Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2021.01
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356689 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Slip Indicator Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

The slip indicator light blinks during VSC and/or TRC operation.

If a malfunction is detected, the slip indicator light comes on to warn the driver (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DIAGNOSIS SYSTEM).

WIRING DIAGRAM

C372200E01
1.333,1.083 1.646,1.281 0.313,0.198 10 false 22 1.333,2.146 1.646,2.344 0.313,0.198 10 false 23 5.833,1.073 6.146,1.271 0.313,0.198 10 false 10 5.833,2.115 6.146,2.313 0.313,0.198 10 false 22 5.833,3.229 6.146,3.427 0.313,0.198 10 false 12 5.833,4.302 6.146,4.5 0.313,0.198 10 false 25 0.844,1.26 1.458,1.458 0.615,0.198 10 false CANL 0.844,2.302 1.458,2.5 0.615,0.198 10 false CANH 6.125,1.25 6.74,1.448 0.615,0.198 10 false CANL 6.125,2.292 6.74,2.49 0.615,0.198 10 false CANH 6.146,3.344 6.76,3.542 0.615,0.198 10 false IG1 6.125,4.406 6.74,4.604 0.615,0.198 10 false GND1 2.344,3.354 3.479,3.604 1.135,0.25 10 false from IG Circuit 4.24,3.51 6.229,3.708 1.99,0.198 10 false ECU-IG1 NO. 3 0.396,5.927 0.708,6.125 0.313,0.198 10 false J1 5.583,5.802 5.896,6 0.313,0.198 10 false A71 5.583,6.042 7.125,6.385 1.542,0.344 10 false Skid Control ECU (Brake Actuator Assembly) 0.396,6.083 1.583,6.469 1.188,0.385 10 false Combination Meter Assembly 2.823,6.385 4.885,6.667 2.063,0.281 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK CAN COMMUNICATION LINE
a.

Check if CAN communication system DTCs are output (Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).


Result:
Result Proceed to
DTC is not output A
DTC is output B



A

2.CHECK BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

2.CHECK BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.INSPECT BATTERY

NG

CONNECT CONNECTOR TO BRAKE ACTUATOR ASSEMBLY CORRECTLY

3.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V


HINT:
Refer to the inspection procedures:
Engine Type See page
N04C-VL (Click here)
N04C-VJ (Click here)
N04C-WA (Click here)



Result:
Proceed to
OK
NG



OK

4.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)

NG

CHECK OR REPLACE CHARGING SYSTEM OR BATTERY

4.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)
a.

Turn the ignition switch off.


b.
C399804E06
1.531,0.135 1.885,0.365 0.354,0.229 2.833,1.813 2.427,0.927 true 0.135,0.073 0.448,0.271 0.313,0.198 10 false *a 2.76,1.865 3.083,2.052 0.323,0.188 10 false IG1 1.594,0.167 1.979,0.406 0.385,0.24 10 false A71

Disconnect the A71 skid control ECU (brake actuator assembly) connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A71-12 (IG1) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
C399804E02
1.531,0.135 1.885,0.365 0.354,0.229 0.958,1.813 0.698,1.24 true 0.135,0.073 0.448,0.271 0.313,0.198 10 false *a 0.823,1.896 1.344,2.156 0.521,0.26 10 false GND1 1.594,0.167 1.979,0.406 0.385,0.24 10 false A71

Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A71-25 (GND1) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (SLIP INDICATOR LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

6.READ VALUE USING GTS (SLIP INDICATOR LIGHT)
a.

Reconnect the A71 skid control ECU (brake actuator assembly) connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the GTS, read the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Slip Indicator Light Slip indicator light / ON or OFF ON: Indicator light on
OFF: Indicator light off
-


g.

Check the GTS display condition of the slip indicator light.


Result:
Result Proceed to
Display of the Data List remains OFF A
Display of the Data List remains ON B



A

B