Home › Vehicle Exterior › BODY PANEL › FIT STANDARD / ADJUSTMENT METHOD
BM24M0E _01 Vehicle Exterior _059852 BODY WELD POINT _0293730 FIT STANDARD / ADJUSTMENT METHOD F

BODY WELD POINT  FIT STANDARD / ADJUSTMENT METHOD  ADJUSTMENT  


INSPECT HOOD SUB-ASSEMBLY


a.

Check that the clearance measurements of areas A to F are within the standard range.

B140504E04
2.677,0.542 2.896,0.74 0.219,0.198 10 false A 0.802,2.292 1.021,2.49 0.219,0.198 10 false C 2.75,1.042 2.969,1.24 0.219,0.198 10 false B

Standard measurement:
Area Specified Condition
A 3.5 mm (0.138 in.)
B 0 mm (0 in.)
C 4.0 mm (0.157 in.)


HINT:

Centering bolts are used to mount the hood hinge and hood lock. The hood and hood lock cannot be adjusted with the centering bolts on. Substitute the centering bolts with standard bolts (with washers) when making adjustments.




ADJUST HOOD SUB-ASSEMBLY


B136611

a.

Adjust the hood's position.

i.

Loosen the hood's 4 hinge bolts.


ii.

Move the hood and adjust the clearance between the hood and front fender. Make sure that the clearance is within the standard range.


iii.

Tighten the hood's 4 hinge bolts after the adjustment.

Torque:
11.5 N*m (117 kgf*cm, 8 ft.*lbf)



b.
B136613

Adjust the cushion rubbers so that the height of the hood and fender are aligned.

i.
B136612E02
2.844,0.5 3.063,0.677 0.219,0.177 10 false A 2.604,2.365 3.094,2.594 0.49,0.229 10 true Aligned

Raise or lower the hood's front end by turning the cushion rubbers. Make sure that the clearance is within the standard range.

Standard measurement:
Area Specified Condition
A 3.5 mm (0.138 in.)




c.
B136911

Adjust the hood lock.

i.

Loosen the 3 bolts.


ii.
B136614

Adjust the hood lock position so that the striker can enter it smoothly.


iii.

Tighten the 3 bolts after the adjustment.

Torque:
7.5 N*m (77 kgf*cm, 66 in.*lbf)




INSPECT FRONT DOOR PANEL SUB-ASSEMBLY LH


a.

Check that the clearance measurements of areas A to E are within the standard range.

B462259E01
0.885,0.229 1.042,0.427 0.156,0.198 10 false A 0.958,0.844 1.115,1.042 0.156,0.198 10 false B 0.667,1.563 0.823,1.76 0.156,0.198 10 false C 5.146,0.25 5.302,0.448 0.156,0.198 10 false D 6.615,2.25 6.771,2.448 0.156,0.198 10 false E

Standard measurement:
Area Specified Condition
A 5.2 +-1.5 mm (0.205 +-0.098 in.)
B 9.4 +-1.5 mm (0.370 +-0.098 in.)
C 4.2 +-1.5 mm (0.165 +-0.098 in.)
D 4.7 +-1.5 mm (0.185 +-0.098 in.)
E 15.6 +-2.0 mm (0.614 +-0.079 in.)


HINT:
·

Use the same procedures for the RH side and LH side.

·

The procedures listed below are for the LH side.

·

Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute the centering bolts with standard bolts (with washers) when making adjustments.





ADJUST FRONT DOOR PANEL SUB-ASSEMBLY LH


B136636

a.

Using SST, loosen the body's hinge bolts and adjust the door's position.

SST
09812-00010  


b.

Tighten the body's hinge bolts after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


c.
B136635

Loosen the door's hinge bolts and adjust the door's position.


d.

Tighten the door's hinge bolts after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


e.
B136637

Using a T40 "TORX" socket, adjust the striker position by slightly loosening the striker mounting screws and then hitting the striker with a plastic-faced hammer.


f.

Using a T40 "TORX" socket, tighten the striker mounting screws after the adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)



INSPECT SLIDE DOOR PANEL SUB-ASSEMBLY LH


a.

Check that the clearance is within the standard range.

B139511E01
0.842,1.557 0.997,1.738 0.156,0.181 10 A 1.017,0.459 1.173,0.640 0.156,0.181 10 B 6.515,0.206 6.671,0.387 0.156,0.181 10 C 6.043,1.494 6.198,1.675 0.156,0.181 10 D

Standard measurement:
Area Specified Condition
A 4.7 +-1.5 mm (0.126 +-0.244 in.)
B 6.9 +-1.5 mm (0.213 +-0.331 in.)
C 4.7 +-1.5 mm (0.126 +-0.244 in.)
D 15 +-2.0mm (0.512 +-0.669 in.)


HINT:
·

Use the same procedures for the RH side and LH side.

·

The procedures listed below are for the LH side.

·

Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute the centering bolts with standard bolts (with washers) when making adjustments.





ADJUST SLIDE DOOR PANEL SUB-ASSEMBLY LH


a.
B139512

Using SST, horizontally and vertically adjust the door by loosening the 3 hinge assembly center bolts.

SST
09812-00010  
09812-00020  


b.

Tighten the hinge assembly center bolts after the adjustment.

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)


c.
B139513

Vertically adjust the front side of the door by loosening the 3 roller lower bolts.


d.

Tighten the roller lower bolts after the adjustment.

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)


e.
B139514

Horizontally adjust the front lower side of the door by loosening the roller lower bolt.


f.

Tighten the roller lower bolt after the adjustment.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


g.
B139515

Horizontally adjust the front upper side of the door by loosening the roller upper bolts.


h.

Tighten the roller upper bolts after the adjustment.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


i.
B058863

Adjust the position of the 2 door lock strikers by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.


j.

Tighten the 2 striker mounting screws after the adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)



INSPECT BACK DOOR PANEL SUB-ASSEMBLY


a.

Check that the clearance is within the standard range.

B139526E02
1.708,2 1.865,2.177 0.156,0.177 10 false A 1.906,0.167 2.063,0.344 0.156,0.177 10 false B 5.656,1.083 5.813,1.26 0.156,0.177 10 false C 5.677,2.365 5.833,2.542 0.156,0.177 10 false D

Standard measurement:
Area Specified Condition
A 7.9 +-1.5 mm (0.252 +-0.37 in.)
B 7.2 +-1.5 mm (0.224 +-0.343 in.)
C 6.4 +-1.5 mm (0.193 +-0.311 in.)
D 4.1 +-1.5 mm (0.102 +-0.22 in.)


HINT:
·

Use the same procedures for the RH side and LH side.

·

The procedures listed below are for the LH side.

·

Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute the centering bolts with standard bolts (with washers) when making adjustments.





ADJUST BACK DOOR PANEL SUB-ASSEMBLY


a.
B139527

Adjust the door forward/rearward and vertically by loosening the body side hinge.


b.

Tighten the body side hinge after the adjustment.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


c.

Using a screwdriver, remove the back door scuff plate.

HINT:

Tape the screwdriver tip before use.



d.
B139528

Adjust the striker position by slightly loosening the 2 striker mounting screws and hitting the striker with a plastic-faced hammer.


e.

Tighten the striker mounting screws after the adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)