Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2021.01
RM2850E _58 Vehicle Interior _073141 METER / GAUGE / DISPLAY _0357098 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Fuel Receiver Gauge Malfunction  


DESCRIPTION

The combination meter assembly controls the fuel receiver gauge in accordance with the resistance of the fuel sender gauge, which varies depending on the amount of fuel remaining in the fuel tank.

WIRING DIAGRAM

E462187E01
5.167,0.896 5.625,1.094 0.458,0.198 10 false FV 2.635,1.781 3.094,1.979 0.458,0.198 10 false FR2 2.656,2.313 3.115,2.51 0.458,0.198 10 false FE2 3.031,0.76 3.49,0.958 0.458,0.198 10 false 3 3.042,1.781 3.5,1.979 0.458,0.198 10 false 1 3.052,2.313 3.51,2.51 0.458,0.198 10 false 2 4.865,0.771 5.323,0.969 0.458,0.198 10 false 35 4.854,1.792 5.313,1.99 0.458,0.198 10 false 33 4.854,2.323 5.313,2.521 0.458,0.198 10 false 34 2.656,0.771 3.115,0.969 0.458,0.198 10 false FV2 5.167,1.896 5.625,2.094 0.458,0.198 10 false FR 5.167,2.427 5.625,2.625 0.458,0.198 10 false FE 1.229,2.99 1.688,3.188 0.458,0.198 10 false g1 4.844,2.979 5.302,3.177 0.458,0.198 10 false J1 1.229,3.219 3.156,3.448 1.927,0.229 10 false Fuel Sender Gauge Assembly 4.833,3.198 6.76,3.427 1.927,0.229 10 false Combination Meter Assembly

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (FUEL METER OPERATION)
a.

Using the GTS, perform the Active Test (Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter:
Tester Display Test Part Control Range Diagnostic Note
Fuel Meter Operation Fuel receiver gauge assembly OFF, Sender E, Empty, Warning, 1/4, 1/2, 3/4, Full or Sender F -

OK:

Fuel receiver gauge assembly indication is normal according to the GTS operation.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (FUEL INPUT)

NG

REPLACE COMBINATION METER ASSEMBLY

2.READ VALUE USING GTS (FUEL INPUT)
a.

Using the GTS, read the Data List (Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter:
Tester Display Measurement Item / Range Normal Condition Diagnostic Note
Fuel Input Fuel input / Min.: 0, Max.: 127.5 Current fuel level displayed Unit: Liter

OK:

Fuel level data displayed on the GTS is almost the same as the fuel receiver gauge assembly indication.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

3.INSPECT FUEL SENDER GAUGE ASSEMBLY
3.INSPECT FUEL SENDER GAUGE ASSEMBLY
a.

Remove the fuel sender gauge assembly.


b.

Inspect the fuel sender gauge assembly.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SENDER GAUGE ASSEMBLY AND BODY GROUND)

NG

REPLACE FUEL SENDER GAUGE ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SENDER GAUGE ASSEMBLY AND BODY GROUND)
a.

Disconnect the J1 combination meter assembly connector.


b.

Disconnect the g1 fuel sender gauge assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-35 (FV) - g1-3 (FV2) Always Below 1 Ω
J1-34 (FE) - g1-2 (FE2) Always Below 1 Ω
J1-33 (FR) - g1-1 (FR2) Always Below 1 Ω
J1-35 (FV) - Body ground Always 10 kΩ or higher
J1-34 (FE) - Body ground Always 10 kΩ or higher
J1-33 (FR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR