.208 2.271,2.385 0.365,0.177 10 false E2 1.813,1.427 2.177,1.583 0.365,0.156 10 false PEX 1.896,0.656 2.198,0.823 0.302,0.167 10 false VC 2.219,0.542 2.438,0.729 0.219,0.188 10 false 3 2.219,1.302 2.479,1.49 0.26,0.188 10 false 2 2.219,2.094 2.448,2.302 0.229,0.208 10 false 1 5.063,0.458 5.271,0.604 0.208,0.146 10 false 13 5.063,2.01 5.365,2.177 0.302,0.167 10 false 14 5.104,1.25 5.385,1.448 0.281,0.198 10 false 7

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / DPF Differential Pressure


d.

Read the value.

Result:
Condition Differential Pressure Proceed to
Always 100 kPa A
-5 kPa or less
-1 to 1 kPa B




A

2.CHECK HARNESS AND CONNECTOR (DIFFERENTIAL PRESSURE SENSOR ASSEMBLY - ECM)

B

CHECK CONNECTION OF VACUUM HOSE

2.CHECK HARNESS AND CONNECTOR (DIFFERENTIAL PRESSURE SENSOR ASSEMBLY - ECM)
a.

Disconnect the differential pressure sensor assembly connector.


b.

Disconnect the ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
B104-13 (VC) - A43-3 (VC) Always Below 1 Ω
B104-7 (PEX) - A43-2 (PEX) Always Below 1 Ω
B59-28 (E2) - A43-1 (E2) Always Below 1 Ω
B104-7 (PEX) or A43-2 (PEX) - Body ground Always 10 kΩ or higher
B104-13 (VC) or A43-3 (VC) - Bodyground Always 10 kΩ or higher


d.

Reconnect the differential pressure sensor assembly connector.


e.

Reconnect the ECM connectors.

Result:
Proceed to
OK
NG




OK

3.INSPECT ECM (VC VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ECM (VC VOLTAGE)
a.
A360756C05
1.542,0.25 1.938,0.448 0.396,0.198 1.76,1.583 2.177,0.885 true 2.552,1.615 2.24,0.875 true 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 1.594,0.281 1.969,0.438 0.375,0.156 10 false B104 1.542,1.667 2.073,1.865 0.531,0.198 10 false 14(E2) 2.385,1.677 2.958,1.885 0.573,0.208 10 false 13(VC)
*a Component with harness connected
(ECM)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.


Standard Voltage:
Tester Connection Switch Condition Specified Condition
B104-13 (VC) - B104-14 (E2) Ignition switch ON 4.5 to 5.5 V


Result:
Proceed to
OK
NG



OK

REPLACE DIFFERENTIAL PRESSURE SENSOR ASSEMBLY

NG