Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2021.01
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356689 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Brake Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

If any of the following is detected, the brake warning light remains on:

·

The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).

·

The brake fluid level is insufficient.

·

EBD operation is not possible.

·

The vacuum inside the brake booster decreases.


WIRING DIAGRAM

C376799E01
1.531,0.458 1.844,0.656 0.313,0.198 10 false 31 1.833,0.594 2.146,0.792 0.313,0.198 10 false SW 1.833,1.01 2.146,1.208 0.313,0.198 10 false BRL 1.531,0.875 1.844,1.073 0.313,0.198 10 false 32 2.656,0.594 3.135,0.813 0.479,0.219 10 false CANL 2.646,0.979 3.177,1.219 0.531,0.24 10 false CANH 3.167,0.365 3.479,0.563 0.313,0.198 10 false 22 3.177,0.802 3.49,1 0.313,0.198 10 false 23 5.865,0.375 6.177,0.573 0.313,0.198 10 false 10 5.865,0.792 6.177,0.99 0.313,0.198 10 false 22 6.208,0.573 6.708,0.771 0.5,0.198 10 false CANL 6.208,0.979 6.677,1.208 0.469,0.229 10 false CANH 6.198,1.917 6.51,2.115 0.313,0.198 10 false IG1 5.854,1.76 6.167,1.958 0.313,0.198 10 false 12 4.677,2.094 5.698,2.292 1.021,0.198 10 false ECU-IG1 NO. 3 3.292,1.917 4.25,2.177 0.958,0.26 10 false from IG Circuit 1.531,1.323 1.844,1.521 0.313,0.198 10 false J1 1.542,1.531 3.76,1.781 2.219,0.25 10 false Combination Meter Assembly 1.094,2.01 1.406,2.208 0.313,0.198 10 false * 2.229,2.573 2.469,2.771 0.24,0.198 10 false 1 2.198,2.781 2.51,2.979 0.313,0.198 10 false A6 3.448,2.573 3.677,2.771 0.229,0.198 10 false 1 3.417,2.781 3.729,2.979 0.313,0.198 10 false A7 2.167,3.198 3.719,3.552 1.552,0.354 10 false Vacuum Warning Switch Assembly* 1.406,3.885 1.719,4.083 0.313,0.198 10 false 1 1.594,3.875 1.906,4.073 0.313,0.198 10 false + 2.271,3.885 2.583,4.083 0.313,0.198 10 false E 2.479,3.885 2.792,4.083 0.313,0.198 10 false 2 0.167,4.365 0.479,4.563 0.313,0.198 10 false F2 0.167,4.542 3.156,4.927 2.99,0.385 10 false Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly) 0.698,5.417 2.729,5.656 2.031,0.24 10 false : CAN Communication System 3.333,5.438 4.583,5.698 1.25,0.26 10 false *: except 2TR-FE 5.5,4.729 5.813,4.927 0.313,0.198 10 false A71 5.5,4.927 7.042,5.344 1.542,0.417 10 false Skid Control ECU (Brake Actuator Assembly) 6.188,4.094 6.677,4.292 0.49,0.198 10 false GND1 5.865,3.969 6.177,4.167 0.313,0.198 10 false 25

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK CAN COMMUNICATION LINE
a.

Check if CAN communication system DTCs are output (Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).


Result:
Result Proceed to
DTC is not output A
DTC is output B



A

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.INSPECT BATTERY

NG

CONNECT CONNECTOR TO BRAKE ACTUATOR ASSEMBLY CORRECTLY

3.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V


HINT:
Refer to the inspection procedures:
Engine Type See page
N04C-VL (Click here)
N04C-VJ (Click here)
N04C-WA (Click here)



Result:
Proceed to
OK
NG



OK

4.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)

NG

CHECK OR REPLACE CHARGING SYSTEM OR BATTERY

4.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)
a.

Turn the ignition switch off.


b.
C399804E06
1.531,0.135 1.885,0.365 0.354,0.229 2.833,1.813 2.427,0.927 true 0.135,0.073 0.448,0.271 0.313,0.198 10 false *a 2.76,1.865 3.083,2.052 0.323,0.188 10 false IG1 1.594,0.167 1.979,0.406 0.385,0.24 10 false A71

Disconnect the A71 skid control ECU (brake actuator assembly) connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A71-12 (IG1) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
C399804E02
1.531,0.135 1.885,0.365 0.354,0.229 0.958,1.813 0.698,1.24 true 0.135,0.073 0.448,0.271 0.313,0.198 10 false *a 0.823,1.896 1.344,2.156 0.521,0.26 10 false GND1 1.594,0.167 1.979,0.406 0.385,0.24 10 false A71

Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A71-25 (GND1) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Result:
Proceed to
OK
NG



OK

6.INSPECT VACUUM WARNING SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

6.INSPECT VACUUM WARNING SWITCH ASSEMBLY
a.

Start the engine.


b.

Idle the engine.


c.

Disconnect the A6 vacuum warning switch assembly connector and check the brake warning light.

Result:
Result Proceed to
Brake warning light does not turn off A
Brake warning light turns off B


HINT:

If the brake warning light turns off, the vacuum warning switch has an internal short circuit.




A

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - VACUUM WARNING SWITCH ASSEMBLY)

B

REPLACE VACUUM WARNING SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - VACUUM WARNING SWITCH ASSEMBLY)
a.

Turn the ignition switch off.


b.

Disconnect the A7 vacuum warning switch assembly connector


c.

Disconnect the J1 combination meter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-32 (BRL) - A6-1 Always Below 1 Ω
J1-32 (BRL) or A6-1 - Body ground Always 10 kΩ or higher
A7-1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY
a.

Turn the ignition switch off.


b.

With the brake fluid at the specified level, disconnect the F2 brake fluid level warning switch (brake master cylinder reservoir assembly) connector and check the brake warning light.

Result:
Result Proceed to
Brake warning light does not turn off A
Brake warning light turns off B


HINT:

If the brake warning light turns off, the brake fluid level warning switch (brake master cylinder reservoir assembly) has an internal short circuit.




A

9.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY)

B

REPLACE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-31 (SW) - F2-1 (+) Always Below 1 Ω
J1-31 (SW) or F2-1 (+) - Body ground Always 10 kΩ or higher
F2-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.READ VALUE USING GTS (BRAKE WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.READ VALUE USING GTS (BRAKE WARNING LIGHT)
a.

Reinstall the reservoir filler cap and strainer.


b.

Reconnect the J1 combination meter assembly connector, A6 and A7 vacuum warning switch assembly connectors, F2 brake fluid level warning switch (brake master cylinder sub-assembly) connector and A71 skid control ECU (brake actuator assembly) connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


g.

According to the display on the GTS, read the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Brake Warning Light Brake warning light/ ON or OFF ON: Warning light on
OFF: Warning light off
-


h.

Check the GTS display condition of the brake warning light.


Result:
Result Proceed to
Display of the Data List remains OFF A
Display of the Data List remains ON B



A

B