Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM › from 2021.01
RM2850E _57 Power Source / Network _073263 CAN COMMUNICATION _0356688 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  Open in Bus 2 Main Bus Line  


DESCRIPTION

There may be an open circuit in one of the bus 2 main lines when the resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.

Detection Item Trouble Area

*1: except N04C-WA and 1HZ

*2: for N04C-WA

Resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.
·

CAN main wire or connector

·

ECM*1

·

Translate ECU Assembly*2

·

Central gateway ECU (network gateway ECU)

·

No. 66 junction connector*1

·

No. 7 CAN junction connector*2



This malfunction is not related to the lines of a bus 2 branch except the central gateway ECU CAN branch wires or to ECUs or sensors connected a bus 2 branch.

WIRING DIAGRAM

except N04C-WA and 1HZ
C454779E01
0.854,0.365 1.469,0.563 0.615,0.198 10 false CA4H 0.885,1.104 1.5,1.302 0.615,0.198 10 false CA4L 0.167,1.427 0.781,1.625 0.615,0.198 10 false J51 0.146,1.604 1.646,1.99 1.5,0.385 10 false Central Gateway ECU (Network Gateway ECU) 2.563,1.375 3.177,1.573 0.615,0.198 10 false A85 2.563,1.531 4.292,1.771 1.729,0.24 10 false No. 66 Junction Connector 5.958,0.375 6.573,0.573 0.615,0.198 10 false CANH 5.969,1.083 6.583,1.281 0.615,0.198 10 false CANL 1.75,2.385 4.25,2.573 2.5,0.188 10 false *1: for N04C-VQ, N04C-VL, N04C-VJ 4.458,2.385 5.698,2.594 1.24,0.208 10 false *2: for 2TR-FE 5.271,0.281 5.885,0.479 0.615,0.198 10 false 7*1 5.583,0.281 6.198,0.479 0.615,0.198 10 false 33*2 5.604,0.813 6.219,1.01 0.615,0.198 10 false 34*2 5.26,0.813 5.875,1.01 0.615,0.198 10 false 1*1 6.26,1.406 6.719,1.604 0.458,0.198 10 false ECM 5.25,0.469 5.708,0.667 0.458,0.198 10 false A56 5.625,0.469 6.083,0.667 0.458,0.198 10 false A53 5.625,1 6.083,1.198 0.458,0.198 10 false A53 5.25,1 5.708,1.198 0.458,0.198 10 false A56 1.323,0.375 1.635,0.573 0.313,0.198 10 false 18 1.333,0.906 1.646,1.104 0.313,0.198 10 false 17 3.24,0.375 3.552,0.573 0.313,0.198 10 false 3 3.177,0.917 3.49,1.115 0.313,0.198 10 false 14 3.833,0.385 4.146,0.583 0.313,0.198 10 false 1 3.823,0.917 4.135,1.115 0.313,0.198 10 false 12

for N04C-WA
C422184E01
1.323,1.385 1.635,1.583 0.313,0.198 10 false 18 1.323,1.917 1.635,2.115 0.313,0.198 10 false 17 2.885,1.365 3.198,1.563 0.313,0.198 10 false 5 2.833,1.927 3.146,2.125 0.313,0.198 10 false 16 4.146,1.365 4.458,1.563 0.313,0.198 10 false 6 4.156,1.917 4.469,2.115 0.313,0.198 10 false 17 5.729,1.385 6.042,1.583 0.313,0.198 10 false 31 5.719,1.917 6.031,2.115 0.313,0.198 10 false 32 0.854,1.396 1.469,1.594 0.615,0.198 10 false CA4H 0.875,2.104 1.49,2.302 0.615,0.198 10 false CA4L 5.969,1.385 6.583,1.583 0.615,0.198 10 false CAN+ 5.969,2.125 6.583,2.323 0.615,0.198 10 false CAN- 0.073,2.385 0.531,2.583 0.458,0.198 10 false J51 2.635,2.302 3.094,2.5 0.458,0.198 10 false A123 5.438,2.292 5.896,2.49 0.458,0.198 10 false V9 0.073,2.563 2.063,2.948 1.99,0.385 10 false Central Gateway ECU (Network Gateway ECU) 2.646,2.479 4.552,2.677 1.906,0.198 10 false No. 7 CAN Junction Connector 5.448,2.458 7.052,2.76 1.604,0.302 10 false Translate ECU Assembly

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
except N04C-WA and 1HZ A
for N04C-WA B



A

2.CHECK FOR OPEN IN CAN BUS WIRE (NO. 66 JUNCTION CONNECTOR)

B

5.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR)
2.CHECK FOR OPEN IN CAN BUS WIRE (NO. 66 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 66 junction connector.


c.
C358905E08
1.531,0.146 1.885,0.396 0.354,0.25 1.292,1.063 1.292,0.26 1.292,0.26 1.125,0.26 true 1.302,1.344 1.302,1.99 1.302,1.99 1.156,1.99 true 0.99,1.073 0.792,0.531 0.792,0.531 0.646,0.531 true 1.01,1.333 0.896,1.708 0.896,1.708 0.74,1.708 true 0.552,0.177 1.469,0.375 0.917,0.198 10 false CANH*c 0.073,0.458 0.99,0.656 0.917,0.198 10 false CANH*b 0.177,1.625 1.094,1.823 0.917,0.198 10 false CANL*b 0.604,1.896 1.521,2.094 0.917,0.198 10 false CANL*c 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 1.583,0.177 1.896,0.375 0.313,0.198 10 false A85

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
A85-1 (CANH) - A85-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω ECM
A85-3 (CANH) - A85-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)


Text in Illustration
*a Front view of wire harness connector
(to No. 66 Junction Connector)
*b to ECM
*c to Central Gateway ECU (Network Gateway ECU)


Result:
Result Proceed to
OK A
NG (Central gateway ECU CAN main wire) B
NG (ECM CAN main wire) C



A

REPLACE NO. 66 JUNCTION CONNECTOR

B

3.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU - NO. 66 JUNCTION CONNECTOR)

C

4.CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 66 JUNCTION CONNECTOR)
3.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU - NO. 66 JUNCTION CONNECTOR)
a.

Reconnect the A85 No. 66 junction connector.


b.

Disconnect the central gateway ECU (network gateway ECU) connector.


c.
C326490E90
1.5,0.104 1.854,0.385 0.354,0.281 1.99,1.896 1.854,1.896 1.854,1.896 1.646,1.198 true 2.313,1.75 2.177,1.75 2.177,1.75 1.802,1.219 true 2.052,1.813 2.667,2.01 0.615,0.198 10 false CA4L 2.365,1.667 2.979,1.865 0.615,0.198 10 false CA4H 1.573,0.156 2.188,0.354 0.615,0.198 10 false J51 0.073,0.052 0.688,0.25 0.615,0.198 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J51-18 (CA4H) - J51-17 (CA4L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])


Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU - NO. 66 JUNCTION CONNECTOR)

4.CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 66 JUNCTION CONNECTOR)
a.

Reconnect the A85 No. 66 junction connector.


b.
C371321N02
1.5,0.104 1.875,0.323 0.375,0.219 1.51,2.563 1.896,2.813 0.385,0.25 0.896,0.927 1.063,0.927 1.063,0.927 1.26,1.063 true 0.917,1.365 1.052,1.365 1.052,1.365 1.26,1.26 true 1.885,4.313 2.052,4.313 2.052,4.313 2.052,3.813 true 2.323,4.313 2.167,4.313 2.167,4.313 2.167,3.813 true 0.479,1.292 1.094,1.49 0.615,0.198 10 false CANH 0.479,0.854 1.094,1.052 0.615,0.198 10 false CANL 0.104,0.063 0.719,0.26 0.615,0.198 10 false *a 1.563,0.135 2.177,0.333 0.615,0.198 10 false A56 1.583,2.594 2.198,2.792 0.615,0.198 10 false A53 1.938,0.125 2.552,0.323 0.615,0.198 10 false *A 1.948,2.594 2.563,2.792 0.615,0.198 10 false *B 1.448,4.24 2.063,4.438 0.615,0.198 10 false CANH 2.406,4.24 3.021,4.438 0.615,0.198 10 false CANL

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for N04C-VQ, N04C-VL, N04C-VJ
Tester Connection Condition Specified Condition
A56-7 (CANH) - A56-1 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

for 2TR-FE
Tester Connection Condition Specified Condition
A53-33 (CANH) - A53-34 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*A for N04C-VQ, N04C-VL, N04C-VJ
*B for 2TR-FE
*a Front view of wire harness connector
(to ECM)


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (ECM - NO. 66 JUNCTION CONNECTOR)

5.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 7 CAN junction connector.

C405889N02
3.25,0.167 3.667,0.417 0.417,0.25 2.823,0.417 2.99,0.417 2.99,0.417 3.438,1.417 true 2.667,0.583 2.833,0.583 2.833,0.583 3.26,1.406 true 2.833,2.5 3,2.5 3,2.5 3.458,1.688 true 2.667,2.333 2.833,2.333 2.833,2.333 3.313,1.667 true 3.323,0.229 4.24,0.427 0.917,0.198 10 false A123 0.115,0.115 1.031,0.313 0.917,0.198 10 false *a 2.094,0.49 3.01,0.688 0.917,0.198 10 false CANH*b 2.26,0.323 3.177,0.521 0.917,0.198 10 false CANH*c 2.156,2.271 3.073,2.469 0.917,0.198 10 false CANL*b 2.323,2.448 3.24,2.646 0.917,0.198 10 false CANL*c

Text in Illustration
*a Front view of wire harness connector
(to No. 7 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to Translate ECU Assembly - -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
A123-5 (CANH) - A123-16 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
A123-6 (CANH) - A123-17 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Translate ECU assembly



d.

Reconnect the No. 7 CAN junction connector.


Result:
Result Proceed to
OK A
NG (Central gateway ECU CAN main wire) B
NG (Translate ECU assembly CAN main wire) C



A

REPLACE NO. 7 CAN JUNCTION CONNECTOR

B

6.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU - NO. 7 CAN JUNCTION CONNECTOR)

C

7.CHECK FOR OPEN IN CAN BUS WIRE (TRANSLATE ECU ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)
6.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU - NO. 7 CAN JUNCTION CONNECTOR)
a.

Disconnect the central gateway ECU (network gateway ECU) connector.


b.
C326490E90
1.5,0.104 1.854,0.385 0.354,0.281 1.99,1.896 1.854,1.896 1.854,1.896 1.646,1.198 true 2.313,1.75 2.177,1.75 2.177,1.75 1.802,1.219 true 2.052,1.813 2.667,2.01 0.615,0.198 10 false CA4L 2.365,1.667 2.979,1.865 0.615,0.198 10 false CA4H 1.573,0.156 2.188,0.354 0.615,0.198 10 false J51 0.073,0.052 0.688,0.25 0.615,0.198 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J51-18 (CA4H) - J51-17 (CA4L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])


Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU - NO. 7 CAN JUNCTION CONNECTOR)

7.CHECK FOR OPEN IN CAN BUS WIRE (TRANSLATE ECU ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)
a.

Disconnect the translate ECU assembly connector.


b.
C407760N04
1.417,0.375 1.771,0.625 0.354,0.25 2.333,2.75 2.167,2.75 2.167,2.75 2.063,2.219 true 2.281,3.031 2.115,3.031 2.115,3.031 1.927,2.25 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.5,0.427 2.333,0.625 0.833,0.198 10 false V9 2.385,2.677 3.219,2.875 0.833,0.198 10 false CAN- 2.333,2.969 3.167,3.167 0.833,0.198 10 false CAN+

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V9-31 (CAN+) - V9-32 (CAN-) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Translate ECU Assembly)


Result:
Proceed to
OK
NG



OK

REPLACE TRANSLATE ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (TRANSLATE ECU ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)