2013-2016 Previa Tarago Service Manual
2AZ-FE · 2GR-FE
Trouble codes (1404)
- P0010Open or short in camshaft timing oil control valve circuit (1 trip detection logic).
- P0010Open or short in camshaft timing oil control valve circuit (1 trip detection logic).
- P0011Intake valve timing is stuck at a certain value when in the advance range (1 trip detection logic).
- P0011Intake valve timing is stuck at a certain value when in the advance range (1 trip detection logic).
- P0011Intake valve timing is stuck at a certain value when in the advance range (1 trip detection logic).
- P0012Intake valve timing is stuck at a certain value when in the retard range (2 trip detection logic).
- P0012Intake valve timing is stuck at a certain value when in the retard range (2 trip detection logic).
- P0012Intake valve timing is stuck at a certain value when in the retard range (2 trip detection logic).
- P0016Deviation in crankshaft position sensor signal and camshaft position sensor signal (2 trip detection logic).
- P0016Deviation in crankshaft position sensor signal and camshaft position sensor signal (2 trip detection logic).
- P0016Deviation in crankshaft position sensor signal and camshaft position sensor signal (2 trip detection logic).
- P0031Air-Fuel Ratio (A/F) sensor heater current is less than the specified value while the heater is operating (1...
- P0031Air-Fuel Ratio (A/F) sensor heater current less than 0.8 A (1 trip detection logic)
- P0031Air-Fuel Ratio (A/F) sensor heater current less than 0.8 A (1 trip detection logic)
- P0032Air-Fuel Ratio (A/F) sensor heater current is specified value or higher while the heater is operating (1 trip...
- P0032Air-Fuel Ratio (A/F) sensor heater current reaches the high limit (1 trip detection logic)
- P0032Air-Fuel Ratio (A/F) sensor heater current reaches the high limit (1 trip detection logic)
- P0037Heated Oxygen (HO2) sensor heater current is less than the specified value while the heater is operating (1...
- P0037Heated Oxygen (HO2) sensor heater current less than 0.3 A (1 trip detection logic)
- P0038Heated Oxygen (HO2) sensor heater current is specified value or higher while the heater is operating (1 trip...
- P0038Heated Oxygen (HO2) sensor heater current reaches high limit (1 trip detection logic)
- P0100MAF meter voltage is less than the specified value, or more than the specified value for 3 seconds or more (1...
- P0100MAF meter voltage less than 0.2 V, or more than 4.9 V for 3 seconds (1 trip detection logic)
- P0102MAF meter voltage is less than the specified value for 3 seconds or more (1 trip detection logic)
- P0102MAF meter voltage less than 0.2 V for 3 seconds (1 trip detection logic)
- P0103MAF meter voltage is more than the specified value for 3 seconds or more (1 trip detection logic)
- P0103MAF meter voltage more than 4.9 V for 3 seconds (1 trip detection logic)
- P0110Open or short in IAT sensor circuit for 0.5 seconds (1 trip detection logic)
- P0110Open or short in IAT sensor circuit for 0.5 seconds (1 trip detection logic)
- P0112Short in IAT sensor circuit for 0.5 seconds (1 trip detection logic)
- P0112Short in IAT sensor circuit for 0.5 seconds (1 trip detection logic)
- P0113Open in IAT sensor circuit for 0.5 seconds (1 trip detection logic)
- P0113Open in IAT sensor circuit for 0.5 seconds (1 trip detection logic)
- P0115Open or short in ECT sensor circuit for 0.5 seconds (1 trip detection logic)
- P0115Open or short in ECT sensor circuit for 0.5 seconds (1 trip detection logic)
- P0116Engine Coolant Temperature (ECT) between -40°C and 60°C (-40°F and 140°F) when engine started, and conditions...
- P0116Engine Coolant Temperature (ECT) between -40°C and 60°C (-40°F and 140°F) when engine started, and conditions...
- P0116Euro-OBD: Either of the following conditions is met (2 trip detection logic): · When engine is started cold...
- P0117Short in ECT sensor circuit for 0.5 seconds (1 trip detection logic)
- P0117Short in ECT sensor circuit for 0.5 seconds (1 trip detection logic)
- P0118Open in ECT sensor circuit for 0.5 seconds (1 trip detection logic)
- P0118Open in ECT sensor circuit for 0.5 seconds (1 trip detection logic)
- P0120The output voltage of VTA1 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds...
- P0120The output voltage of VTA1 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds...
- P0121The difference between the VTA1 and VTA2 voltages is less than 0.8 V, or higher than 1.6 V for 2 seconds (1...
- P0121The difference between the VTA1 and VTA2 voltages is less than 0.8 V, or higher than 1.6 V for 2 seconds (1...
- P0122The output voltage of VTA1 is 0.2 V or less for 2 seconds or more (1 trip detection logic).
- P0122The output voltage of VTA1 is 0.2 V or less for 2 seconds or more (1 trip detection logic).
- P0123The output voltage of VTA1 is 4.54 V or higher for 2 seconds or more (1 trip detection logic).
- P0123The output voltage of VTA1 is 4.54 V or higher for 2 seconds or more (1 trip detection logic).
- P0136Abnormal voltage output: During active air fuel ratio control, the following conditions (a) and (b) are met...
- P0136Abnormal voltage output: During active air fuel ratio control, the following conditions (a) and (b) are met...
- P0136Abnormal voltage output: During active air fuel ratio control, the following conditions (a) and (b) are met...
- P0137Low voltage (open): During active air fuel ratio control, the following conditions (a) and (b) are met for a...
- P0137Low voltage (open): During active air fuel ratio control, the following conditions (a) and (b) are met for a...
- P0137Low voltage (open): During active air fuel ratio control, the following conditions (a) and (b) are met for a...
- P0138High voltage (short): During active air fuel ratio control, the following conditions (a) and (b) are met for...
- P0138High voltage (short): During active air fuel ratio control, the following conditions (a) and (b) are met for...
- P0138High voltage (short): During active air fuel ratio control, the following conditions (a) and (b) are met for...
- P0171With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the lean...
- P0171With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the lean...
- P0171With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the lean...
- P0172With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the rich...
- P0172With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the rich...
- P0172With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the rich...
- P0220The output voltage of VTA2 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds...
- P0220The output voltage of VTA2 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds...
- P0222The output voltage of VTA2 is 1.75 V or less for 2 seconds or more (1 trip detection logic).
- P0222The output voltage of VTA2 is 1.75 V or less for 2 seconds or more (1 trip detection logic).
- P0223The output voltage of VTA2 is 4.8 V or higher, and VTA1 is between 0.2 V and 2.02 V for 2 seconds or more (1...
- P0223The output voltage of VTA2 is 4.8 V or higher, and VTA1 is between 0.2 V and 2.02 V for 2 seconds or more (1...
- P0300Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip...
- P0300Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip...
- P0300Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip...
- P0301Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):...
- P0301Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):...
- P0301Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):...
- P0302Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):...
- P0302Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):...
- P0302Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):...
- P0303Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):...
- P0303Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):...
- P0303Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):...
- P0304Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):...
- P0304Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):...
- P0304Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):...
- P0327Output voltage of knock sensor is 0.5 V or less (1 trip detection logic)
- P0327Output voltage of knock sensor is 0.5 V or less (1 trip detection logic)
- P0328Output voltage of knock sensor is 4.5 V or more (1 trip detection logic)
- P0328Output voltage of knock sensor is 4.5 V or more (1 trip detection logic)
- P0335One of the following conditions is met (1 trip detection logic): · No crankshaft position sensor signal to...
- P0335One of the following conditions is met (1 trip detection logic): · No crankshaft position sensor signal to...
- P0339All of the following conditions are met (1 trip detection logic): (a) The engine speed is 1000 rpm or higher....
- P0339All of the following conditions are met (1 trip detection logic): (a) The engine speed is 1000 rpm or higher....
- P0340When one of the following conditions is met: · A missing camshaft position sensor signal despite the...
- P0340When one of the following conditions is met: · A missing camshaft position sensor signal despite the...
- P0351No IGF signal to ECM while engine running (1 trip detection logic)
- P0351No IGF signal to ECM while engine running (1 trip detection logic)
- P0352No IGF signal to ECM while engine running (1 trip detection logic)
- P0352No IGF signal to ECM while engine running (1 trip detection logic)
- P0353No IGF signal to ECM while engine running (1 trip detection logic)
- P0353No IGF signal to ECM while engine running (1 trip detection logic)
- P0354No IGF signal to ECM while engine running (1 trip detection logic)
- P0354No IGF signal to ECM while engine running (1 trip detection logic)
- P0420The oxygen storage capacity value is less than the standard value under active air fuel ratio control (2 trip...
- P0420The oxygen storage capacity value is less than the standard value under active air fuel ratio control (2 trip...
- P0420The oxygen storage capacity value is less than the standard value under active air fuel ratio control (2 trip...
- P0443Both of the following conditions (a) and (b) are met (1 trip detection logic): (a) The target control value...
- P0443Both of the following conditions (a) and (b) are met (1 trip detection logic): (a) The target control value...
- P0500While vehicle being driven, no vehicle speed sensor signal transmitted to ECM (1 trip detection logic).
- P0500for CVT models: Either of the following conditions (a) and (b) is met for 2.0 seconds or more (1 trip...
- P0504Conditions (a) and (b) continue for 0.5 seconds or more (1 trip detection logic): (a) Engine switch on (IG)...
- P0504Conditions (a) and (b) continue for 0.5 seconds or more (1 trip detection logic): (a) Engine switch on (IG)...
- P0516Battery temperature sensor output value is 0.2 V or less for 0.5 seconds or more with the engine switch on...
- P0516Battery temperature sensor output value is 0.2 V or less for 0.5 seconds or more with the engine switch on...
- P0517Battery temperature sensor output value is 4.8 V or more for 0.5 seconds or more with the engine switch on...
- P0517Battery temperature sensor output value is 4.8 V or more for 0.5 seconds or more with the engine switch on...
- P0560Open in ECM back-up power source circuit (1 trip detection logic)
- P0560Open in ECM back-up power source circuit (1 trip detection logic)
- P0604ECM internal error (1 trip detection logic)
- P0604ECM internal error (1 trip detection logic)
- P0604ECM internal error (1 trip detection logic)
- P0606ECM internal error (1 trip detection logic)
- P0606ECM internal error (1 trip detection logic)
- P0606ECM internal error (1 trip detection logic)
- P0607ECM internal error (1 trip detection logic)
- P0607ECM internal error (1 trip detection logic)
- P0607ECM internal error (1 trip detection logic)
- P060AECM internal error (1 trip detection logic)
- P060AECM internal error (1 trip detection logic)
- P060AECM internal error (1 trip detection logic)
- P060DECM internal error (1 trip detection logic)
- P060DECM internal error (1 trip detection logic)
- P060DECM internal error (1 trip detection logic)
- P060EECM internal error (1 trip detection logic)
- P060EECM internal error (1 trip detection logic)
- P060EECM internal error (1 trip detection logic)
- P0617When all of the following conditions are met, and a (+B) battery voltage of 10.5 V or higher is applied to...
- P0617When conditions (a), (b) and (c) are met, positive (+B) battery voltage 10.5 V or more is applied to ECM for...
- P0617When conditions (a), (b) and (c) are met, positive (+B) battery voltage 10.5 V or more is applied to ECM for...
- P0630Either of the following conditions is met (1 trip detection logic): · The VIN is not stored in the ECM. · The...
- P0630Either of the following conditions is met (1 trip detection logic): · The VIN or frame number is not stored...
- P0657ECM internal error (1 trip detection logic)
- P0657ECM internal error (1 trip detection logic)
- P0657ECM internal error (1 trip detection logic)
- P0724The stop light switch remains on even when the vehicle repeats 5 cycles of STOP (less than 3 km/h [1.86 mph])...
- P0724The stop light switch remains on even when the vehicle repeats 5 cycles of STOP (less than 3 km/h [1.86 mph])...
- P1550The following condition continues for 10 seconds or more with the engine switch on (IG) (1 trip detection...
- P1550The following condition continues for 10 seconds or more with the engine switch on (IG) (1 trip detection...
- P1551Battery current sensor output value is 0.2 V or less for 0.5 seconds or more with the engine switch on (IG)...
- P1551Battery current sensor output voltage is 0.2 V or less for 0.5 seconds or more with the engine switch on (IG)...
- P1552Battery current sensor output value is 4.8 V or more for 0.5 seconds or more with the engine switch on (IG)...
- P1552Battery current sensor output voltage is 4.8 V or more for 0.5 seconds or more with the engine switch on (IG)...
- P1602Battery power is 0%
- P1602Battery voltage is low for 10 seconds or more when the engine is running (not cranking) (1 trip detection...
- P1603After monitoring for startability problems (P1604) finishes and 5 seconds or more elapse after starting the...
- P1603After monitoring for startability problems (P1604) finishes and 5 seconds or more elapse after starting the...
- P1603After monitoring for startability problems (P1604) finishes and 5 seconds or more elapse after starting the...
- P1604Either condition is met: · The engine speed is below 500 rpm with the STA signal on for a certain amount of...
- P1604Either condition is met: · The engine speed is below 500 rpm with the STA signal on for a certain amount of...
- P1604Either condition is met: · The engine speed is below 500 rpm with the STA signal on for a certain amount of...
- P1605After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to...
- P1605After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to...
- P1605After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to...
- P1607ECM internal error (1 trip detection logic)
- P1607ECM internal error (1 trip detection logic)
- P1607ECM internal error (1 trip detection logic)
- P2102Both of the following conditions continue for 2.0 seconds (1 trip detection logic): (a) The throttle actuator...
- P2102Both of the following conditions continue for 2.0 seconds (1 trip detection logic): (a) The throttle actuator...
- P2103Either of the following conditions is met (1 trip detection logic): · A hybrid IC diagnosis signal failure. ·...
- P2103Either of the following conditions is met (1 trip detection logic): · A hybrid IC diagnosis signal failure. ·...
- P2109The ISC learned value is approximately 3 times larger than normal even though the actual intake air amount...
- P2109The ISC learned value is approximately 3 times larger than normal even though the actual intake air amount...
- P2109The ISC learned value is approximately 3 times larger than normal even though the actual intake air amount...
- P2111The ECM signals the throttle actuator to close, but the actuator is stuck (1 trip detection logic).
- P2111The ECM signals the throttle actuator to close, but the actuator is stuck (1 trip detection logic).
- P2111The ECM signals the throttle actuator to close, but the actuator is stuck (1 trip detection logic).
- P2112The ECM signals the throttle actuator to open, but the actuator is stuck (1 trip detection logic).
- P2112The ECM signals the throttle actuator to open, but the actuator is stuck (1 trip detection logic).
- P2112The ECM signals the throttle actuator to open, but the actuator is stuck (1 trip detection logic).
- P2118Open in ETCS power source (+BM) circuit (1 trip detection logic)
- P2118Open in ETCS power source (+BM) circuit (1 trip detection logic)
- P2119The throttle valve opening angle continues to vary greatly from the target opening angle (1 trip detection...
- P2119The throttle valve opening angle continues to vary greatly from the target opening angle (1 trip detection...
- P2119The throttle valve opening angle continues to vary greatly from the target opening angle (1 trip detection...
- P2120VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip...
- P2120VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip...
- P2121Either of following conditions 1 or 2 met for 0.5 seconds (1 trip detection logic): 1. Difference between VPA...
- P2121Either of following conditions 1 or 2 met for 0.5 seconds (1 trip detection logic): 1. Difference between VPA...
- P2121Either of following conditions 1 or 2 met for 0.5 seconds (1 trip detection logic): 1. Difference between VPA...
- P2122VPA 0.4 V or less for 0.5 seconds or more when accelerator pedal depressed (1 trip detection logic)
- P2122VPA 0.4 V or less for 0.5 seconds or more when accelerator pedal depressed (1 trip detection logic)
- P2123VPA 4.8 V or more for 2.0 seconds or more (1 trip detection logic)
- P2123VPA 4.8 V or more for 2.0 seconds or more (1 trip detection logic)
- P2125VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip...
- P2125VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip...
- P2127VPA2 1.2 V or less for 0.5 seconds or more when accelerator pedal depressed (1 trip detection logic)
- P2127VPA2 1.2 V or less for 0.5 seconds or more when accelerator pedal depressed (1 trip detection logic)
- P2128Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic): (a) VPA2 4.8 V or more (b)...
- P2128Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic): (a) VPA2 4.8 V or more (b)...
- P2135Either of the following conditions is met (1 trip detection logic): (a) The difference between the output...
- P2135Either of the following conditions is met (1 trip detection logic): (a) The difference between the output...
- P2138Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic): (a) Difference between VPA...
- P2138Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic): (a) Difference between VPA...
- P2195Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2195Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2195Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2196Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2196Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2196Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2237An open in the circuit between terminals A1A+ and A1A- of the air fuel ratio sensor while the engine is...
- P2237An open in the circuit between terminals A1A+ and A1A- of the air fuel ratio sensor while the engine is...
- P2237An open or short in the circuit between terminals A1A+ and A1A- of the air fuel ratio sensor while the engine...
- P2238· Case 1: Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) Voltage at...
- P2238· Case 1: Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) Voltage at...
- P2238· Case 1: Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) Voltage at...
- P2239The A1A+ voltage is higher than 4.5 V (2 trip detection logic).
- P2239The A1A+ voltage is higher than 4.5 V (2 trip detection logic).
- P2239The A1A+ voltage is higher than 4.5 V (2 trip detection logic).
- P2252The A1A- voltage is 0.5 V or less (2 trip detection logic).
- P2252The A1A- voltage is 0.5 V or less (2 trip detection logic).
- P2252The A1A- voltage is 0.5 V or less (2 trip detection logic).
- P2253The A1A- voltage is higher than 4.5 V (2 trip detection logic).
- P2253The A1A- voltage is higher than 4.5 V (2 trip detection logic).
- P2253The A1A- voltage is higher than 4.5 V (2 trip detection logic).
- P2610ECM internal malfunction (2 trip detection logic).
- P2610ECM internal malfunction (2 trip detection logic).
- P2A00The calculated value for the air fuel ratio sensor response rate deterioration level is less than the...
- P2A00The calculated value for the air fuel ratio sensor response rate deterioration level is less than the...
- P2A00The calculated value for the air fuel ratio sensor response rate deterioration level is less than the...
- U0129All of following conditions met for 2.40 seconds or more (1 trip detection logic): · Engine switch on (IG) ·...
- U0129All of following conditions met for 2.40 seconds or more (1 trip detection logic): · Engine switch on (IG) ·...
- P0010Open or short in camshaft timing oil control valve assembly (for intake camshaft of bank 1) circuit (1 trip...
- P0011Advanced cam timing: With engine warmed up and engine speed of between 500 rpm and 4000 rpm, all conditions...
- P0011Advanced cam timing: With engine warmed up and engine speed of between 500 rpm and 4000 rpm, all conditions...
- P0011Advanced cam timing: With engine warmed up and engine speed of between 500 rpm and 4000 rpm, all conditions...
- P0012Retarded cam timing: With engine warmed up and engine speed of between 500 rpm and 4000 rpm, all conditions...
- P0012Retarded cam timing: With engine warmed up and engine speed of between 500 rpm and 4000 rpm, all conditions...
- P0012Retarded cam timing: With engine warmed up and engine speed of between 500 rpm and 4000 rpm, all conditions...
- P0013Open or short in camshaft timing oil control valve assembly (for exhaust camshaft of bank 1) circuit (1 trip...
- P0013Open or short in camshaft timing oil control valve assembly (for exhaust camshaft of bank 1) circuit (1 trip...
- P0014Advanced cam timing: With engine warmed up and engine speed of between 500 rpm and 4000 rpm, all conditions...
- P0014Advanced cam timing: With engine warmed up and engine speed of between 500 rpm and 4000 rpm, all conditions...
- P0014Advanced cam timing: With engine warmed up and engine speed of between 500 rpm and 4000 rpm, all conditions...
- P0015Retarded cam timing: With engine warmed up and engine speed of between 500 rpm and 4000 rpm, all conditions...
- P0015Retarded cam timing: With engine warmed up and engine speed of between 500 rpm and 4000 rpm, all conditions...
- P0015Retarded cam timing: With engine warmed up and engine speed of between 500 rpm and 4000 rpm, all conditions...
- P0016Deviation in crankshaft position sensor signal and VVT sensor (for intake camshaft of bank 1) signal (2 trip...
- P0016Deviation in crankshaft position sensor signal and VVT sensor (for intake camshaft of bank 1) signal (2 trip...
- P0016Deviation in crankshaft position sensor signal and VVT sensor (for intake camshaft of bank 1) signal (2 trip...
- P0017Deviation in crankshaft position sensor signal and VVT sensor (for exhaust camshaft of bank 1) signal (2 trip...
- P0017Deviation in crankshaft position sensor signal and VVT sensor (for exhaust camshaft of bank 1) signal (2 trip...
- P0017Deviation in crankshaft position sensor signal and VVT sensor (for exhaust camshaft of bank 1) signal (2 trip...
- P0018Deviation in crankshaft position sensor signal and VVT sensor (for intake camshaft of bank 2) signal (2 trip...
- P0018Deviation in crankshaft position sensor signal and VVT sensor (for intake camshaft of bank 2) signal (2 trip...
- P0018Deviation in crankshaft position sensor signal and VVT sensor (for intake camshaft of bank 2) signal (2 trip...
- P0019Deviation in crankshaft position sensor signal and VVT sensor (for exhaust camshaft of bank 2) signal (2 trip...
- P0019Deviation in crankshaft position sensor signal and VVT sensor (for exhaust camshaft of bank 2) signal (2 trip...
- P0019Deviation in crankshaft position sensor signal and VVT sensor (for exhaust camshaft of bank 2) signal (2 trip...
- P0020Open or short in camshaft timing oil control valve assembly (for intake camshaft of bank 2) circuit (1 trip...
- P0021Advanced cam timing: With engine warmed up and engine speed of between 500 rpm and 4000 rpm, all conditions...
- P0021Advanced cam timing: With engine warmed up and engine speed of between 500 rpm and 4000 rpm, all conditions...
- P0021Advanced cam timing: With engine warmed up and engine speed of between 500 rpm and 4000 rpm, all conditions...
- P0022Retarded cam timing: With engine warmed up and engine speed of between 500 rpm and 4000 rpm, all conditions...
- P0022Retarded cam timing: With engine warmed up and engine speed of between 500 rpm and 4000 rpm, all conditions...
- P0022Retarded cam timing: With engine warmed up and engine speed of between 500 rpm and 4000 rpm, all conditions...
- P0023Open or short in camshaft timing oil control valve assembly (for exhaust camshaft of bank 2) circuit (1 trip...
- P0023Open or short in camshaft timing oil control valve assembly (for exhaust camshaft of bank 2) circuit (1 trip...
- P0024Advanced cam timing: With engine warmed up and engine speed of between 500 rpm and 4000 rpm, all conditions...
- P0024Advanced cam timing: With engine warmed up and engine speed of between 500 rpm and 4000 rpm, all conditions...
- P0024Advanced cam timing: With engine warmed up and engine speed of between 500 rpm and 4000 rpm, all conditions...
- P0025Retarded cam timing: With engine warmed up and engine speed of between 500 rpm and 4000 rpm, all conditions...
- P0025Retarded cam timing: With engine warmed up and engine speed of between 500 rpm and 4000 rpm, all conditions...
- P0025Retarded cam timing: With engine warmed up and engine speed of between 500 rpm and 4000 rpm, all conditions...
- P0031Air fuel ratio sensor heater current is less than 0.8 A (1 trip detection logic).
- P0031Air fuel ratio sensor heater current is less than 0.8 A (1 trip detection logic).
- P0032Air fuel ratio sensor heater current reaches the high limit (1 trip detection logic).
- P0032Air fuel ratio sensor heater current reaches the high limit (1 trip detection logic).
- P0037Heated oxygen sensor heater current is the specified value or less while the heater is operating (1 trip...
- P0038Heated oxygen sensor heater current reaches high limit (1 trip detection logic).
- P0051Air fuel ratio sensor heater current is less than 0.8 A (1 trip detection logic).
- P0051Air fuel ratio sensor heater current is less than 0.8 A (1 trip detection logic).
- P0052Air fuel ratio sensor heater current reaches the high limit (1 trip detection logic).
- P0052Air fuel ratio sensor heater current reaches the high limit (1 trip detection logic).
- P0057Heated oxygen sensor heater current is the specified value or less while the heater is operating (1 trip...
- P0058Heated oxygen sensor heater current reaches high limit (1 trip detection logic).
- P0100Open or short in mass air flow meter sub-assembly circuit for 3 seconds (1 trip detection logic)
- P0102Open in mass air flow meter sub-assembly circuit for 3 seconds (1 trip detection logic)
- P0103Short in mass air flow meter sub-assembly circuit for 3 seconds (1 trip detection logic)
- P0110Open or short in intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic)
- P0112Short in intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic)
- P0113Open in intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic)
- P0115Open or short in engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic)
- P0116ECTs as listed below are nearly same (2 trip detection logic): - ECT when engine is started at lower than...
- P0116ECTs as listed below are nearly same (2 trip detection logic): - ECT when engine is started at lower than...
- P0116Either of the following conditions is met (2 trip detection logic): · When engine is started cold and warmed...
- P0117Short in engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic)
- P0118Open in engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic)
- P0120The output voltage of VTA1 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds...
- P0121The difference between the VTA1 and VTA2 voltages is less than 0.8 V, or higher than 1.6 V for 2 seconds (1...
- P0122The output voltage of VTA1 is 0.2 V or less for 2 seconds or more (1 trip detection logic).
- P0123The output voltage of VTA1 is 4.54 V or higher for 2 seconds or more (1 trip detection logic).
- P0136Abnormal voltage output: During active air fuel ratio control, following conditions (a) and (b) are met for a...
- P0136Abnormal voltage output: During active air fuel ratio control, following conditions (a) and (b) are met for a...
- P0136Abnormal voltage output: During active air fuel ratio control, following conditions (a) and (b) are met for a...
- P0137Low voltage (open): During active air fuel ratio control, following conditions (a) and (b) are met for a...
- P0137Low voltage (open): During active air fuel ratio control, following conditions (a) and (b) are met for a...
- P0137Low voltage (open): During active air fuel ratio control, following conditions (a) and (b) are met for a...
- P0138High voltage (short): During active air fuel ratio control, following conditions (a) and (b) are met for a...
- P0138High voltage (short): During active air fuel ratio control, following conditions (a) and (b) are met for a...
- P0138High voltage (short): During active air fuel ratio control, following conditions (a) and (b) are met for a...
- P0156Abnormal voltage output: During active air fuel ratio control, following conditions (a) and (b) are met for a...
- P0156Abnormal voltage output: During active air fuel ratio control, following conditions (a) and (b) are met for a...
- P0156Abnormal voltage output: During active air fuel ratio control, following conditions (a) and (b) are met for a...
- P0157Low voltage (open): During active air fuel ratio control, following conditions (a) and (b) are met for a...
- P0157Low voltage (open): During active air fuel ratio control, following conditions (a) and (b) are met for a...
- P0157Low voltage (open): During active air fuel ratio control, following conditions (a) and (b) are met for a...
- P0158High voltage (short): During active air fuel ratio control, following conditions (a) and (b) are met for a...
- P0158High voltage (short): During active air fuel ratio control, following conditions (a) and (b) are met for a...
- P0158High voltage (short): During active air fuel ratio control, following conditions (a) and (b) are met for a...
- P0171With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the lean...
- P0171With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the lean...
- P0171With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the lean...
- P0172With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the rich...
- P0172With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the rich...
- P0172With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the rich...
- P0174With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the lean...
- P0174With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the lean...
- P0174With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the lean...
- P0175With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the rich...
- P0175With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the rich...
- P0175With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the rich...
- P0220The output voltage of VTA2 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds...
- P0222The output voltage of VTA2 is 1.75 V or less for 2 seconds or more (1 trip detection logic).
- P0223The output voltage of VTA2 is 4.8 V or higher, and VTA1 is between 0.2 V and 2.02 V for 2 seconds or more (1...
- P0230Open or short in F/PMP relay circuit (1 trip detection logic)
- P0300Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip...
- P0300Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip...
- P0300Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip...
- P0301Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):...
- P0301Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):...
- P0301Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):...
- P0302Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):...
- P0302Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):...
- P0302Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):...
- P0303Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):...
- P0303Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):...
- P0303Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):...
- P0304Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):...
- P0304Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):...
- P0304Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):...
- P0305Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):...
- P0305Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):...
- P0305Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):...
- P0306Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):...
- P0306Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):...
- P0306Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):...
- P0327Output voltage of knock sensor 1 or 2 is 0.5 V or less (1 trip detection logic)
- P0327Output voltage of knock sensor 1 or 2 is 0.5 V or less (1 trip detection logic)
- P0328Output voltage of knock sensor 1 or 2 is 4.5 V or more (1 trip detection logic)
- P0328Output voltage of knock sensor 1 or 2 is 4.5 V or more (1 trip detection logic)
- P0332Output voltage of knock sensor 1 or 2 is 0.5 V or less (1 trip detection logic)
- P0332Output voltage of knock sensor 1 or 2 is 0.5 V or less (1 trip detection logic)
- P0333Output voltage of knock sensor 1 or 2 is 4.5 V or more (1 trip detection logic)
- P0333Output voltage of knock sensor 1 or 2 is 4.5 V or more (1 trip detection logic)
- P0335· No CKP sensor signal to ECM while cranking (1 trip detection logic) · No CKP sensor signal to ECM at engine...
- P0339Under conditions (a), (b) and (c), no crankshaft position sensor signal to ECM for 0.05 seconds or more (1...
- P0340· Input voltage to ECM remains 0.3 V or less, or 4.7 V or higher for more than 5 seconds, when 2 or more...
- P0342The output voltage of the VVT sensor is less than 0.3 V for 5 seconds (1 trip detection logic).
- P0343The output voltage of the VVT sensor is higher than 4.7 V for 5 seconds (1 trip detection logic).
- P0345· Input voltage to ECM remains 0.3 V or less, or 4.7 V or higher for more than 5 seconds, when 2 or more...
- P0347The output voltage of the VVT sensor is less than 0.3 V for 5 seconds (1 trip detection logic).
- P0348The output voltage of the VVT sensor is higher than 4.7 V for 5 seconds (1 trip detection logic).
- P0351No IGF signal to ECM while engine is running (1 trip detection logic)
- P0351No IGF signal to ECM while engine is running (1 trip detection logic)
- P0352No IGF signal to ECM while engine is running (1 trip detection logic)
- P0352No IGF signal to ECM while engine is running (1 trip detection logic)
- P0353No IGF signal to ECM while engine is running (1 trip detection logic)
- P0353No IGF signal to ECM while engine is running (1 trip detection logic)
- P0354No IGF signal to ECM while engine is running (1 trip detection logic)
- P0354No IGF signal to ECM while engine is running (1 trip detection logic)
- P0355No IGF signal to ECM while engine is running (1 trip detection logic)
- P0355No IGF signal to ECM while engine is running (1 trip detection logic)
- P0356No IGF signal to ECM while engine is running (1 trip detection logic)
- P0356No IGF signal to ECM while engine is running (1 trip detection logic)
- P0365· Input voltage to ECM remains 0.3 V or less, or 4.7 V or higher for more than 5 seconds, when 2 or more...
- P0367The output voltage of the exhaust VVT sensor (bank 1, 2) is less than 0.3 V for 5 seconds (1 trip detection...
- P0368The output voltage of the exhaust VVT sensor (bank 1, 2) is higher than 4.7 V for 5 seconds (1 trip detection...
- P0390· Input voltage to ECM remains 0.3 V or less, or 4.7 V or higher for more than 5 seconds, when 2 or more...
- P0392The output voltage of the exhaust VVT sensor (bank 1, 2) is less than 0.3 V for 5 seconds (1 trip detection...
- P0393The output voltage of the exhaust VVT sensor (bank 1, 2) is higher than 4.7 V for 5 seconds (1 trip detection...
- P0420The oxygen storage capacity value is less than the standard value under active air fuel ratio control (2 trip...
- P0420The oxygen storage capacity value is less than the standard value under active air fuel ratio control (2 trip...
- P0420The oxygen storage capacity value is less than the standard value under active air fuel ratio control (2 trip...
- P0430The oxygen storage capacity value is less than the standard value under active air fuel ratio control (2 trip...
- P0430The oxygen storage capacity value is less than the standard value under active air fuel ratio control (2 trip...
- P0430The oxygen storage capacity value is less than the standard value under active air fuel ratio control (2 trip...
- P0443Terminal voltage of ECM output circuit does not correspond with drive signals from ECM to purge VSV (1 trip...
- P0500While vehicle being driven, no vehicle speed sensor signal to ECM (1 trip detection logic).
- P0500While vehicle being driven, no vehicle speed sensor signal to ECM (1 trip detection logic).
- P0504Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic): (a) Engine switch on...
- P0504Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic): (a) Engine switch on...
- P0505Idle speed continues to vary greatly from target idle speed (2 trip detection logic)
- P0505Idle speed continues to vary greatly from target idle speed (2 trip detection logic)
- P0516Battery temperature sensor output value is 0.2 V or less for 0.5 seconds or more with the engine switch on...
- P0517Battery temperature sensor output value is 4.8 V or more for 0.5 seconds or more with the engine switch on...
- P0560Open in ECM back-up power source circuit (1 trip detection logic).
- P0604ECM internal error (1 trip detection logic)
- P0606ECM internal error (1 trip detection logic)
- P0607ECM internal error (1 trip detection logic)
- P0617When all of the following conditions are met, and a (+B) battery voltage of 10.5 V or higher is applied to...
- P0617When all of the following conditions are met, and a (+B) battery voltage of 10.5 V or higher is applied to...
- P0630Either of the following conditions is met (1 trip detection logic): · The VIN or frame number is not stored...
- P0657ECM internal error (1 trip detection logic)
- P0660The following conditions are met simultaneously for 0.5 seconds or more (2 trip detection logic): 1. Voltage...
- P0705(A) Any 2 or more signals of the following are ON simultaneously (2 trip detection logic): · P input signal ·...
- P0705(A) Any 2 or more signals of the following are ON simultaneously (2 trip detection logic): · P input signal ·...
- P0724The stop light switch assembly remains on even when the vehicle repeats 5 cycles of STOP (less than 3 km/h...
- P0724The stop light switch assembly remains on even when the vehicle repeats 5 cycles of STOP (less than 3 km/h...
- P101DAir fuel ratio sensor heater current is higher than the specified value while the heater is not operating (1...
- P101DAir fuel ratio sensor heater current is higher than the specified value while the heater is not operating (1...
- P102DHeated oxygen sensor heater current is higher than the specified value while the heater is not operating (1...
- P103DAir fuel ratio sensor heater current is higher than the specified value while the heater is not operating (1...
- P103DAir fuel ratio sensor heater current is higher than the specified value while the heater is not operating (1...
- P105DHeated oxygen sensor heater current is higher than the specified value while the heater is not operating (1...
- P1550The following condition continues for 10 seconds or more with the engine switch on (IG) (1 trip detection...
- P1551Battery current sensor output value is 0.2 V or less for 0.5 seconds or more with the engine switch on (IG)...
- P1552Battery current sensor output value is 4.8 V or more for 0.5 seconds or more with the engine switch on (IG)...
- P15851. Engine switch on (IG). 2. The output value of the yaw rate sensor remains at -1.5 G or less, or 1.5 G or...
- P15851. Engine switch on (IG). 2. The output value of the yaw rate sensor remains at -1.5 G or less, or 1.5 G or...
- P15851. Engine switch on (IG). 2. The output value of the yaw rate sensor remains at -1.5 G or less, or 1.5 G or...
- P15861. Engine switch on (IG) 2. With the vehicle speed 30 km/h (18 mph) or more, the difference between the...
- P15861. Engine switch on (IG) 2. With the vehicle speed 30 km/h (18 mph) or more, the difference between the...
- P15861. Engine switch on (IG) 2. With the vehicle speed 30 km/h (18 mph) or more, the difference between the...
- P15891. The vehicle speed is 2 km/h (1.2 mph) or more. 2. The yaw rate sensor calibration (deceleration sensor...
- P15891. The vehicle speed is 2 km/h (1.2 mph) or more. 2. The yaw rate sensor calibration (deceleration sensor...
- P15891. The vehicle speed is 2 km/h (1.2 mph) or more. 2. The yaw rate sensor calibration (deceleration sensor...
- P1602Battery power is 0%
- P1603After monitoring for startability problems (P1604) finishes and 5 seconds or more elapse after starting the...
- P1603After monitoring for startability problems (P1604) finishes and 5 seconds or more elapse after starting the...
- P1603After monitoring for startability problems (P1604) finishes and 5 seconds or more elapse after starting the...
- P1604Either condition is met: · The engine speed is below 500 rpm with the STA signal on for a certain amount of...
- P1604Either condition is met: · The engine speed is below 500 rpm with the STA signal on for a certain amount of...
- P1604Either condition is met: · The engine speed is below 500 rpm with the STA signal on for a certain amount of...
- P1605After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to...
- P1605After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to...
- P1605After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to...
- P2102Both of the following conditions continue for 2.0 seconds (1 trip detection logic): (a) The throttle actuator...
- P2103Either of the following conditions is met (1 trip detection logic): · A hybrid IC diagnosis signal failure. ·...
- P2109The ISC learned value is approximately 3 times larger than normal even though the actual intake air amount...
- P2109The ISC learned value is approximately 3 times larger than normal even though the actual intake air amount...
- P2109The ISC learned value is approximately 3 times larger than normal even though the actual intake air amount...
- P2111The ECM signals the throttle actuator to close, but the actuator is stuck (1 trip detection logic).
- P2111The ECM signals the throttle actuator to close, but the actuator is stuck (1 trip detection logic).
- P2111The ECM signals the throttle actuator to close, but the actuator is stuck (1 trip detection logic).
- P2112The ECM signals the throttle actuator to open, but the actuator is stuck (1 trip detection logic).
- P2112The ECM signals the throttle actuator to open, but the actuator is stuck (1 trip detection logic).
- P2112The ECM signals the throttle actuator to open, but the actuator is stuck (1 trip detection logic).
- P2118Open in electronic throttle control system power source (+BM) circuit (1 trip detection logic)
- P2119The throttle valve opening angle continues to vary greatly from the target opening angle (1 trip detection...
- P2119The throttle valve opening angle continues to vary greatly from the target opening angle (1 trip detection...
- P2119The throttle valve opening angle continues to vary greatly from the target opening angle (1 trip detection...
- P2120VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip...
- P2121Either of following conditions 1 or 2 met for 0.5 seconds (1 trip detection logic): 1. Difference between VPA...
- P2121Either of following conditions 1 or 2 met for 0.5 seconds (1 trip detection logic): 1. Difference between VPA...
- P2121Either of following conditions 1 or 2 met for 0.5 seconds (1 trip detection logic): 1. Difference between VPA...
- P2122VPA 0.4 V or less for 0.5 seconds or more when accelerator pedal depressed (1 trip detection logic)
- P2123VPA 4.8 V or more for 2.0 seconds or more (1 trip detection logic)
- P2125VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip...
- P2127VPA2 1.2 V or less for 0.5 seconds or more when accelerator pedal depressed (1 trip detection logic)
- P2128Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic): (a) VPA2 4.8 V or more (b)...
- P2135Either of the following conditions is met (1 trip detection logic): (a) The difference between the output...
- P2138Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic): (a) Difference between VPA...
- P2195Conditions (a) and (b) continue for 40 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2195Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2195Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2196Conditions (a) and (b) continue for 2 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2196Conditions (a) and (b) continue for 2 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2196Conditions (a) and (b) continue for 40 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2197Conditions (a) and (b) continue for 40 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2197Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2197Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2198Conditions (a) and (b) continue for 2 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2198Conditions (a) and (b) continue for 2 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2198Conditions (a) and (b) continue for 40 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2237An open in the circuit between terminals A1A+ (A2A+) and A1A- (A2A-) of the air fuel ratio sensor while the...
- P2237An open in the circuit between terminals A1A+ (A2A+) and A1A- (A2A-) of the air fuel ratio sensor while the...
- P2238· Case 1: Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) Voltage at...
- P2238· Case 1: Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) Voltage at...
- P2239The A1A+ (A2A+) voltage is higher than 4.5 V (2 trip detection logic).
- P2239The A1A+ (A2A+) voltage is higher than 4.5 V (2 trip detection logic).
- P2240An open in the circuit between terminals A1A+ (A2A+) and A1A- (A2A-) of the air fuel ratio sensor while the...
- P2240An open in the circuit between terminals A1A+ (A2A+) and A1A- (A2A-) of the air fuel ratio sensor while the...
- P2241· Case 1: Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) Voltage at...
- P2241· Case 1: Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) Voltage at...
- P2242The A1A+ (A2A+) voltage is higher than 4.5 V (2 trip detection logic).
- P2242The A1A+ (A2A+) voltage is higher than 4.5 V (2 trip detection logic).
- P2252The A1A- (A2A-) voltage is 0.5 V or less (2 trip detection logic).
- P2252The A1A- (A2A-) voltage is 0.5 V or less (2 trip detection logic).
- P2253The A1A- (A2A-) voltage is higher than 4.5 V (2 trip detection logic).
- P2253The A1A- (A2A-) voltage is higher than 4.5 V (2 trip detection logic).
- P2255The A1A- (A2A-) voltage is 0.5 V or less (2 trip detection logic).
- P2255The A1A- (A2A-) voltage is 0.5 V or less (2 trip detection logic).
- P2256The A1A- (A2A-) voltage is higher than 4.5 V (2 trip detection logic).
- P2256The A1A- (A2A-) voltage is higher than 4.5 V (2 trip detection logic).
- P2610ECM internal malfunction (2 trip detection logic).
- P2A00Calculated value of the air fuel ratio sensor response rate deterioration level is less than the threshold (2...
- P2A00Calculated value of the air fuel ratio sensor response rate deterioration level is less than the threshold (2...
- P2A00Calculated value of the air fuel ratio sensor response rate deterioration level is less than the threshold (2...
- P2A03Calculated value of the air fuel ratio sensor response rate deterioration level is less than the threshold (2...
- P2A03Calculated value of the air fuel ratio sensor response rate deterioration level is less than the threshold (2...
- P2A03Calculated value of the air fuel ratio sensor response rate deterioration level is less than the threshold (2...
- U0101No communication from TCM continues (1 trip detection logic)
- U0101No communication from TCM continues (1 trip detection logic)
- U0129Following conditions are met for 2 seconds (1 trip detection logic): (a) Engine switch on (IG) (b) Battery...
- U0129Following conditions are met for 2 seconds (1 trip detection logic): (a) Engine switch on (IG) (b) Battery...
- U0129Following conditions are met for 2 seconds (1 trip detection logic): (a) Engine switch on (IG) (b) Battery...
- B2271LH-IG relay 1 actuation circuit or IG2 relay actuation circuit inside main body ECU is abnormal
- B2272LH-IG relay 1 actuation circuit inside main body ECU or other related circuit is malfunctioning
- B2273IG2 relay actuation circuit inside main body ECU or other related circuit is malfunctioning
- B2274ACC relay actuation circuit inside main body ECU or other related circuit is malfunctioning
- B2275Engine start request signal circuit inside main body ECU or other related circuit is malfunctioning
- B2275Engine start request signal circuit inside main body ECU or other related circuit is malfunctioning
- B2276ACCR output circuit inside main body ECU or other related circuit is malfunctioning
- B2276ACCR output circuit inside main body ECU or other related circuit is malfunctioning
- B2277Submersion circuit monitor inside main body ECU detects that vehicle is submerged in water
- B2278Communication is abnormal between main body ECU and engine switch or engine switch is defective
- B2281Communication or communication line is abnormal between main body ECU and shift lock control ECU
- B2282Following conditions are met: · Signals between main body ECU and combination meter are inconsistent ·...
- B2283When both conditions below are met: · Vehicle speed decreases significantly · Vehicle speed does not...
- B2284The brake signal circuit between the main body ECU and the stop light switch is malfunctioning and the CAN...
- B2285Cable and LIN information between main body ECU and steering lock ECU are inconsistent
- B2286Cable and CAN information between main body ECU and ECM are inconsistent
- B2286Cable and CAN information between main body ECU and ECM are inconsistent
- B2287Communication or communication line is abnormal between main body ECU and certification ECU
- B2288After turning engine switch from off to on (IG), steering wheel does not unlock for certain period of time...
- B2289Either of following conditions is met: · Communication or communication line is abnormal among main body ECU,...
- B2271LH-IG relay 1 actuation circuit or IG2 relay actuation circuit inside main body ECU is abnormal
- B2272LH-IG relay 1 actuation circuit inside main body ECU or other related circuit is malfunctioning
- B2273IG2 relay actuation circuit inside main body ECU or other related circuit is malfunctioning
- B2274ACC relay actuation circuit inside main body ECU or other related circuit is malfunctioning
- B2275Engine start request signal circuit inside main body ECU or other related circuit is malfunctioning
- B2275Engine start request signal circuit inside main body ECU or other related circuit is malfunctioning
- B2276ACCR output circuit inside main body ECU or other related circuit is malfunctioning
- B2276ACCR output circuit inside main body ECU or other related circuit is malfunctioning
- B2277Submersion circuit monitor inside main body ECU detects that vehicle is submerged in water
- B2278Communication is abnormal between main body ECU and engine switch or engine switch is defective
- B2281Communication or communication line is abnormal between main body ECU and shift lock control ECU
- B2282Following conditions are met: · Signals between main body ECU and combination meter are inconsistent ·...
- B2283When both conditions below are met: · Vehicle speed decreases significantly · Vehicle speed does not...
- B2284The brake signal circuit between the main body ECU and the stop light switch is malfunctioning and the CAN...
- B2284The brake signal circuit between the main body ECU and the stop light switch is malfunctioning and the CAN...
- B2285Cable and LIN information between main body ECU and steering lock ECU are inconsistent
- B2286Cable and CAN information between main body ECU and ECM are inconsistent
- B2286Cable and CAN information between main body ECU and ECM are inconsistent
- B2287Communication or communication line is abnormal between main body ECU and certification ECU
- B2288After turning ignition switch from off to on (IG), steering wheel does not unlock for certain period of time...
- B2289Either of following conditions is met: · Communication or communication line is abnormal among main body ECU,...
- B2271LH-IG relay 1 actuation circuit or IG2 relay actuation circuit inside main body ECU is abnormal
- B2272LH-IG relay 1 actuation circuit inside main body ECU or other related circuit is malfunctioning
- B2273IG2 relay actuation circuit inside main body ECU or other related circuit is malfunctioning
- B2274ACC relay actuation circuit inside main body ECU or other related circuit is malfunctioning
- B2275STSW output circuit (engine starting request signal circuit) inside main body ECU or other related circuit is...
- B2276ACCR output circuit inside main body ECU or other related circuit is malfunctioning
- B2277Submersion circuit monitor inside main body ECU detects that vehicle is submerged in water
- B2278Communication is abnormal between the main body ECU and engine switch or the engine switch is defective
- B2278Communication is abnormal between the main body ECU and engine switch or the engine switch is defective
- B2281Cable information and CAN information between main body ECU and shift lock control ECU are inconsistent
- B2282Cable information and CAN information between the main body ECU and the combination meter are inconsistent
- B2282Cable information and CAN information between the main body ECU and the combination meter are inconsistent
- B2283When either of conditions below are met: · Over-deceleration in vehicle speed · Vehicle speed and engine...
- B2283When either of conditions below are met: · Over-deceleration in vehicle speed · Vehicle speed and engine...
- B2284The brake signal circuit between the main body ECU and the stop light switch is malfunctioning and the CAN...
- B2284The brake signal circuit between the main body ECU and the stop light switch is malfunctioning and the CAN...
- B2285Cable and LIN information between the main body ECU and the steering lock ECU are inconsistent
- B2286Serial communication signals and CAN communication signals in the circuit between the main body ECU and ECM...
- B2286Serial communication signals and CAN communication signals in the circuit between the main body ECU and ECM...
- B2287Communication or communication line is abnormal between the main body ECU and the certification ECU
- B2288After turning engine switch from off to on (IG), the steering wheel does not unlock for a certain period of...
- B2289Either condition below is met: · LIN communication is abnormal between the main body ECU and the...
- B2271LH-IG relay 1 actuation circuit or IG2 relay actuation circuit inside main body ECU is abnormal
- B2272LH-IG relay 1 actuation circuit inside main body ECU or other related circuit is malfunctioning
- B2273IG2 relay actuation circuit inside main body ECU or other related circuit is malfunctioning
- B2274ACC relay actuation circuit inside main body ECU or other related circuit is malfunctioning
- B2275STSW output circuit (engine starting request signal circuit) inside main body ECU or other related circuit is...
- B2276ACCR output circuit inside main body ECU or other related circuit is malfunctioning
- B2277Submersion circuit monitor inside main body ECU detects that vehicle is submerged in water
- B2278Communication is abnormal between the main body ECU and engine switch or the engine switch is defective
- B2278Communication is abnormal between the main body ECU and engine switch or the engine switch is defective
- B2281Cable information and CAN information between main body ECU and shift lock control ECU are inconsistent
- B2282Cable information and CAN information between the main body ECU and the combination meter are inconsistent
- B2282Cable information and CAN information between the main body ECU and the combination meter are inconsistent
- B2283When either of conditions below are met: · Over-deceleration in vehicle speed · Vehicle speed and engine...
- B2283When either of conditions below are met: · Over-deceleration in vehicle speed · Vehicle speed and engine...
- B2284The brake signal circuit between the main body ECU and the stop light switch is malfunctioning and the CAN...
- B2284The brake signal circuit between the main body ECU and the stop light switch is malfunctioning and the CAN...
- B2285Cable and LIN information between the main body ECU and the steering lock ECU are inconsistent
- B2286Serial communication signals and CAN communication signals in the circuit between the main body ECU and ECM...
- B2286Serial communication signals and CAN communication signals in the circuit between the main body ECU and ECM...
- B2287Communication or communication line is abnormal between the main body ECU and the certification ECU
- B2288After turning engine switch from off to on (IG), the steering wheel does not unlock for a certain period of...
- B2289Either condition below is met: · LIN communication is abnormal between the main body ECU and the...
- P0500The vehicle speed signal from the vehicle speed sensor is cut for 0.14 sec. or more while cruise control is...
- P0500The vehicle speed signal from the vehicle speed sensor is cut for 0.14 sec. or more while cruise control is...
- P0503Momentary interruption and noise are detected when a rapid change of vehicle speed occurs while cruise...
- P0503Momentary interruption and noise are detected when a rapid change of vehicle speed occurs while cruise...
- P0571When both conditions below are met: · Voltage of terminal STP is less than 1 V for 0.5 seconds or more ·...
- P0571When both conditions below are met: · Voltage of terminal STP is less than 1 V for 0.5 seconds or more ·...
- P0575When either of following conditions is met: · Cruise control input signal abnormal · Stop light switch input...
- P0607When either of following conditions is met: · Cruise control input signal abnormal · Stop light switch input...
- P0705When one of the following conditions is met: (A) Any 2 or more of the following signals are ON simultaneously...
- P0705When one of the following conditions is met: (A) Any 2 or more of the following signals are ON simultaneously...
- P0705When one of the following conditions is met: (A) Any 2 or more of the following signals are ON simultaneously...
- P0710ATF temperature sensor resistance changes from (a) to (b) or from (b) to (a) in less than 0.5 sec., and P0712...
- P0711Either condition is met (2 trip detection logic): · Certain monitor enabling conditions are met and the ATF...
- P0712ATF temperature sensor resistance is less than 79 Ω for 0.5 sec. or more (1 trip detection logic)
- P071315 minutes or more after the engine start, ATF temperature sensor resistance is more than 156 kΩ for 0.5 sec....
- P0717ECM detects conditions (a), (b) and (c) continuously for 5 sec. or more (1 trip detection logic): (a) Vehicle...
- P0724Stop light switch remains ON even when vehicle is driven in GO (30 km/h (18.63 mph) or more) and STOP (less...
- P0724Stop light switch remains ON even when vehicle is driven in GO (30 km/h (18.63 mph) or more) and STOP (less...
- P0741Lock-up does not occur when driving in lock-up range Lock-up remains ON in lock-up OFF range (2 trip...
- P0746Gear required by the ECM does not match the actual gear when driving (2 trip detection logic)
- P0748Duty cycle to shift solenoid valve SL1 is 100% (1 trip detection logic)
- P0766Gear required by the ECM does not match the actual gear when driving (2 trip detection logic)
- P0776Gear required by the ECM does not match the actual gear when driving (2 trip detection logic)
- P0778Duty cycle to shift solenoid valve SL2 is 100% (1 trip detection logic)
- P0793ECM detects conditions (a), (b) and (c) continuously for 5 sec. or more (1 trip detection logic): (a) Vehicle...
- P0982ECM detects short in solenoid valve S4 circuit 2 times when solenoid valve S4 is operated (1 trip detection...
- P0983ECM detects open in solenoid valve S4 circuit 2 times when solenoid valve S4 is not operated (1 trip...
- P2716Either condition (a) or (b) below is detected for 1 sec. or more (1 trip detection logic): (a) SLT -...
- P2769ECM detects short in shift solenoid valve DSL circuit when shift solenoid valve DSL is operated (2 trip...
- P2770ECM detects open in shift solenoid valve DSL circuit when shift solenoid valve DSL is not operated (2 trip...
- P0500When the ECT sensor is normal and the counter gear speed is 300 rpm or more, the vehicle speed signal is not...
- P0560Open in TCM back-up power source circuit. DTC is detected for 3 sec. or more (1-trip detection logic).
- P0617When conditions (a), (b) and (c) are met, positive (+B) battery voltage 10.5 V or more is applied to the TCM...
- P0617When conditions (a), (b) and (c) are met, positive (+B) battery voltage 10.5 V or more is applied to the TCM...
- P0705(a) Any 2 or more signals of the following are ON simultaneously (2-trip detection logic) · NSW input signal...
- P0710(a) and (b) are detected momentarily (within 0.5 sec.) when neither P0712 nor P0713 is detected (1-trip...
- P0711Either condition is met (2-trip detection logic) · Certain monitor enabling conditions are met and the ATF...
- P0711Either condition is met (2-trip detection logic) · Certain monitor enabling conditions are met and the ATF...
- P0712ATF temperature sensor resistance is less than 79 Ω for 0.5 sec. or more (1-trip detection logic).
- P0713ATF temperature sensor resistance is more than 156 kΩ when 15 minutes or more have elapsed after the engine...
- P0715When the speed sensor input voltage is either more than 1.9 V or less than 0.1 V for 4.5 seconds or more.
- P0717ECM detects conditions (a), (b) and (c) continuously for 5 sec. or more (1-trip detection logic): (a) Vehicle...
- P0724The stop light switch remains ON even when the vehicle is driven in a STOP (less than 3 km/h (2 mph)) and GO...
- P0724The stop light switch remains ON even when the vehicle is driven in a STOP (less than 3 km/h (2 mph)) and GO...
- P0741When both of the following are detected (2-trip detection logic): · Lock-up does not occur when requested. ·...
- P0746The engine revs freely when 1st, 2nd, 3rd, or 4th gear is requested. (2-trip detection logic) When either of...
- P0748The TCM checks for an open or short in the shift solenoid valve SL1 circuit while driving and shifting...
- P0776The engine revs freely when 4th, 5th, or 6th gear is requested. (2-trip detection logic) When any of the...
- P0778The TCM checks for an open or short in the shift solenoid valve SL2 circuit while driving and shifting gears....
- P0791When the speed sensor input voltage is either more than 1.9 V or less than 0.1 V for 2 seconds or more.
- P0793When the vehicle speed is 15.5 mph (25 km/h) or higher, the counter gear speed is less than 300 rpm for 2...
- P0796The engine revs freely when 2nd or 6th gear is requested. (2-trip detection logic) When the following is...
- P0798The TCM checks for an open or short in the shift solenoid valve SL3 circuit while driving and shifting gears....
- P0872ATF pressure switch No. 1 OFF is detected twice when any of the gears from 1st to 4th engages normally.
- P0873ATF pressure switch No. 1 ON is detected twice when 5th or 6th gear engages normally.
- P0877ATF pressure switch No. 2 OFF is detected twice when any of the gears from 4th to 6th engages normally.
- P0878ATF pressure switch No. 2 ON is detected twice when any of the gears from 1st to 3rd engages normally.
- P0989Transmission fluid pressure switch No. 3 is OFF when lock-up occurs in response to a lock-up request (2-trip...
- P0990When both of the following are detected (2-trip detection logic): · Transmission fluid pressure switch No. 3...
- P2714The TCM detects a malfunction in the shift solenoid valve SLT (ON side) according to the difference in the...
- P2716Open or short is detected in shift solenoid valve SLT circuit for 1 second or more while driving (1-trip...
- P2757When both of the following are detected (2-trip detection logic): · Lock-up does not occur when requested. ·...
- P2759Open or short is detected in shift solenoid valve SLU circuit for 1 second or more while driving (1-trip...
- P2769TCM detects a short in the shift solenoid valve SL circuit when the shift solenoid valve SL is operated...
- P2770TCM detects an open in the shift solenoid valve SL circuit when the shift solenoid valve SL is not operated...
- P2808The engine revs freely when 3rd or 5th gear is requested. (2-trip detection logic) When any of the following...
- P2810The TCM checks for an open or short in the shift solenoid valve SL4 circuit while driving and shifting gears....
- U0100Following conditions are met for 1.25 seconds (1-trip detection logic): (a) Ignition switch on (IG) (b)...
- U0100Following conditions are met for 1.25 seconds (1-trip detection logic): (a) Ignition switch on (IG) (b)...
- P07051. Engine switch on (IG) and battery voltage is 10.5 V or more 2. Any 2 or more of the following signals are...
- P07051. Engine switch on (IG) and battery voltage is 10.5 V or more 2. Any 2 or more of the following signals are...
- P07051. Engine switch on (IG) and battery voltage is 10.5 V or more 2. Any 2 or more of the following signals are...
- P07111. The intake air and engine coolant temperatures are more than -10°C (14°F) at engine start, and the vehicle...
- P07111. The intake air and engine coolant temperatures are more than -10°C (14°F) at engine start, and the vehicle...
- P07111. The intake air and engine coolant temperatures are more than -10°C (14°F) at engine start, and the vehicle...
- P07121. - 2. There is a short circuit in the CVT fluid temperature sensor circuit. 3. 0.5 seconds 4. 1 trip...
- P07121. - 2. There is a short circuit in the CVT fluid temperature sensor circuit. 3. 0.5 seconds 4. 1 trip...
- P07121. - 2. There is a short circuit in the CVT fluid temperature sensor circuit. 3. 0.5 seconds 4. 1 trip...
- P07131. 15 minutes or more after starting the engine. 2. There is an open circuit in the CVT fluid temperature...
- P07131. 15 minutes or more after starting the engine. 2. There is an open circuit in the CVT fluid temperature...
- P07131. 15 minutes or more after starting the engine. 2. There is an open circuit in the CVT fluid temperature...
- P07151. A transmission revolution sensor (NT) signal malfunction is not detected. 2. The transmission revolution...
- P07171. The vehicle is driven with the shift lever in D, the output shaft speed is 300 rpm or more, and no error...
- P07171. The vehicle is driven with the shift lever in D, the output shaft speed is 300 rpm or more, and no error...
- P07171. The vehicle is driven with the shift lever in D, the output shaft speed is 300 rpm or more, and no error...
- P07201. A transmission revolution (NOUT) signal malfunction is not detected. 2. The transmission revolution sensor...
- P07221. The vehicle is driven with the shift lever in D, the output shaft speed is 300 rpm or more, and no error...
- P07221. The vehicle is driven with the shift lever in D, the output shaft speed is 300 rpm or more, and no error...
- P07221. The vehicle is driven with the shift lever in D, the output shaft speed is 300 rpm or more, and no error...
- P07411. The engine is warmed up, and the vehicle is driven at a speed of 10 km/h (6.0 mph) or more with the shift...
- P07411. The engine is warmed up, and the vehicle is driven at a speed of 10 km/h (6.0 mph) or more with the shift...
- P07411. The engine is warmed up, and the vehicle is driven at a speed of 10 km/h (6.0 mph) or more with the shift...
- P07461. The engine is warmed up, and with the shift lever in D, the vehicle is accelerating. 2. The actual gear...
- P07461. The engine is warmed up, and with the shift lever in D, the vehicle is accelerating. 2. The actual gear...
- P07461. The engine is warmed up, and with the shift lever in D, the vehicle is accelerating. 2. The actual gear...
- P07761. The engine is warmed up, and with the shift lever in D, the vehicle is decelerating or stopped. 2. The...
- P07761. The engine is warmed up, and with the shift lever in D, the vehicle is decelerating or stopped. 2. The...
- P07761. The engine is warmed up, and with the shift lever in D, the vehicle is decelerating or stopped. 2. The...
- P08401. 2 seconds or more have elapsed after the engine is started. 2. There is an open or short circuit in the...
- P08401. 2 seconds or more have elapsed after the engine is started. 2. There is an open or short circuit in the...
- P08411. The requested oil pressure value is 0.5 MPa or less. 2. The oil pressure sensor output value is 3.0 MPa or...
- P08411. The requested oil pressure value is 0.5 MPa or less. 2. The oil pressure sensor output value is 3.0 MPa or...
- P08411. The requested oil pressure value is 0.5 MPa or less. 2. The oil pressure sensor output value is 3.0 MPa or...
- P08421. 2 seconds or more have elapsed after the engine is started. 2. There is a short circuit in the oil...
- P08421. 2 seconds or more have elapsed after the engine is started. 2. There is a short circuit in the oil...
- P08431. 2 seconds or more have elapsed after the engine is started. 2. There is an open circuit in the oil...
- P08431. 2 seconds or more have elapsed after the engine is started. 2. There is an open circuit in the oil...
- P09621. The vehicle is driven so that gear ratio changes occur. 2. There is a short circuit in the shift solenoid...
- P09621. The vehicle is driven so that gear ratio changes occur. 2. There is a short circuit in the shift solenoid...
- P09631. The vehicle is driven so that gear ratio changes occur. 2. There is an open circuit in the shift solenoid...
- P09631. The vehicle is driven so that gear ratio changes occur. 2. There is an open circuit in the shift solenoid...
- P09661. The vehicle is driven so that gear ratio changes occur. 2. There is a short circuit in the shift solenoid...
- P09661. The vehicle is driven so that gear ratio changes occur. 2. There is a short circuit in the shift solenoid...
- P09671. The vehicle is driven so that gear ratio changes occur. 2. There is an open circuit in the shift solenoid...
- P09671. The vehicle is driven so that gear ratio changes occur. 2. There is an open circuit in the shift solenoid...
- P15851. The engine switch is on (IG). 2. The output value of the deceleration sensor remains at -1.5 G or less, or...
- P15851. The engine switch is on (IG). 2. The output value of the yaw rate sensor remains at -1.5 G or less, or 1.5...
- P15851. The engine switch is on (IG). 2. The output value of the yaw rate sensor remains at -1.5 G or less, or 1.5...
- P15861. The engine switch is on (IG). 2. With a vehicle speed of 30 km/h (18 mph) or more, the difference between...
- P15861. The engine switch is on (IG). 2. With a vehicle speed of 30 km/h (18 mph) or more, the difference between...
- P15861. The engine switch is on (IG). 2. With a vehicle speed of 30 km/h (18 mph) or more, the difference between...
- P15891. The vehicle speed is 2 km/h (1.2 mph) or more. 2. Deceleration sensor 0 point calibration has not been...
- P15891. The vehicle speed is 2 km/h (1.2 mph) or more. 2. Deceleration sensor 0 point calibration has not been...
- P15891. The vehicle speed is 2 km/h (1.2 mph) or more. 2. Deceleration sensor 0 point calibration has not been...
- P17501. - 2. The ECM receives an error signal from the brake actuator assembly (skid control ECU). 3. 3 seconds 4....
- P17501. - 2. The ECM receives an error signal from the brake actuator assembly (skid control ECU). 3. 3 seconds 4....
- P17501. - 2. The ECM receives an error signal from the brake actuator assembly (skid control ECU). 3. 3 seconds 4....
- P27571. The engine is warmed up, and the vehicle is driven at a speed of 10 km/h (6.0 mph) or more with the shift...
- P27571. The engine is warmed up, and the vehicle is driven at a speed of 10 km/h (6.0 mph) or more with the shift...
- P27571. The engine is warmed up, and the vehicle is driven at a speed of 10 km/h (6.0 mph) or more with the shift...
- P27631. The vehicle is being driven. 2. There is an open circuit in the shift solenoid valve DSU circuit. 3....
- P27631. The vehicle is being driven. 2. There is an open circuit in the shift solenoid valve DSU circuit. 3....
- P27641. The vehicle is being driven. 2. There is a short circuit in the shift solenoid valve DSU circuit. 3....
- P27641. The vehicle is being driven. 2. There is a short circuit in the shift solenoid valve DSU circuit. 3....
- P27671. The vehicle is driven with the shift lever in D, the output shaft speed is 300 rpm or more and the vehicle...
- P27671. The vehicle is driven with the shift lever in D, the output shaft speed is 300 rpm or more and the vehicle...
- P27691. Lock-up is operating. 2. There is a short circuit in the shift solenoid valve SL circuit. 3. Detected 2...
- P27691. Lock-up is operating. 2. There is a short circuit in the shift solenoid valve SL circuit. 3. Detected 2...
- P27701. Lock-up is operating. 2. There is an open circuit in the shift solenoid valve SL circuit. 3. Detected 2...
- P27701. Lock-up is operating. 2. There is an open circuit in the shift solenoid valve SL circuit. 3. Detected 2...
- P28291. The requested oil pressure value is 0.5 MPa or less. 2. The oil pressure sensor output value is 3.0 MPa or...
- P28291. The requested oil pressure value is 0.5 MPa or less. 2. The oil pressure sensor output value is 3.0 MPa or...
- P28291. The requested oil pressure value is 0.5 MPa or less. 2. The oil pressure sensor output value is 3.0 MPa or...
- P282B1. The vehicle is being driven. 2. There is an open or short circuit in the shift solenoid valve SLS circuit....
- P282B1. The vehicle is being driven. 2. There is an open or short circuit in the shift solenoid valve SLS circuit....
- U01291. The engine switch is on (IG). 2. There is no communication between the ECM and skid control ECU. 3. 2.4...
- U01291. The engine switch is on (IG). 2. There is no communication between the ECM and skid control ECU. 3. 2.4...
- U01291. The engine switch is on (IG). 2. There is no communication between the ECM and skid control ECU. 3. 2.4...
- C2111/11 Tire pressure warning valve and transmitters stop transmitting signals
- C2112/12 Tire pressure warning valve and transmitters stop transmitting signals
- C2113/13 Tire pressure warning valve and transmitters stop transmitting signals
- C2114/14 Tire pressure warning valve and transmitters stop transmitting signals
- C2115/15 Tire pressure warning valve and transmitters stop transmitting signals
- C2121/21 Following condition (a) or (b) is met: (a) When all conditions below are met: · Tire pressure warning valve...
- C2122/22 Following condition (a) or (b) is met: (a) When all conditions below are met: · Tire pressure warning valve...
- C2123/23 Following condition (a) or (b) is met: (a) When all conditions below are met: · Tire pressure warning valve...
- C2124/24 Following condition (a) or (b) is met: (a) When all conditions below are met: · Tire pressure warning valve...
- C2125/25 Following condition (a) or (b) is met: (a) When all conditions below are met: · Tire pressure warning valve...
- C2126/26 After transmitter ID registration is completed, ECU does not receive radio waves from transmitters whose IDs...
- C2141/41 If an "ERROR" signal is received 3 times consecutively, the tire pressure warning valve and transmitter will...
- C2142/42 If an "ERROR" signal is received 3 times consecutively, the tire pressure warning valve and transmitter will...
- C2143/43 If an "ERROR" signal is received 3 times consecutively, the tire pressure warning valve and transmitter will...
- C2144/44 If an "ERROR" signal is received 3 times consecutively, the tire pressure warning valve and transmitter will...
- C2145/45 If an "ERROR" signal is received 3 times consecutively, the tire pressure warning valve and transmitter will...
- C2171/71 Transmitter ID code is not registered. (When an ID code is unregistered for 3 minutes or more)
- C2174/74 Vehicle speed signal malfunction
- C2176/76 Malfunction in the tire pressure warning ECU and receiver internal circuit
- C2177/77 All conditions below are met: · During initialization · Tire pressure warning valve and transmitter is not in...
- C2181/81 Test mode procedure is performed.
- C2182/82 Test mode procedure is performed.
- C2183/83 Test mode procedure is performed.
- C2184/84 Test mode procedure is performed.
- C2185/85 Test mode procedure is performed.
- C2191/91 Test mode procedure is performed
- C2198/98 Test mode procedure is performed.
- C0200/31 When one of following conditions is met: 1. Non-plausible high frequent signal, high wheel acceleration or...
- C0200/31 When one of following conditions is met: 1. Non-plausible high frequent signal, high wheel acceleration or...
- C0205/32 When one of following conditions is met: 1. Non-plausible high frequent signal, high wheel acceleration or...
- C0205/32 When one of following conditions is met: 1. Non-plausible high frequent signal, high wheel acceleration or...
- C0210/33 When one of following conditions is met: · Non-plausible high frequent signal, high wheel acceleration or...
- C0210/33 When one of following conditions is met: · Non-plausible high frequent signal, high wheel acceleration or...
- C0215/34 When one of following conditions is met: · Non-plausible high frequent signal, high wheel acceleration or...
- C0215/34 When one of following conditions is met: · Non-plausible high frequent signal, high wheel acceleration or...
- C0226/21 Solenoid valve signal does not match to the check result.
- C0236/22 Solenoid valve signal does not match to the check result.
- C0246/23 Solenoid valve signal does not match to the check result.
- C0256/24 Solenoid valve signal does not match to the check result.
- C0273/13 When either condition below is met: 1. Pump motor voltage is 2.0 V or more for 1 sec. or more at motor relay...
- C0278/11 When either condition below is met: 1. Internal circuit malfunction in ECU. 2. Valve relay voltage is 0.8 x...
- C1237/37 When any of following (1 to 3) detected: 1. Discrepancy among four wheel speed sensor output. 2. Abnormal...
- C1241/41 With vehicle speed to about 6 km/h (4 mph), battery voltage is less than 9.4 V at the time of non-operation...
- C1243/43 While the vehicle is being driven and the brake pedal is not depressed, the deceleration sensor value remains...
- C1244/44 Either of the following is detected: 1. Deceleration sensor output voltage is 4.7 V or more, or 0.3 V or less...
- C1245/45 Either of the following is detected: 1. When the vehicle speed is 30 km/h (19 mph) or more, the difference...
- C1249/49 When IG1 terminal voltage is 9.5 to 17.2 V, open circuit of stop light switch continues for 0.5 seconds or...
- C1271/71 Detected only during test mode.
- C1271/71 Detected only during test mode.
- C1272/72 Detected only during test mode.
- C1272/72 Detected only during test mode.
- C1273/73 Detected only during test mode.
- C1273/73 Detected only during test mode.
- C1274/74 Detected only during test mode.
- C1274/74 Detected only during test mode.
- C1275/75 Detected only during test mode.
- C1275/75 Detected only during test mode.
- C1276/76 Detected only during test mode.
- C1276/76 Detected only during test mode.
- C1277/77 Detected only during test mode.
- C1277/77 Detected only during test mode.
- C1278/78 Detected only during test mode.
- C1278/78 Detected only during test mode.
- C1300/62 Skid control ECU malfunction
- C1330/35 Abnormality in the resistance value of each speed sensor is detected.
- C1330/35 Abnormality in the resistance value of each speed sensor is detected.
- C1331/36 Abnormality in the resistance value of each speed sensor is detected.
- C1331/36 Abnormality in the resistance value of each speed sensor is detected.
- C1332/38 Abnormality in the resistance value of each speed sensor is detected.
- C1332/38 Abnormality in the resistance value of each speed sensor is detected.
- C1333/39 Abnormality in the resistance value of each speed sensor is detected.
- C1333/39 Abnormality in the resistance value of each speed sensor is detected.
- C0200/31 When one of following conditions is met: 1. Vehicle speed is more than 40 km/h (25 mph) and pulses are not...
- C0205/32 When one of following conditions is met: 1. Vehicle speed is more than 40 km/h (25 mph) and pulses are not...
- C0210/33 When one of following conditions is met: 1. Vehicle speed is more than 40 km/h (25 mph) and pulses are not...
- C0215/34 When one of following conditions is met: 1. Vehicle speed is more than 40 km/h (25 mph) and pulses are not...
- C0226/21 Solenoid valve signal does not match the check result.
- C0236/22 Solenoid valve signal does not match the check result.
- C0246/23 Solenoid valve signal does not match the check result.
- C0256/24 Solenoid valve signal does not match the check result.
- C0273/13 When either condition below is met: 1. When the motor relay is actuated, voltage is not supplied to the pump...
- C0278/11 When either condition below is met: 1. 3 or more solenoid valves are determined to be fault and voltage...
- C0365/28 Sensor malfunction signal received from lateral deceleration sensor.
- C1201Engine Control System Malfunction
- C1201Engine Control System Malfunction
- C1201/51 Engine control system malfunction signal continues for 5 seconds.
- C1224NE Signal
- C1224NE Signal
- C1225SM Solenoid Circuit
- C1225SM Solenoid Circuit
- C1225/25 Open or short in SRM or SRC circuit.
- C1226SA2 Solenoid Circuit
- C1226SA2 Solenoid Circuit
- C1226/26 Open or short in SRM or SRC circuit.
- C1227SA3 Solenoid Circuit
- C1227SA3 Solenoid Circuit
- C1227/27 Open or short in SRM or SRC circuit.
- C1228STR Solenoid Circuit
- C1228STR Solenoid Circuit
- C1228/28 Open or short in SRM or SRC circuit.
- C1231/31 When IG1 terminal voltage 9.5 V or more, steering angle sensor malfunction signal received.
- C1234Yaw Rate Sensor
- C1234Yaw Rate Sensor
- C1234/34 Sensor malfunction signal received from yaw rate sensor.
- C1237Speed Sensor Rotor Faulty
- C1237Speed Sensor Rotor Faulty
- C1237/37 When any of following (1 to 3) detected: 1. Discrepancy among four wheel speed sensor output. 2. Abnormal...
- C1241Low Power Supply Voltage Malfunction
- C1241Low Power Supply Voltage Malfunction
- C1241/41 When one of following conditions is met: 1. Battery voltage is 17.4 V or more. 2. Battery voltage is 9.8 V or...
- C1245/32 Any of the following is detected: 1. Longitudinal acceleration difference between sensor signal and reference...
- C1246Master Cylinder Pressure Sensor Malfunction
- C1246Master Cylinder Pressure Sensor Malfunction
- C1246/46 When one of following conditions is met: · The voltage of the sensor signal is out of range (less than 0.3 V,...
- C1249Open in Stop Light Switch Circuit
- C1249Open in Stop Light Switch Circuit
- C1249/49 The vehicle speed is 10 km/h (6 mph) or more, the accelerator pedal is depressed, the master cylinder...
- C1267/67 When one of following conditions is met: 1. An open or short in the brake pedal load sensing switch continues...
- C1271Low Output Signal of Front Speed Sensor RH (Test Mode DTC)
- C1271Low Output Signal of Front Speed Sensor RH (Test Mode DTC)
- C1271/71 Detected only during test mode.
- C1272Low Output Signal of Front Speed Sensor LH (Test Mode DTC)
- C1272Low Output Signal of Front Speed Sensor LH (Test Mode DTC)
- C1272/72 Detected only during test mode.
- C1273Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)
- C1273Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)
- C1273/73 Detected only during test mode.
- C1274Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)
- C1274Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)
- C1274/74 Detected only during test mode.
- C1275Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC)
- C1275Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC)
- C1275/75 Detected only during test mode.
- C1276Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC)
- C1276Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC)
- C1276/76 Detected only during test mode.
- C1277Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)
- C1277Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)
- C1277/77 Detected only during test mode.
- C1278Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)
- C1278Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)
- C1278/78 Detected only during test mode.
- C1281Master Cylinder Pressure Sensor Output Malfunction (Test Mode DTC)
- C1281Master Cylinder Pressure Sensor Output Malfunction (Test Mode DTC)
- C1281/81 Detected only during test mode.
- C1288Error in Matching of ECUs
- C1288Error in Matching of ECUs
- C1288/88 Engine variation information stored in skid control ECU and ECM do not match
- C1300Skid Control ECU Malfunction
- C1300Skid Control ECU Malfunction
- C1300/62 Skid control ECU malfunction
- C1330Open in Front Speed Sensor RH
- C1330Open in Front Speed Sensor RH
- C1330/35 Abnormality in the resistance value of each speed sensor is detected.
- C1331Open in Front Speed Sensor LH
- C1331Open in Front Speed Sensor LH
- C1331/36 Abnormality in the resistance value of each speed sensor is detected.
- C1332Open in Rear Speed Sensor RH
- C1332Open in Rear Speed Sensor RH
- C1332/38 Abnormality in the resistance value of each speed sensor is detected.
- C1333Open in Rear Speed Sensor LH
- C1333Open in Rear Speed Sensor LH
- C1333/39 Abnormality in the resistance value of each speed sensor is detected.
- C1336Zero Point Calibration of Acceleration Sensor Undone
- C1336Zero Point Calibration of Acceleration Sensor Undone
- C1380/64 Either of the following is detected: 1. When the voltage at the IG1 terminal is between 10 and 14 V and the...
- C1381Acceleration Sensor Power Supply Voltage Malfunction
- C1381Acceleration Sensor Power Supply Voltage Malfunction
- C1417High Power Supply Voltage Malfunction
- C1417High Power Supply Voltage Malfunction
- C1419Acceleration Sensor Internal Circuit
- C1419Acceleration Sensor Internal Circuit
- C1420Acceleration Sensor Malfunction
- C1420Acceleration Sensor Malfunction
- C1425Open in Stop Light Switch Circuit
- C1425Open in Stop Light Switch Circuit
- C1425/49 An open in the stop light switch input line continues for 3 seconds or more.
- C1426Stop Light Switch OFF Stuck Malfunction
- C1426Stop Light Switch OFF Stuck Malfunction
- C1426/49 Either of the following is detected: 1. With the stop light switch off, the stop light switch is judged to be...
- C1428Motor Circuit Malfunction
- C1428Motor Circuit Malfunction
- C1429Open or Short in Brake Pedal Load Sensing Switch
- C1429Open or Short in Brake Pedal Load Sensing Switch
- C1430Brake Pedal Load Sensing Switch OFF Stuck Malfunction
- C1430Brake Pedal Load Sensing Switch OFF Stuck Malfunction
- C1431Brake Pedal Load Sensing Switch ON Stuck Malfunction
- C1431Brake Pedal Load Sensing Switch ON Stuck Malfunction
- C1432Steering Angle Sensor Power Source Voltage Malfunction
- C1432Steering Angle Sensor Power Source Voltage Malfunction
- C1433Steering Angle Sensor Internal Circuit
- C1433Steering Angle Sensor Internal Circuit
- C1434Steering Angle Sensor Output Malfunction
- C1434Steering Angle Sensor Output Malfunction
- C1435Yaw Rate Sensor Internal Circuit
- C1435Yaw Rate Sensor Internal Circuit
- C1436Yaw Rate Sensor Malfunction
- C1436Yaw Rate Sensor Malfunction
- C1439Steering Angle Sensor Initialization Incomplete
- C1439Steering Angle Sensor Initialization Incomplete
- C1439/31 After the steering angle sensor zero point calibration is cleared due to, for example, fluctuations in the...
- C1441Performance Decline of Brake Function
- C1441Performance Decline of Brake Function
- C1441When the brake pedal load sensing switch and master cylinder pressure sensor are functioning normally and the...
- C1445Vehicle Driven with Steering Angle Sensor not Initialized
- C1445Vehicle Driven with Steering Angle Sensor not Initialized
- C1445/31 Steering angle sensor zero point calibration cannot be obtained when the vehicle is driven without a record...
- C1448/98 When the vehicle speed is 20 km/h (12 mph) or more, an invalid data signal is received from the yaw rate...
- C1464Front Speed Sensor RH
- C1464Front Speed Sensor RH
- C1465Front Speed Sensor LH
- C1465Front Speed Sensor LH
- C1466Rear Speed Sensor RH
- C1466Rear Speed Sensor RH
- C1467Rear Speed Sensor LH
- C1467Rear Speed Sensor LH
- C1468SFR Solenoid Circuit
- C1468SFR Solenoid Circuit
- C1469SFL Solenoid Circuit
- C1469SFL Solenoid Circuit
- C146ASRR Solenoid Circuit
- C146ASRR Solenoid Circuit
- C146BSRL Solenoid Circuit
- C146BSRL Solenoid Circuit
- C146COpen in ABS Motor Relay Circuit
- C146COpen in ABS Motor Relay Circuit
- C146EOpen in ABS Solenoid Relay Circuit
- C146EOpen in ABS Solenoid Relay Circuit
- C1472Acceleration Sensor
- C1472Acceleration Sensor
- C1474Forward and Rearward G Sensor
- C1474Forward and Rearward G Sensor
- U0073Control Module Communication Bus OFF
- U0073Control Module Communication Bus OFF
- U0073/94 When one of following conditions is met: 1. With the IG1 terminal voltage 10 V or more, after the output of...
- U0100Lost Communication with ECM / PCM
- U0100Lost Communication with ECM / PCM
- U0100/65 When either condition below is met: 1. With the IG1 terminal voltage 10 V or more and the vehicle speed 9 mph...
- U0123Lost Communication with Yaw Rate Sensor Module
- U0123Lost Communication with Yaw Rate Sensor Module
- U0123/62 When either condition below is met: 1. With the IG1 terminal voltage 10 V or more, data from the deceleration...
- U0126Lost Communication with Steering Angle Sensor Module
- U0126Lost Communication with Steering Angle Sensor Module
- U0126/63 When either of following conditions detected: 1. When IG1 terminal voltage 10 V or more, data from steering...
- B2781When either condition below is met: · Steering lock motor drive power circuit malfunction · Lock or Unlock...
- B2782IGE power supply circuit malfunction
- B2785LIN communication from certification ECU stops for certain amount of time · Open or short in wire harness...
- B2786Certification ECU does not receive LIN communication from steering lock ECU for 10 seconds
- B2788Open or short in IG2 signal circuit
- C1511Torque sensor malfunction
- C1511Torque sensor malfunction
- C1512C1512
- C1512C1512
- C1513C1513
- C1513C1513
- C1514C1514
- C1514C1514
- C1515This DTC is detected when torque sensor zero point calibration has not been performed.
- C1515This DTC is detected when torque sensor zero point calibration has not been performed.
- C1516Torque sensor zero point calibration is incomplete due to the steering wheel being touched during calibration.
- C1516Torque sensor zero point calibration is incomplete due to the steering wheel being touched during calibration.
- C1517C1517
- C1517C1517
- C1521Motor overcurrent
- C1521Motor overcurrent
- C1522Short (or open) in motor circuit or abnormal voltage or current in motor circuit
- C1522Short (or open) in motor circuit or abnormal voltage or current in motor circuit
- C1523Motor current sensor malfunction
- C1523Motor current sensor malfunction
- C1524Excessively large current deviation
- C1524Excessively large current deviation
- C1525This DTC is detected when rotation angle sensor value initialization has not been performed.
- C1525This DTC is detected when rotation angle sensor value initialization has not been performed.
- C1526Rotation angle sensor value initialization is incomplete due to the steering wheel being touched during...
- C1526Rotation angle sensor value initialization is incomplete due to the steering wheel being touched during...
- C1528Motor rotation angle sensor malfunction
- C1528Motor rotation angle sensor malfunction
- C1531ECU internal malfunction (CPU malfunction)
- C1531ECU internal malfunction (CPU malfunction)
- C1532ECU internal malfunction (Peripheral circuit malfunction)
- C1532ECU internal malfunction (Peripheral circuit malfunction)
- C1533ECU internal malfunction (Substrate temperature sensor malfunction)
- C1533ECU internal malfunction (Substrate temperature sensor malfunction)
- C1534ECU internal malfunction (EEPROM error)
- C1534ECU internal malfunction (EEPROM error)
- C1541This DTC is detected when vehicle speed signals via CAN communication are cut off for 3 seconds or more.
- C1541This DTC is detected when vehicle speed signals via CAN communication are cut off for 3 seconds or more.
- C1541This DTC is detected when vehicle speed signals via CAN communication are cut off for 3 seconds or more.
- C1551IG power source circuit malfunction inside ECU
- C1551IG power source circuit malfunction inside ECU
- C1552PIG power source circuit malfunction inside ECU
- C1552PIG power source circuit malfunction inside ECU
- C1554Power source relay circuit malfunction
- C1554Power source relay circuit malfunction
- C1555Motor relay circuit malfunction
- C1555Motor relay circuit malfunction
- C1581Assist map not written in power steering ECU
- C1581Assist map not written in power steering ECU
- C1581Assist map not written in power steering ECU
- C1582Assist map number mismatch
- C1582Assist map number mismatch
- C1582Assist map number mismatch
- U0100Lost communication with ECM/PCM "A"
- U0100Lost communication with ECM/PCM "A"
- U0129Lost communication with brake system control module
- U0129Lost communication with brake system control module
- B15A5· Bus or sub-microprocessor malfunction · RAM malfunction · Internal hardware malfunction
- B15A5· Bus or sub-microprocessor malfunction · RAM malfunction · Internal hardware malfunction
- B1579Telephone microphone signal is lost.
- B1585USB Device Malfunction · Non mass-storage class or incompatible protocol USB device · USB device with an...
- B15A0When either condition below is met: · Bus malfunction · EEPROM error
- B15A0When either condition below is met: · Bus malfunction · EEPROM error
- B15ADWhen one of the conditions below is met: · A short to ground, short to +B or open occurs in the gyro signal...
- B15ADWhen one of the conditions below is met: · A short to ground, short to +B or open occurs in the gyro signal...
- B15B0Picture circuit (TFT unit) malfunction
- B15B0Picture circuit (TFT unit) malfunction
- B15B3When one of the conditions below is met: · AM tuner PLL is unlocked · FM tuner PLL is unlocked · Tuner...
- B15B3When one of the conditions below is met: · AM tuner PLL is unlocked · FM tuner PLL is unlocked · Tuner...
- B15B5When one of the conditions below is met: · Mechanism drive signal malfunction · Load/Eject malfunction · Read...
- B15B5When one of the conditions below is met: · Mechanism drive signal malfunction · Load/Eject malfunction · Read...
- B15B7"Bluetooth" module malfunction
- B15B7"Bluetooth" module malfunction
- B15C0Navigation antenna error
- B15C1Error of the power source to the navigation antenna
- B15C2A difference between the GPS speed and SPD pulse is detected.
- B15C2A difference between the GPS speed and SPD pulse is detected.
- B15D5B15D5
- B15F5Air conditioning amplifier assembly vehicle setting processing error.
- B15F5Air conditioning amplifier assembly vehicle setting processing error.
- B15F6Main body ECU vehicle setting processing error.
- B15F6Main body ECU vehicle setting processing error.
- B15F7Certification ECU vehicle setting processing error.
- B15F7Certification ECU vehicle setting processing error.
- U0073CAN bus connection error
- U0073CAN bus connection error
- U0100CAN reception error
- U0100CAN reception error
- U0129CAN reception error
- U0129CAN reception error
- U0140CAN reception error
- U0140CAN reception error
- U0155CAN reception error
- U0155CAN reception error
- C1AE1A malfunction of the front corner ultrasonic sensor (LH)
- C1AE4A malfunction of the front corner ultrasonic sensor (RH)
- C1AE6A malfunction of the rear corner ultrasonic sensor (LH)
- C1AE7A malfunction of the rear center ultrasonic sensor (LH)
- C1AE8A malfunction of the rear center ultrasonic sensor (RH)
- C1AE9A malfunction of the rear corner ultrasonic sensor (RH)
- C1AECAn open or short circuit in the communication line between the front sensors and clearance warning ECU...
- C1AEDAn open or short circuit in the communication line between the rear sensors and clearance warning ECU...
- U0101Lost communication with the ECM
- U0155Lost communication with the combination meter assembly
- C1622Open or short in the rear television camera assembly signal circuit
- C1625Open or short in steering angle sensor +B
- C1626A fail flag is transmitted from the steering sensor.
- C1691Back camera initial setting has not been memorized
- C1694Maximum steering angle has not been memorized
- U0126Lost communication with steering sensor
- U0126Lost communication with steering sensor
- U0140Lost communication with main body ECU (instrument panel junction block assembly)
- U0140Lost communication with main body ECU (instrument panel junction block assembly)
- B1207B1207
- B1216B1216
- B1216B1216
- B1217B1217
- B1217B1217
- B1287B1287
- B1287B1287
- B2326CAN MS Bus Line Communication Malfunction
- B2326CAN MS Bus Line Communication Malfunction
- U0182U0182
- U1002Lost Communication with Gateway Module
- B1000/31 Center airbag sensor assembly malfunction
- B1000/31 Center airbag sensor malfunction
- B1602/83 When one of following conditions is met: · Center airbag sensor detects line short signal, open signal, short...
- B1603/83 When one of following conditions is met: · Center airbag sensor detects line short signal, open signal, short...
- B1607/84 When one of following conditions is met: · Center airbag sensor detects line short signal, open signal, short...
- B1608/84 When one of following conditions is met: · Center airbag sensor detects line short signal, open signal, short...
- B1610/13 When one of the following condition is met: · Front airbag sensor RH malfunction · Center airbag sensor...
- B1610/13 · Front airbag sensor RH malfunction · Center airbag sensor assembly malfunction
- B1612/83 When one of following conditions is met: · Center airbag sensor detects line short signal, open signal, short...
- B1612/83 · The center airbag sensor assembly detects a line short, short to ground or B+, or an open in the front...
- B1613/83 When one of following conditions is met: · Center airbag sensor detects line short signal, open signal, short...
- B1613/83 · The center airbag sensor assembly detects a line short, short to ground or B+, or an open in the front...
- B1615/14 When one of following conditions is met: · Front airbag sensor LH malfunction · Center airbag sensor...
- B1615/14 · Front airbag sensor LH malfunction · Center airbag sensor assembly malfunction
- B1617/84 When one of following conditions is met: · Center airbag sensor detects line short signal, open signal, short...
- B1617/84 · The center airbag sensor assembly detects a line short, short to ground or B+, or an open in the front...
- B1618/84 When one of following conditions is met: · Center airbag sensor detects line short signal, open signal, short...
- B1618/84 · The center airbag sensor assembly detects a line short, short to ground or B+, or an open in the front...
- B1620/21 When one of following conditions is met: · Driver side - side airbag sensor (for front side) malfunction ·...
- B1620/21 · Side airbag sensor RH (for Front Side) malfunction · Center airbag sensor assembly malfunction
- B1622/81 When one of following conditions is met: · Center airbag sensor detects line short signal, open signal, short...
- B1622/81 · The center airbag sensor assembly detects a line short, short to ground or B+, or an open in the side...
- B1623/81 When one of following conditions is met: · Center airbag sensor detects line short signal, open signal, short...
- B1623/81 · The center airbag sensor assembly detects a line short, short to ground or B+, or an open in the side...
- B1625/22 When one of following conditions is met: · Front passenger side - side airbag sensor (for front side)...
- B1625/22 · Side airbag sensor LH (for Front Side) malfunction · Center airbag sensor assembly malfunction
- B1627/82 When one of following conditions is met: · Center airbag sensor detects line short signal, open signal, short...
- B1627/82 · The center airbag sensor assembly detects a line short, short to ground or B+, or an open in the side...
- B1628/82 When one of following conditions is met: · Center airbag sensor detects line short signal, open signal, short...
- B1628/82 · The center airbag sensor assembly detects a line short, short to ground or B+, or an open in the side...
- B1630/23 When one of following conditions is met: · Rear airbag sensor (for driver side) malfunction · Center airbag...
- B1630/23 · Rear airbag sensor RH malfunction · Center airbag sensor assembly malfunction
- B1632/81 When one of following conditions is met: · Center airbag sensor detects line short signal, open signal, short...
- B1632/81 · The center airbag sensor assembly detects a line short, short to ground or B+, or an open in the side...
- B1633/81 When one of following conditions is met: · Center airbag sensor detects line short signal, open signal, short...
- B1633/81 · The center airbag sensor assembly detects a line short, short to ground or B+, or an open in the side...
- B1635/24 When one of following conditions is met: · Rear airbag sensor (for front passenger side) malfunction · Center...
- B1635/24 · Rear airbag sensor LH malfunction · Center airbag sensor assembly malfunction
- B1637/82 When one of following conditions is met: · Center airbag sensor detects line short signal, open signal, short...
- B1637/82 · The center airbag sensor assembly detects a line short, short to ground or B+, or an open in the side...
- B1638/82 When one of following conditions is met: · Center airbag sensor detects line short signal, open signal, short...
- B1638/82 · The center airbag sensor assembly detects a line short, short to ground or B+, or an open in the side...
- B1642/81 When one of following conditions is met: · Center airbag sensor detects line short signal, open signal, short...
- B1642/81 · The center airbag sensor assembly detects a line short, short to ground or B+, or an open in the side...
- B1643/81 When one of following conditions is met: · Center airbag sensor detects line short signal, open signal, short...
- B1643/81 · The center airbag sensor assembly detects a line short, short to ground or B+, or an open in the side...
- B1647/82 When one of following conditions is met: · Center airbag sensor detects line short signal, open signal, short...
- B1647/82 · The center airbag sensor assembly detects a line short, short to ground or B+, or an open in the side...
- B1648/82 When one of following conditions is met: · Center airbag sensor detects line short signal, open signal, short...
- B1648/82 · The center airbag sensor assembly detects a line short, short to ground or B+, or an open in the side...
- B1657/95 · Side airbag sensor RH (for Rear Side) malfunction · Center airbag sensor assembly malfunction
- B1665/17 When one of following conditions is met: · Center floor airbag sensor malfunction · Center airbag sensor...
- B1665/17 · Center floor airbag sensor malfunction · Center airbag sensor assembly malfunction
- B1666/81 When one of following conditions is met: · Center airbag sensor detects line short signal, open signal, short...
- B1666/85 · The center airbag sensor assembly detects a line short, short to ground or B+, or an open in the side...
- B1667/81 When one of following conditions is met: · Center airbag sensor detects line short signal, open signal, short...
- B1667/85 · The center airbag sensor assembly detects a line short, short to ground or B+, or an open in the side...
- B1672/96 · Side airbag sensor LH (for Rear Side) malfunction · Center airbag sensor assembly malfunction
- B1673/81 · The center airbag sensor assembly detects a line short, short to ground or B+, or an open in the side...
- B1674/81 · The center airbag sensor assembly detects a line short, short to ground or B+, or an open in the side...
- B1675/18 · Rear floor airbag sensor malfunction · Center airbag sensor assembly malfunction
- B1675/82 When one of following conditions is met: · Rear floor airbag sensor malfunction · Center airbag sensor...
- B1678/82 When one of following conditions is met: · Center airbag sensor detects line short signal, open signal, short...
- B1678/86 · The center airbag sensor assembly detects a line short, short to ground or B+, or an open in the side...
- B1679/82 When one of following conditions is met: · Center airbag sensor detects line short signal, open signal, short...
- B1679/86 · The center airbag sensor assembly detects a line short, short to ground or B+, or an open in the side...
- B1684/82 · The center airbag sensor assembly detects a line short, short to ground or B+, or an open in the side...
- B1689/82 · The center airbag sensor assembly detects a line short, short to ground or B+, or an open in the side...
- B1690/15 When one of following conditions is met: · Driver side - side airbag sensor (for rear side) malfunction ·...
- B1692/81 When one of following conditions is met: · Center airbag sensor detects line short signal, open signal, short...
- B1693/81 When one of following conditions is met: · Center airbag sensor detects line short signal, open signal, short...
- B1695/16
- B1697/82 When one of following conditions is met: · Center airbag sensor detects line short signal, open signal, short...
- B1698/82 When one of following conditions is met: · Center airbag sensor detects line short signal, open signal, short...
- B1800/51 Center airbag sensor receives a line short signal 5 times in the driver side squib circuit during primary...
- B1800/51 · The center airbag sensor assembly detects a line short in the driver side squib circuit during the primary...
- B1801/51 Center airbag sensor receives an open signal in the driver side squib circuit for 2 seconds.
- B1801/51 · The center airbag sensor assembly detects an open in the driver side squib circuit. · Spiral cable...
- B1802/51 Center airbag sensor receives a short to ground signal in the driver side squib circuit for 0.5 seconds.
- B1802/51 · The center airbag sensor assembly detects a short to ground in the driver side squib circuit. · Spiral...
- B1803/51 Center airbag sensor receives a short to B+ signal in the driver side squib circuit for 0.5 seconds.
- B1803/51 · The center airbag sensor assembly detects a short to B+ in the driver side squib circuit. · Spiral cable...
- B1805/52 Center airbag sensor receives a line short signal 5 times in the front passenger side squib circuit during...
- B1805/52 · The center airbag sensor assembly detects a line short in the front passenger side squib circuit during the...
- B1806/52 Center airbag sensor receives an open circuit signal in the front passenger side squib circuit for 2 seconds.
- B1806/52 · The center airbag sensor assembly detects an open in the front passenger side squib circuit. · Front...
- B1807/52 Center airbag sensor receives a short to ground signal in the front passenger side squib circuit for 0.5...
- B1807/52 · The center airbag sensor assembly detects a short to ground in the front passenger side squib circuit. ·...
- B1808/52 Center airbag sensor receives a short to B+ signal in the front passenger side squib circuit for 0.5 seconds.
- B1808/52 · The center airbag sensor assembly detects a short to B+ in the front passenger side squib circuit. · Front...
- B1815/54 Center airbag sensor receives a line short signal 5 times in the front passenger side squib 2nd step circuit...
- B1815/54 · The center airbag sensor assembly detects a line short in the front passenger side squib 2nd step circuit...
- B1816/54 Center airbag sensor receives an open signal in the front passenger side squib 2nd step circuit for 2 seconds.
- B1816/54 · The center airbag sensor assembly detects an open in the front passenger side squib 2nd step circuit. ·...
- B1817/54 Center airbag sensor receives a short to ground signal in the front passenger side squib 2nd step circuit for...
- B1817/54 · The center airbag sensor assembly detects a short to ground in the front passenger side squib 2nd step...
- B1818/54 Center airbag sensor receives a short to B+ signal in the front passenger side squib 2nd step circuit for 0.5...
- B1818/54 · The center airbag sensor assembly detects a short to B+ in the front passenger side squib 2nd step circuit....
- B1820/55 Center airbag sensor receives a line short signal 5 times in the driver side front seat side squib circuit...
- B1820/55 · The center airbag sensor assembly detects a line short in the side squib RH circuit during the primary...
- B1821/55 Center airbag sensor receives an open signal in the driver side front seat side squib circuit for 2 seconds.
- B1821/55 · The center airbag sensor assembly detects an open in the side squib RH circuit. · Side squib RH malfunction...
- B1822/55 Center airbag sensor receives a short to ground signal in the driver side front seat side squib circuit for...
- B1822/55 · The center airbag sensor assembly detects a short to ground in the side squib RH circuit. · Side squib RH...
- B1823/55 Center airbag sensor receives a short to B+ signal in the driver side front seat side squib circuit for 0.5...
- B1823/55 · The center airbag sensor assembly detects a short to B+ in the side squib RH circuit. · Side squib RH...
- B1825/56 The center airbag sensor receives a line short signal 5 times in the front passenger side front seat side...
- B1825/56 · The center airbag sensor assembly detects a line short in the side squib LH circuit during the primary...
- B1826/56 Center airbag sensor receives an open signal in the front passenger side front seat side squib circuit for 2...
- B1826/56 · The center airbag sensor assembly detects an open in the side squib LH circuit. · Side squib LH malfunction...
- B1827/56 Center airbag sensor receives a short to ground signal in the front passenger side front seat side squib...
- B1827/56 · The center airbag sensor assembly detects a short to ground in the side squib LH circuit. · Side squib LH...
- B1828/56 Center airbag sensor receives a short to B+ signal in the front passenger side front seat side squib circuit...
- B1828/56 · The center airbag sensor assembly detects a short to B+ in the side squib LH circuit. · Side squib LH...
- B1830/57 Center airbag sensor receives a line short signal 5 times in the driver side curtain shield squib circuit...
- B1830/57 · The center airbag sensor assembly detects a line short in the curtain shield squib RH circuit during the...
- B1831/57 Center airbag sensor receives an open signal in the driver side curtain shield squib circuit for 2 seconds.
- B1831/57 · The center airbag sensor assembly detects an open in the curtain shield squib RH circuit. · Curtain shield...
- B1832/57
- B1832/57 Center airbag sensor receives a short to ground signal in the driver side curtain shield squib circuit for...
- B1833/57 Center airbag sensor receives a short to B+ signal in the driver side curtain shield squib circuit for 0.5...
- B1833/57 · The center airbag sensor assembly detects a short to ground in the curtain shield squib RH circuit. ·...
- B1835/58 Center airbag sensor receives a line short circuit signal 5 times in the front passenger side curtain shield...
- B1835/58 · The center airbag sensor assembly detects a line short in the curtain shield LH squib circuit during the...
- B1836/58 Center airbag sensor receives an open signal in the front passenger side curtain shield squib circuit for 2...
- B1836/58 · The center airbag sensor assembly detects an open in the curtain shield LH squib circuit. · Curtain shield...
- B1837/58 Center airbag sensor receives a short to ground signal in the front passenger side curtain shield squib...
- B1837/58 · The center airbag sensor assembly detects a short to ground in the curtain shield LH squib circuit. ·...
- B1838/58 center airbag sensor receives a short to B+ signal in the front passenger side curtain shield squib circuit...
- B1838/58 · The center airbag sensor assembly detects a short to B+ in the curtain shield LH squib circuit. · Curtain...
- B1840/59 Center airbag sensor receives a line short signal 5 times in the driver side curtain shield squib 2nd step...
- B1840/59 · The center airbag sensor assembly detects a line short in the curtain shield squib RH 2nd step circuit...
- B1841/59 Center airbag sensor receives an open signal in the driver side curtain shield squib 2nd step circuit for 2...
- B1841/59 · The center airbag sensor assembly detects an open in the curtain shield squib RH 2nd step circuit. ·...
- B1842/59 Center airbag sensor receives a short to ground signal in the driver side curtain shield squib 2nd step...
- B1842/59 · The center airbag sensor assembly detects a short to ground in the curtain shield squib RH 2nd step...
- B1843/59 Center airbag sensor receives a short to B+ signal in the driver side curtain shield squib 2nd step circuit...
- B1843/59 · The center airbag sensor assembly detects a short to B+ in the curtain shield squib RH 2nd step circuit. ·...
- B1845/61 Center airbag sensor receives a line short circuit signal 5 times in the front passenger side curtain shield...
- B1845/61 · The center airbag sensor assembly detects a line short in the curtain shield squib LH 2nd step circuit...
- B1846/61 Center airbag sensor receives an open signal in the front passenger side curtain shield squib 2nd step...
- B1846/61 · The center airbag sensor assembly detects an open in the curtain shield squib LH 2nd step circuit. ·...
- B1847/61 Center airbag sensor receives a short to ground signal in the front passenger side curtain shield squib 2nd...
- B1847/61 · The center airbag sensor assembly detects a short to ground in the curtain shield squib LH 2nd step...
- B1848/61 center airbag sensor receives a short to B+ signal in the front passenger side curtain shield squib 2nd step...
- B1848/61 · The center airbag sensor assembly detects a short to B+ in the curtain shield squib LH 2nd step circuit. ·...
- B1860/64 Center airbag sensor detects line short signal 5 times in driver side knee airbag squib circuit during...
- B1860/64 · The center airbag sensor assembly detects a line short in the driver side knee airbag squib circuit during...
- B1861/64 Center airbag sensor detects open signal in driver side knee airbag squib circuit for 2 seconds.
- B1861/64 · The center airbag sensor assembly detects an open in the driver side knee airbag squib circuit. · Driver...
- B1862/64 Center airbag sensor detects short to ground signal in driver side knee airbag squib circuit for 0.5 seconds.
- B1862/64 · The center airbag sensor assembly detects a short to ground in the driver side knee airbag squib circuit. ·...
- B1863/64 Center airbag sensor detects short to B+ signal in driver side knee airbag squib circuit for 0.5 seconds.
- B1863/64 · The center airbag sensor assembly detects a short to B+ in the driver side knee airbag squib circuit. ·...
- B1900/73 Center airbag sensor receives a line short signal 5 times in the driver side front pretensioner squib circuit...
- B1900/73 · The center airbag sensor assembly detects a line short in the front pretensioner squib RH circuit during...
- B1901/73 Center airbag sensor receives an open signal in the driver side front pretensioner squib circuit for 2...
- B1901/73 · The center airbag sensor assembly detects an open in the front pretensioner squib RH circuit. · Front...
- B1902/73 center airbag sensor receives a short to ground signal in the driver side front pretensioner squib circuit...
- B1902/73 · The center airbag sensor assembly detects a short to ground in the front pretensioner squib RH circuit. ·...
- B1903/73 Center airbag sensor receives a short circuit to B+ signal in the driver side front pretensioner squib...
- B1903/73 · The center airbag sensor assembly detects a short to B+ in the front pretensioner squib RH circuit. · Front...
- B1905/74 Center airbag sensor receives a line short signal 5 times in the front passenger side front pretensioner...
- B1905/74 · The center airbag sensor assembly detects a line short in the front pretensioner squib LH circuit during...
- B1906/74 Center airbag sensor receives an open signal in the front passenger side front pretensioner squib circuit for...
- B1906/74 · The center airbag sensor assembly detects an open in the front pretensioner squib LH circuit. · Front...
- B1907/74 Center airbag sensor receives a short to ground signal in the front passenger side front pretensioner squib...
- B1907/74 · The center airbag sensor assembly detects a short to ground in the front pretensioner squib LH circuit. ·...
- B1908/74 Center airbag sensor receives a short to B+ signal in the front passenger side front pretensioner squib...
- B1908/74 · The center airbag sensor assembly detects a short to B+ in the front pretensioner squib LH circuit. · Front...
- B1411/11 Open or short in room temperature sensor circuit
- B1412/12 Open or short in ambient temperature sensor circuit
- B1413/13 Open or short in evaporator temperature sensor circuit
- B1417/17 Open or short in rear air conditioning harness circuit (rear evaporator temperature sensor)
- B1419/19 Open or short in rear room temperature sensor circuit
- B1421/21 Open or short in passenger side solar sensor circuit
- B1422/22 Open or short in compressor lock sensor circuit
- B1422/22 Open or short in compressor lock sensor circuit
- B1423/23 Open or short in air conditioning pressure sensor circuit
- B1424/24 Open or short in driver side solar sensor circuit
- B1441/41 Air mix damper position does not change even if air conditioning amplifier operates air mix damper control...
- B1442/42 Air inlet damper position does not change even if air conditioning amplifier operates air inlet damper...
- B1443/43 Air outlet damper position does not change even if air conditioning amplifier operates air outlet damper...
- B1446/46 Air mix damper position does not change even if air conditioning amplifier operates air mix damper control...
- B1447/47 Rear air mix damper position does not change even if air conditioning amplifier operates rear air mix damper...
- B1449/49 Rear air outlet damper position does not change even if air conditioning amplifier operates rear air outlet...
- B1451/51 Open or short in solenoid of externally changeable compressor circuit
- B1497/97 Communication line error or open
- B1499/99 Open in CAN communication line
- B1499/99 Open in CAN communication line
- B14B9Open in No. 2 ion generator sub-assembly circuit
- B14B9Open in No. 2 ion generator sub-assembly circuit
- B2784Antenna coil open/short
- B2785LIN communication from certification ECU stops for specified amount of time
- B2789Certification ECU does not receive LIN communication signals from ID code box via LIN for 10 seconds
- B278AEngine switch power source supply line is open or short
- B2790ID code box detects internal malfunction
- B2791One of following conditions is met: · Communication failure between ID code box and ECM · Communication line...
- B2799One of following conditions is met: · Error in communication between ECM and ID code box · Error in...
- B279AWhen communication line (EFIO - IMI) between ECM and ID code box (immobiliser code ECU) is stuck on HI output.
- B279CWhen ECM that is incompatible with engine immobiliser system is installed.
- B279CWhen ECM that is incompatible with engine immobiliser system is installed.
- B1244Either of the following conditions is met: · Malfunction in automatic light control sensor · Open or short in...
- B2416· Malfunction in rear height control sensor sub-assembly LH · Open or short in rear height control sensor...
- B241A· Malfunction in rear height control sensor sub-assembly LH · Open or short in rear height control sensor...
- B2420Malfunction of headlight leveling ECU assembly
- B2430Any of the following conditions occur after 20 seconds have elapsed since the engine switch was turned on...
- B2431Any of the following conditions occur after 20 seconds have elapsed since the engine switch was turned on...
- B2450Initialization of the headlight leveling ECU assembly has not been performed
- B2451Vehicle specifications have not been stored
- B2452Rear height control sensor sub-assembly LH is out of range when initializing
- B2453The headlight leveling ECU assembly for another destination is installed on the vehicle
- B1244Automatic light control sensor malfunction
- B2410AFS ECU cannot communicate with headlight swivel motor LH normally for 1 second or more
- B2410AFS ECU cannot communicate with headlight swivel motor LH normally for 1 second or more
- B2411AFS ECU cannot communicate with headlight swivel motor RH normally for 1 second or more
- B2411AFS ECU cannot communicate with headlight swivel motor RH normally for 1 second or more
- B2412When one of following conditions is met: · Open or short between AFS ECU and headlight swivel motor LH ·...
- B2412When one of following conditions is met: · Open or short between AFS ECU and headlight swivel motor LH ·...
- B2413When one of following conditions is met: · Open or short between AFS ECU and headlight swivel motor RH ·...
- B2413When one of following conditions is met: · Open or short between AFS ECU and headlight swivel motor RH ·...
- B2414AFS ECU cannot receive signal from steering angle sensor normally
- B2414AFS ECU cannot receive signal from steering angle sensor normally
- B2415AFS ECU cannot receive signal from vehicle speed sensor normally
- B2415AFS ECU cannot receive signal from vehicle speed sensor normally
- B2416When one of conditions is met: · Height control sensor malfunction · Abnormal height control sensor power...
- B2416When one of conditions is met: · Height control sensor malfunction · Abnormal height control sensor power...
- B2417When one of following conditions is met: · Open or short between AFS ECU and headlight leveling motor LH ·...
- B2417When one of following conditions is met: · Open or short between AFS ECU and headlight leveling motor LH ·...
- B2418When one of following conditions is met: · Open or short between AFS ECU and headlight leveling motor RH ·...
- B2418When one of following conditions is met: · Open or short between AFS ECU and headlight leveling motor RH ·...
- B2420AFS ECU malfunction
- B2420AFS ECU malfunction
- B2421Steering angle sensor neutral point storage incomplete
- B2421Steering angle sensor neutral point storage incomplete
- B2423AFS ECU installation error
- B2423AFS ECU installation error
- B2424AFS ECU cannot communicate with headlight leveling motor LH normally for 1 second or more
- B2424AFS ECU cannot communicate with headlight leveling motor LH normally for 1 second or more
- B2425AFS ECU cannot communicate with headlight leveling motor RH normally for 1 second or more
- B2425AFS ECU cannot communicate with headlight leveling motor RH normally for 1 second or more
- B2427AFS ECU malfunction or CAN communication error
- B2427AFS ECU malfunction or CAN communication error
- B2450Initialization of the AFS ECU has not been performed
- B2450Initialization of the AFS ECU has not been performed
- B2452Vehicle condition not specified when initializing
- B2452Vehicle condition not specified when initializing
- B1500When IG voltage is 9.5 V or more and the following condition is detected: · Average input signal of fuel...
- B1507When IG voltage is 10 V or more and the following condition is detected: · Open in front turn signal light...
- B1508When IG voltage is 7 V or more and the following condition is detected: · Short in turn signal light circuit
- U0100When either of following conditions detected: 1. Vehicle speed 5 km/h or more and IG voltage 10.5 V or more...
- U0100w/o Multi-information Display: When either of the following conditions is detected: (a) Vehicle speed is 5...
- U0129When either of following conditions detected: 1. 15 seconds have elapsed since engine started and IG voltage...
- U0129w/o Multi-information Display: When either of the following conditions is detected: (a) Vehicle speed is 5...
- U0131When either of the following conditions is detected: 1. IG voltage is 9.5 V or more 2. No communication with...
- U0151When either of the following conditions is detected: 1. IG voltage is 9.5 V or more 2. No communication with...
- B1206No communication between multiplex network master switch and main body ECU for more than 10 seconds
- B2311When either condition below is met: (a) Power window regulator motor malfunctions (b) When ECU in power...
- B2311When either condition below is met: (a) Power window regulator motor malfunctions (b) When ECU in power...
- B2312Multiplex network master switch stuck
- B2313· Power window regulator motor not initialized · Power window regulator motor malfunctions
- B2313· Power window regulator motor not initialized · Power window regulator motor malfunctions
- B2321No communication between power window regulator motor (for driver side) and main body ECU for more than 10...
- B2322No communication between power window regulator motor (for front passenger side) and main body ECU for more...
- B2323No communication between power window regulator motor (for rear RH) and main body ECU for more than 10 seconds
- B2324No communication between power window regulator motor (for rear LH) and main body ECU for more than 10 seconds
- B2325Main body ECU detects door bus communication error (LIN communication malfunction) 3 times consecutively
- B2223A pulse sensor which is built in the slide door motor unit RH is malfunction.
- B2224A pulse sensor which is built in the slide door motor unit LH is malfunction.
- B2250While back door closer is operating, malfunction is detected in position information from each switch within...
- B2251While back door closer is operating, malfunction is detected in position information from each switch within...
- B2222Power back door unit does not operate
- B2225Voltage and current malfunction in clutch circuit of power back door unit
- B1273No communication from sliding roof drive gear for more than 10 seconds
- B2325B2325
- B2341Sensor (motor) failure
- B2342Sliding roof drive gear (rear sunshade control ECU) detects sliding roof control switch is stuck for 30...
- B2343Sliding roof drive gear (rear sunshade control ECU) has not been initialized
- B2344Position failure
Common jobs · 2AZ-FE (16)
- Read / clear codes
- DTC list
- Engine oil & filter: replacement
- Timing chain: inspection · replacement
- Ignition coil: removal · installation
- Drive belt: on-vehicle inspection · removal
- Coolant: replacement
- Water pump: inspection
- Thermostat: inspection · removal · installation
- Radiator: on-vehicle inspection · inspection · disassembly · reassembly
- Fuel pump: inspection · removal · installation
- Injectors: inspection · removal · installation
- Throttle body: on-vehicle inspection · inspection · removal · installation
- Cylinder head: replacement · disassembly · reassembly
- Alternator: inspection · replacement · removal · disassembly · reassembly · installation
- Starter: inspection · removal · disassembly · reassembly · installation
Common jobs · 2GR-FE (14)
- Read / clear codes
- DTC list
- Engine oil & filter: replacement
- Ignition coil: on-vehicle inspection · removal
- Drive belt: inspection · removal
- Water pump: inspection · removal
- Thermostat: inspection · removal
- Radiator: on-vehicle inspection · inspection · disassembly · reassembly
- Fuel pump: inspection · removal · disassembly · reassembly · installation
- Injectors: inspection · removal
- Throttle body: on-vehicle inspection · inspection · removal
- Engine assembly: on-vehicle inspection · inspection · removal · disassembly · reassembly
- Alternator: inspection · replacement · removal · disassembly · reassembly · installation
- Starter: inspection · removal · disassembly · reassembly · installation
Common jobs · chassis & body (7)
- Front brakes: inspection · removal · disassembly · reassembly · installation
- Rear brakes: inspection · removal · disassembly · reassembly · installation
- Brake fluid: on-vehicle inspection
- Parking brake: inspection · disassembly · reassembly
- Front drive shaft: removal · disassembly · reassembly
- Headlights: inspection · removal · disassembly · reassembly · installation · adjustment
- A/C refrigerant: on-vehicle inspection · replacement
Repair Manual
General283 documents
Engine / Hybrid System942 documents
Drivetrain535 documents
Suspension62 documents
Brake371 documents
Steering113 documents
Audio / Visual / Telematics367 documents
Power Source / Network81 documents
Vehicle Interior1468 documents
New Car Features
General13 documents
Engine / Hybrid System54 documents
Drivetrain19 documents
Suspension10 documents
Brake17 documents
Steering8 documents
Audio / Visual / Telematics26 documents
Power Source / Network22 documents
Vehicle Interior55 documents
Vehicle Exterior41 documents