Home › Vehicle Exterior › BODY PANEL › REAR FLOOR STEP
BM24M0E _01 Vehicle Exterior _059852 BODY WELD POINT _0293746 REAR FLOOR STEP F

BODY WELD POINT  REAR FLOOR STEP  ASSEMBLY REPLACEMENT  


K133143

With the center body pillar, rocker outer panel and quarter panel removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108820

Remove Weld Points
K108827

Cut and Join Location
K108826

Cut with Disc Sander etc.

REMOVAL POINT
1.

After removing the floor side inner member, floor side rail plate, seat belt anchor no.2 reinforcement, quarter wheel housing outer panel and roof side inner front panel no.2 remove the rear floor step.


K133189C01
1.927,1.979 2.219,1.448 false 4.448,2 4.948,2.167 false 5.417,3.365 5.615,3.76 false 5.938,7.083 6.052,7.458 false 2.802,7.813 3.115,7.969 0.313,0.156 10 false *A 2.802,8.021 3.115,8.177 0.313,0.156 10 false *B 2.198,1.25 2.51,1.406 0.313,0.156 10 false *1 4.26,1.875 4.573,2.031 0.313,0.156 10 false *2 5.604,3.781 5.917,3.938 0.313,0.156 10 false *3 6.01,7.479 6.323,7.635 0.313,0.156 10 false *4 6.844,8.552 7.156,8.708 0.313,0.156 10 false *a 6.573,2.323 7.156,2.771 0.583,0.448 10 false 60 (2.36) 1.771,5.167 2.531,5.656 0.76,0.49 10 false 485 (19.09)
*A LH *B RH
*1 Floor Side Inner Member *2 Seat Belt Anchor No.2 Reinforcement
*3 Quarter Wheel Housing Outer Panel *4 Floor Side Rail Plate
*a mm (in.) - -


K133190C01
2.542,2.063 3.073,2.323 false 2.875,7.219 3.188,7.375 0.313,0.156 10 false *A 3.125,2.292 3.438,2.448 0.313,0.156 10 false *1
*A RH - -
*1 Roof Side Inner Front Panel No.2 - -


K133191C01
2.344,6.552 2.656,6.708 0.313,0.156 10 false *A
*A LH - -



INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108824

Plug Weld
K108825

Plug Weld
K108831

Butt Weld

INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

After welding the rear floor step to the vehicle side, install the floor side inner member, floor side rail plate, seat belt anchor no.2 reinforcement, quarter wheel housing outer panel and roof side inner front panel no.2.

4.

After welding, apply body sealer and undercoating to the corresponding parts. (See the painting / coating)

5.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K133192C01
2.208,6.01 2.521,6.167 0.313,0.156 10 false *A
*A RH - -


K133193C01
2.313,6.552 2.625,6.708 0.313,0.156 10 false *A
*A LH - -


K133194C01
5.635,8.583 5.438,8.135 false 4.417,6.802 4.958,6.948 false 2.24,5.583 2.927,5.875 false 5.688,3.698 5.948,3.104 false 4.938,1.885 5.719,1.094 false 1.74,2.99 2.052,3.146 0.313,0.156 10 false *A 1.74,3.208 2.052,3.365 0.313,0.156 10 false *B 5.771,0.917 6.083,1.073 0.313,0.156 10 false *1 5.927,2.917 6.24,3.073 0.313,0.156 10 false *2 2.99,5.844 3.302,6 0.313,0.156 10 false *3 4.24,6.688 4.552,6.844 0.313,0.156 10 false *4 5.615,8.594 5.927,8.75 0.313,0.156 10 false *5
*A LH *B RH
*1 Floor Side Rail Plate *2 Floor Side Inner Member
*3 Roof Side Inner Front Panel No.2 *4 Seat Belt Anchor No.2 Reinforcement
*5 Quarter Wheel Housing Outer Panel - -