Home › Engine / Hybrid System › N04C-VJ (ENGINE CONTROL) › ECD SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _096807 N04C-VJ ENGINE CONTROL _0454116 ECD SYSTEM C

N04C-VJ ENGINE CONTROL  ECD SYSTEM  P20CD  Exhaust Aftertreatment Fuel Injector "A" Control Circuit Low  P20CE  Exhaust Aftertreatment Fuel Injector "A" Control Circuit High  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P20CD Exhaust Aftertreatment Fuel Injector "A" Control Circuit Low Diagnosis Condition:
·

Ignition switch ON


Malfunction Status:

FIV signal output is low when the exhaust fuel addition injector assembly is OFF


Malfunction Duration:

0.16 seconds or more


(1 trip detection logic)
·

Exhaust fuel addition injector assembly signal line

·

ECM


Comes on DTC stored
P20CE Exhaust Aftertreatment Fuel Injector "A" Control Circuit High Diagnosis Condition:
·

Ignition switch ON


Malfunction Status:

FIV signal output is high when the exhaust fuel addition injector assembly is OFF


Malfunction Duration:

7 times or more


(1 trip detection logic)
·

Exhaust fuel addition injector assembly signal line

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P20CD Ignition switch ON for 3 seconds or more.
P20CE Drive the vehicle for 20 minutes or more and check that the value of the exhaust temperature sensor is 250°C or higher.

WIRING DIAGRAM

A401616E03
0.604,2.75 1.427,2.958 0.823,0.208 10 false R/B NO.2-B 1.646,2.75 2.01,2.948 0.365,0.198 10 false P/I 0.417,3.406 1.031,3.635 0.615,0.229 10 false FL MAIN 0.552,4.083 1.104,4.281 0.552,0.198 10 false Battery 3.125,3.594 5,3.802 1.875,0.208 10 false No. 2 Integration Relay 2.896,2.75 3.573,2.938 0.677,0.188 10 false EFI-MAIN 4.031,3.281 4.344,3.458 0.313,0.177 10 false EFI 2.51,2.406 2.708,2.583 0.198,0.177 10 false 1 2.479,2.604 2.792,2.781 0.313,0.177 10 false 2E 2.521,2.844 2.75,3.031 0.229,0.188 10 false 3 2.479,3.021 2.792,3.198 0.313,0.177 10 false 2D 4.823,2.417 5.135,2.594 0.313,0.177 10 false 4 4.802,2.604 5.115,2.781 0.313,0.177 10 false 2D 4.833,2.844 5.146,3.021 0.313,0.177 10 false 2 4.802,3.031 5.115,3.208 0.313,0.177 10 false 2D 5.26,2.75 5.865,2.948 0.604,0.198 10 false EFI NO.2 6.156,2.406 6.469,2.583 0.313,0.177 10 false 24 6.125,2.604 6.438,2.781 0.313,0.177 10 false A57 6.156,2.833 6.469,3.01 0.313,0.177 10 false 25 6.115,3.021 6.479,3.208 0.365,0.188 10 false A56 6.531,3.427 7.01,3.646 0.479,0.219 10 false ECM 6.51,3.021 6.927,3.24 0.417,0.219 10 false MREL 6.51,2.604 6.823,2.781 0.313,0.177 10 false +B 6.51,0.677 6.823,0.854 0.313,0.177 10 false FIV 6.094,0.677 6.5,0.875 0.406,0.198 10 false B102 6.156,0.469 6.469,0.646 0.313,0.177 10 false 15 5.229,0.542 5.542,0.719 0.313,0.177 10 false 2 4.115,0.542 4.427,0.719 0.313,0.177 10 false 1 3.552,1.052 3.865,1.229 0.313,0.177 10 false j6 3.531,1.24 6.188,1.729 2.656,0.49 10 false Exhaust Fuel Addition Injector Assembly

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read the DTCs.

Result:
Result Proceed to
DTC P20CD and P20CE are output A
P20CD and/or P20CE and other DTCs are output B




A

2.CHECK EXHAUST FUEL ADDITION INJECTOR ASSEMBLY

B

2.CHECK EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
A165237C05
0.344,0.906 0.833,1.198 0.49,0.292 0.094,0.104 0.5,0.427 0.406,0.323 10 false *a 0.552,0.99 0.875,1.188 0.323,0.198 10 false j6
*a Front view of wire harness connector
(to Exhaust Fuel Addition Injector Assembly)


a.

Disconnect the exhaust fuel addition injector assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
j6-2 - Body ground Ignition switch ON 11 to 14 V
j6-1 - Body ground Ignition switch ON 0 to 2 V



Result:
Proceed to
OK
NG



OK

3.CHECK EXHAUST FUEL ADDITION INJECTOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

3.CHECK EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
a.

Check the installation of the exhaust fuel addition injector assembly.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (EXHAUST FUEL ADDITION INJECTOR ASSEMBLY - ECM)

NG

REPAIR OR REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (EXHAUST FUEL ADDITION INJECTOR ASSEMBLY - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the exhaust fuel addition injector assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
j1-2 - B102-15 (FIV) Always Below 1 Ω
j1-2 or B102-15 (FIV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ECM

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR