Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch) › from 2021.01
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356878 ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)  Brake Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

If any of the following is detected, the brake warning light remains on:

·

The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).

·

The brake fluid level is insufficient.

·

EBD operation is not possible.

·

The vacuum inside the brake booster decreases.


WIRING DIAGRAM

C376799E02
1.802,0.594 2.115,0.792 0.313,0.198 10 false SW 1.542,0.906 1.854,1.104 0.313,0.198 10 false 32 1.531,0.458 1.844,0.656 0.313,0.198 10 false 31 1.823,1.01 2.188,1.219 0.365,0.208 10 false BRL 2.698,0.573 3.219,0.771 0.521,0.198 10 false CANL 6.167,0.563 6.688,0.76 0.521,0.198 10 false CANL 2.677,0.979 3.198,1.177 0.521,0.198 10 false CANH 3.146,0.406 3.458,0.604 0.313,0.198 10 false 22 5.917,0.813 6.229,1.01 0.313,0.198 10 false 22 6.177,0.99 6.698,1.188 0.521,0.198 10 false CANH 3.146,0.823 3.458,1.021 0.313,0.198 10 false 23 5.906,0.396 6.219,0.594 0.313,0.198 10 false 10 5.917,4 6.229,4.198 0.313,0.198 10 false 25 6.177,1.917 6.583,2.135 0.406,0.219 10 false IG1 6.198,4.115 6.677,4.333 0.479,0.219 10 false GND1 5.927,1.781 6.24,1.979 0.313,0.198 10 false 12 1.396,1.24 1.708,1.438 0.313,0.198 10 false J1 1.396,1.427 3.448,1.625 2.052,0.198 10 false Combination Meter Assembly 3.375,1.906 4.458,2.104 1.083,0.198 10 false from IG Circuit 4.719,2.094 5.802,2.292 1.083,0.198 10 false ECU-IG1 NO. 3 2.208,2.781 2.521,2.979 0.313,0.198 10 false A6 3.417,2.781 3.729,2.979 0.313,0.198 10 false A7 2.229,2.552 2.542,2.75 0.313,0.198 10 false 1 3.438,2.563 3.75,2.76 0.313,0.198 10 false 1 2.156,3.167 3.74,3.531 1.583,0.365 10 false Vacuum Warning Switch Assembly* 1.031,1.917 1.344,2.115 0.313,0.198 10 false * 1.406,3.875 1.719,4.073 0.313,0.198 10 false 1 2.521,3.885 2.833,4.083 0.313,0.198 10 false 2 2.292,3.896 2.604,4.094 0.313,0.198 10 false E 1.594,3.896 1.906,4.094 0.313,0.198 10 false + 0.24,4.26 0.552,4.458 0.313,0.198 10 false F2 0.219,4.458 3.188,4.854 2.969,0.396 10 false Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly) 0.729,5.417 2.813,5.656 2.083,0.24 10 false : CAN Communication System 5.385,4.688 5.75,4.885 0.365,0.198 10 false A71 5.375,4.885 7.01,5.281 1.635,0.396 10 false Skid Control ECU (Brake Actuator Assembly) 3.51,5.271 4.76,5.49 1.25,0.219 10 false *: except 2TR-FE

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM

A

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

OK

3.INSPECT BATTERY

NG

CONNECT CONNECTOR TO BRAKE ACTUATOR ASSEMBLY CORRECTLY

3.INSPECT BATTERY

OK

4.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)

NG

CHECK OR REPLACE CHARGING SYSTEM OR BATTERY

4.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)

OK

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
C306843E30
1.469,0.115 1.875,0.344 0.406,0.229 0.896,1.854 0.708,1.24 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.542,0.146 1.958,0.323 0.417,0.177 10 false A71 0.729,1.896 1.229,2.073 0.5,0.177 10 false GND1

Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A71-25 (GND1) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Result:
Result Proceed to
OK (N04C-UH, N04C-VQ, N04C-VL, N04C-WA) A
OK (2TR-FE) B
NG C



A

6.INSPECT VACUUM WARNING SWITCH ASSEMBLY

B

8.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

6.INSPECT VACUUM WARNING SWITCH ASSEMBLY
a.

Start the engine.


b.

Idle the engine.


c.

Disconnect the A6 vacuum warning switch assembly connector and check the brake warning light.

Result:
Result Proceed to
Brake warning light does not turn off A
Brake warning light turns off B


HINT:

If the brake warning light turns off, the vacuum warning switch has an internal short circuit.




A

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - VACUUM WARNING SWITCH ASSEMBLY)

B

REPLACE VACUUM WARNING SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - VACUUM WARNING SWITCH ASSEMBLY)
a.

Turn the ignition switch off.


b.

Disconnect the A7 vacuum warning switch assembly connector.


c.

Disconnect the J1 combination meter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-32 (BRL) - A6-1 Always Below 1 Ω
J1-32 (BRL) or A6-1 - Body ground Always 10 kΩ or higher
A7-1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY
a.

Turn the ignition switch off.


b.

With the brake fluid at the specified level, disconnect the F2 brake fluid level warning switch (brake master cylinder reservoir assembly) connector and check the brake warning light.

Result:
Result Proceed to
Brake warning light does not turn off A
Brake warning light turns off B


HINT:

If the brake warning light turns off, the brake fluid level warning switch (brake master cylinder reservoir assembly) has an internal short circuit.




A

9.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY)

B

REPLACE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-31 (SW) - F2-1 (+) Always Below 1 Ω
J1-31 (SW) or F2-1 (+) - Body ground Always 10 kΩ or higher
F2-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.READ VALUE USING GTS (BRAKE WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.READ VALUE USING GTS (BRAKE WARNING LIGHT)
a.

Reinstall the reservoir filler cap and strainer.


b.

Reconnect the J1 combination meter assembly connector, A6 and A7 vacuum warning switch assembly connectors, F2 brake fluid level warning switch (brake master cylinder sub-assembly) connector and A71 skid control ECU (brake actuator assembly) connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


g.

According to the display on the GTS, read the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Brake Warning Light Brake warning light/ ON or OFF ON: Warning light on
OFF: Warning light off
-


h.

Check the GTS display condition of the brake warning light.


Result:
Result Proceed to
Display of the Data List remains OFF A
Display of the Data List remains ON B



A

B