Home › General › INTRODUCTION › WORK NOTICES AND PRECAUTIONS
BM24M0E _V1 General _059851 INTRODUCTION _0293729 WORK NOTICES AND PRECAUTIONS F

INTRODUCTION  WORK NOTICES AND PRECAUTIONS  NOTICE ABOUT VEHICLE CONDITION WHEN JACKING UP VEHICLE  


NOTICE ABOUT VEHICLE CONDITION WHEN JACKING UP VEHICLE


a.

The vehicle must be unloaded before jacking up / lifting up the vehicle. Never jack up / lift up a heavily loaded vehicle.


b.

When removing heavy parts such as the engine and transmission, the center of gravity of the vehicle may shift. To stabilize the vehicle, place a balance weight in a location where it will not roll or shift, or use a mission jack to hold the jacking support.



NOTICE FOR USING 4 POST LIFT


a.

Follow the safety procedures outlined in the lift instruction manual.


b.

Use precautionary measures to prevent the free wheel beam from damaging tires or wheels.


c.

Use wheel chocks to secure the vehicle.



NOTICE FOR USING JACK AND SAFETY STAND


a.

Work on a level surface. Use wheel chocks at all times.


b.
D101072E01
0.904,0.062 2.153,0.222 1.250,0.159 10 Rubber Attachment 0.845,0.146 0.591,0.146 0.591,0.146 1.652,1.431 false

Use safety stands with rubber attachments as shown in the illustration.


c.

Set the jack and safety stands to the specified locations of the vehicle accurately.


d.

When jacking up the vehicle, first release the parking brake and move the shift lever to N.


e.

When jacking up the entire vehicle:

·

When jacking up the front wheels first, make sure wheel chocks are behind the rear wheels.

·

When jacking up the rear wheels first, make sure wheel chocks are in front of the front wheels.



f.

When jacking up only the front or rear wheels of the vehicle:

·

Before jacking up the front wheels, place wheel chocks on both sides of the rear wheels.

·

Before jacking up the rear wheels, place wheel chocks on both sides of the front wheels.



g.

When lowering a vehicle that only has its front or rear wheels jacked up:

·

Before lowering the front wheels, make sure wheel chocks are in front of the rear wheels.

·

Before lowering the rear wheels, make sure wheel chocks are behind the front wheels.


U189793E01
0.596,1.909 1.092,2.135 0.496,0.225 10 Front 3.301,1.592 4.208,1.941 0.906,0.349 10 Do no jack up 4.247,1.661 4.977,1.661 false 3.202,1.661 2.451,1.661 false 5.115,1.109 4.678,1.109 false 4.678,2.234 5.115,2.234 false 4.678,1.109 4.678,2.236 false

D224452

JACK POSITION


Front: Engine under cover
Rear: Body lower back panel
CAUTION:

When jacking-up the vehicle, make sure the vehicle is not carrying any extra weight.


D224453

PANTOGRAPH JACK POSITION


-
D224454

SUPPORT POSITION


Safety stand and swing arm type lift
-


h.

It is extremely dangerous to perform any work on a vehicle raised on a jack alone, even for work that can be finished quickly. Safety stands must be used to support it.



NOTICE FOR USING SWING ARM TYPE LIFT


a.

Follow safety procedures outlined in its instruction manual.


b.

Use a swing arm equipped with a rubber attachment, as shown in the illustration.


c.

When using the lift, make sure that the vehicle is stabilized so that it will not tilt while work is being performed. Stabilize the vehicle by adjusting the lift arm's length and vehicle's position.


d.

When using the lift, its center should be as close to the vehicle's center of gravity as possible (length of "L" in the illustration should be as short as possible).

D101074E01
3.393,0.059 4.229,0.243 0.836,0.184 10 Center of Lift 5.85,2.915 7.099,3.080 1.248,0.165 10 Rubber Attachment 5.794,2.994 5.371,3.172 false 3.593,1.793 3.712,1.962 0.119,0.169 10 L


e.

Set the vehicle on the lift as level as possible. Then match the groove of the cradle to the safety stand support locations.


f.

Be sure to lock the swing arms before lifting and during work (if equipped with arm locks).


g.

Lift the vehicle up off the ground. Stand at a safe distance and shake the vehicle to check its stability.



NOTICE FOR USING PLATE TYPE LIFT


a.

Follow safety procedures outlined in its instruction manual.


b.

Use plate lift attachments (rubber lifting blocks) on top of the plate surface.


c.

Refer to the illustration below to determine how to properly set the vehicle.

U189794E02
2.479,2.823 2.969,2.75 false 3.802,2.75 4.458,2.823 false 2.5,1.25 2.5,1.917 false 4.458,1.26 4.458,1.927 false 2.604,1.406 4.344,1.406 false 3.052,2.656 3.865,2.844 0.813,0.188 10 false Attachment 1.146,3.875 2.688,4.031 1.542,0.156 10 false Attachment Dimensions 3.219,4.156 4.271,4.313 1.052,0.156 10 false 85 mm (3.35 in.) 3.479,5.396 4.615,5.552 1.135,0.156 10 false 200 mm (7.87 in.) 2.052,5.26 3.177,5.417 1.125,0.156 10 false 100 mm (3.94 in.) 4.646,4.771 5.698,4.927 1.052,0.156 10 false 70 mm (2.76 in.) 1.625,2.823 1.75,2.979 0.125,0.156 10 false A 5.229,2.833 5.354,2.99 0.125,0.156 10 false C 1.719,2.594 1.844,2.75 0.125,0.156 10 true B 2.021,3.219 2.417,3.375 0.396,0.156 10 false Front 4.583,3.219 4.979,3.375 0.396,0.156 10 false Rear 3.219,1.448 3.917,1.646 0.698,0.198 10 true 1370 mm

HINT:
Right and left set position Place the vehicle over the center of the lift.
Front and rear set position Place the attachments at the ends of the rubber plate surface, under the vehicle lift pad (A and C in the illustration). Raise the plate slightly and reposition the vehicle so the top of the attachment (B in the illustration) is aligned with the front side notch in the vehicle rocker flange.



d.

Use the lift to raise the vehicle up off the ground, and shake it to make sure that it is stable.