Home › Vehicle Exterior › BODY PANEL › CENTER BODY PILLAR
BM24M0E _01 Vehicle Exterior _059852 BODY WELD POINT _0293742 CENTER BODY PILLAR F

BODY WELD POINT  CENTER BODY PILLAR  CUT AND JOIN REPLACEMENT SECTIONS  


K133138

REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108820

Remove Weld Points
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts

REMOVAL POINT
1.

*a: Take care not to damage the internal reinforcement.


K133180C01
0.917,1.75 1.344,1.469 false 0.917,1.75 1.385,1.833 false 0.708,1.677 1.021,1.833 0.313,0.156 10 false *a 4.167,1.344 4.771,1.74 0.604,0.396 10 false 50 (1.97) 6.844,8.552 7.156,8.708 0.313,0.156 10 false *b 6.427,1.625 7.031,2.094 0.604,0.469 10 false 60 (2.36) 1.323,6.958 2.042,7.344 0.719,0.385 10 false 320 (12.60) 2.073,7.25 2.667,7.625 0.594,0.375 10 false 80 (3.15) 5.115,7.615 5.844,7.938 0.729,0.323 10 false 400 (15.75) 4.219,1.594 4.823,1.99 0.604,0.396 10 false 50 (1.97)
*b mm (in.) - -



INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108825

Plug Weld
K108827

Cut and Join Location
K108831

Butt Weld

INSTALLATION POINT
1.

Before temporarily installing the new parts, weld the rocker panel no. 2 reinforcement, center body pillar upper reinforce and center body pillar with the standard number of welding points.

2.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

3.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

4.

After welding the rocker panel no. 2 reinforcement, center body pillar upper reinforce and center body pillar to the vehicle side, install the center body outer pillar and rocker outer panel.

5.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting / coating)

6.

After welding, apply body sealer and undercoating to the corresponding parts. (See the painting / coating)

7.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K133181C01
1.531,2.854 1.531,2.188 false 5.313,4.042 5.313,3.625 false 1.333,7.333 1.854,6.813 false 1.469,2.875 1.781,3.031 0.313,0.156 10 false *1 5.26,4.063 5.573,4.219 0.313,0.156 10 false *2 1.198,7.354 1.51,7.51 0.313,0.156 10 false *3 6.844,8.552 7.156,8.708 0.313,0.156 10 false *a 1.281,1.417 2.781,1.646 1.5,0.229 10 false 390 (15.35) 5.948,1.083 6.656,1.469 0.708,0.385 10 false 95 (3.74) 2.396,5.167 3.063,5.646 0.667,0.479 10 false 40 (1.57)
*1 Rocker Panel No.2 Reinforcement *2 Center Body Pillar Upper Reinforce
*3 Center Body Pillar - -
*a mm (in.) - -


K133182C01
5.313,4 5.906,3.979 false 2.292,6.74 2.729,6.75 false 2.417,7.906 2.604,8.469 false 5.969,3.875 6.281,4.031 0.313,0.156 10 false *1 2.76,6.656 3.073,6.813 0.313,0.156 10 false *2 2.563,8.49 2.875,8.646 0.313,0.156 10 false *3
*1 Center Body Pillar *2 Center Body Outer Pillar
*3 Rocker Outer Panel - -