Home › Engine / Hybrid System › N04C-VJ (ENGINE CONTROL) › ECD SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _096807 N04C-VJ ENGINE CONTROL _0454116 ECD SYSTEM C

N04C-VJ ENGINE CONTROL  ECD SYSTEM  P0724  Brake Switch "B" Circuit High  


DESCRIPTION

This DTC indicates that the stop light switch remains on. When the stop light switch remains on during GO and STOP driving, the ECM interprets this as a fault in the stop light switch. Then the MIL illuminates and the ECM stores the DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0724 Brake Switch "B" Circuit High Stop light switch remains on even when vehicle is driven in GO (30 km/h (19 mph) or more) and STOP (less than 3 km/h (1.8 mph)) pattern 5 times (2 trip detection logic).
·

Short in stop light switch signal circuit

·

Stop light switch assembly

·

ECM


Comes on DTC stores

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Condition
P0724 Accelerate the vehicle to 30 km/h (19 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.8 mph) or less 5 times.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.


e.

Read the value displayed on the GTS when the brake pedal is depressed and released.

OK:
Brake Pedal GTS Display
Released OFF
Depressed ON



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Remove the stop light switch assembly.


b.
A161615C01
0.094,0.042 0.406,0.26 0.313,0.219 10 false *a 2.25,1.677 2.521,1.854 0.271,0.177 10 false *b
*a Component without harness connected
(Stop Light Switch Assembly)
*b Pushed


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Not pushed Below 1 Ω
Pushed 10 kΩ or higher
3 - 4 Not pushed 10 kΩ or higher
Pushed Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK ECM (STP VOLTAGE)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK ECM (STP VOLTAGE)
a.
A220581C20
0.292,2.594 0.698,2.823 0.406,0.229 0.667,3.219 0.896,3.854 true 0.354,2.615 0.667,2.823 0.313,0.208 10 false A57 0.656,3.906 1.323,4.104 0.667,0.198 10 false 8 (STP) 0.198,0.427 0.51,0.635 0.313,0.208 10 false *a 1.677,0.427 1.99,0.635 0.313,0.208 10 false *b 0.167,2.042 0.479,2.25 0.313,0.208 10 false *c
*a Brake Pedal Depressed
*b Brake Pedal Released
*c Component with harness connected
(ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Condition Specified Condition
A57-8 (STP) - Body ground Released 0 to 2 V
Depressed 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)