Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT AIRBAG SENSOR › from 2021.01
RM2850E _58 Vehicle Interior _073194 SUPPLEMENTAL RESTRAINT SYSTEMS _0356200 FRONT AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT AIRBAG SENSOR  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing.

for 2 Connectors Type:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 2 Connectors Type)>PRECAUTION

for 3 Connectors Type:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 3 Connectors Type)>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 58841A 3.REMOVE SHIFTING HOLE COVER (for Automatic Transmission)

Hide 33504F 4.REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transmission)

Hide 58534A 5.REMOVE TRANSMISSION COVER MAT (for Manual Transmission)

Hide 58286 6.REMOVE SHIFT LEVER BOOT (for Manual Transmission)

Hide 58123A 7.REMOVE SHIFT LEVER HOLE COVER (for Manual Transmission)

Hide 55433B 8.REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

Hide 55412D 9.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL

Hide 55470 10.REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY

Hide 55601C 11.REMOVE INSTRUMENT PANEL UNDER TRAY SUB-ASSEMBLY

Hide 89173 12.REMOVE FRONT AIRBAG SENSOR

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


i.

Push down the housing lock and slide the CPA. (At this time, the connector cannot be disconnected yet.)

B340847E01
2.594,0.5 3.135,0.5 3.135,0.5 3.646,0.75 true 4.302,0.917 4.583,0.594 4.583,0.594 4.99,0.594 true 3.479,1.583 3.76,1.583 3.76,1.583 3.76,1.271 true 3.292,1.5 3.604,1.698 0.313,0.198 10 false *b 5.052,0.51 5.365,0.708 0.313,0.198 10 false *a 2.438,0.417 2.75,0.615 0.313,0.198 10 false *c

Text in Illustration
*a Housing Lock *b CPA
*c CPA Upper Part - -


ii.

Push the housing lock again and disconnect the connector.

NOTICE:

Do not push down the upper part of the CPA shown in the illustration when disconnecting the airbag connector.



iii.

After disconnecting the connector, check that the position of the housing lock is correct as shown in the illustration.

B340848E02
1.385,0.531 1.698,0.729 0.313,0.198 10 false *a 4.823,0.542 5.135,0.74 0.313,0.198 10 false *a 1.385,1.781 1.698,1.979 0.313,0.198 10 false *b 4.844,1.823 5.156,2.021 0.313,0.198 10 false *b

Text in Illustration
*a Incorrect *b Correct



d.
B468051

Remove the bolt.

NOTICE:

Loosen the bolt while holding the front airbag sensor because the front airbag sensor guide is easily damaged.



e.

Detach the guide and remove the front airbag sensor.