Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch) › from 2021.01
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356878 ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)  C1241  Low Power Supply Voltage Malfunction  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits ABS operation.

This DTC is stored when the +BS terminal voltage deviates from the DTC detection condition due to a malfunction in the power supply or charging circuit such as the battery or generator circuit, etc.

The DTC is canceled when the +BS terminal voltage returns to normal.

DTC No. DTC Detection Condition Trouble Area
C1241 Either of the following is detected:
1.

When vehicle speed is 3 km/h (2 mph) or more, +BS terminal voltage is continuously below 9.5 V for 10 seconds or more.

2.

When solenoid relay is on, +BS terminal voltage is below 9.5 V and relay contact is off for 0.22 seconds or more.

3.

When +BS terminal voltage is below 9.5 V, power supply voltage of vehicle speed sensor is continuously low for 60 seconds or more.

4.

When fail-safe motor relay is on and +BS terminal voltage is below 9.5 V, fail-safe motor relay overcurrent continues for 0.05 seconds or more.


·

ABS NO. 2 fuse

·

Battery

·

Charging system

·

Wire harness or connector

·

Skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

C268657E11
1.083,1.042 2.052,1.26 0.969,0.219 10 false from Battery 3.417,1.24 4.385,1.458 0.969,0.219 10 false ABS NO. 2 5.781,1.042 6.26,1.26 0.479,0.219 10 false +BS 5.792,2.802 6.271,3.021 0.479,0.219 10 false GND1 5.5,0.958 5.802,1.177 0.302,0.219 10 false 38 5.5,2.677 5.802,2.896 0.302,0.219 10 false 25 5.5,3.833 5.927,4.042 0.427,0.208 10 false A71 5.479,4.021 7.083,4.417 1.604,0.396 10 false Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V


HINT:
Refer to the inspection procedures:
Engine Type See page
N04C-UH (Click here)
N04C-VQ (Click here)
N04C-VL (Click here)
N04C-WA (Click here)
2TR-FE (w/ Generator for 80 A Type) (Click here)
2TR-FE (w/ Generator for 100 A Type) (Click here)



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (+BS TERMINAL)

NG

CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY

2.CHECK TERMINAL VOLTAGE (+BS TERMINAL)
a.

Turn the ignition switch off.


b.
C306843E23
1.448,0.135 1.906,0.365 0.458,0.229 2.604,1.833 2.688,1.25 true 1.542,0.167 1.896,0.354 0.354,0.188 10 false A71 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 2.438,1.844 2.844,2.042 0.406,0.198 10 false +BS

Make sure that there is no looseness in the locking part and connecting part of the connectors.


c.

Disconnect the A71 skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A71-38 (+BS) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (+BS CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
C306843E24
1.49,0.135 1.917,0.354 0.427,0.219 0.896,1.833 0.698,1.26 true 0.125,0.115 0.438,0.313 0.313,0.198 10 false *a 1.573,0.167 1.938,0.365 0.365,0.198 10 false A71 0.74,1.875 1.24,2.073 0.5,0.198 10 false GND1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A71-25 (GND1) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

4.RECONFIRM DTC
a.

Reconnect the A71 skid control ECU (brake actuator assembly) connector.



c.

Turn the ignition switch off.


d.

Start the engine.


e.

Perform a road test.


f.

Check if the same DTC is recorded (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1241 is not output A
DTC C1241 is output B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>PROBLEM SYMPTOMS TABLE).




A

B