Home › Vehicle Exterior › BODY DIMENSIONS › MEASURING INFORMATION
BM24M0E _01 Vehicle Exterior _059853 BODY DIMENSIONS _0293772 MEASURING INFORMATION F

BODY DIMENSIONS  MEASURING INFORMATION  DIAGRAM DESCRIPTION  


HINT:
·

There are two types of dimensions in the diagram.

·

In cases in which only one dimension is given, left and right are symmetrical.

·

For symbols, capital letters indicate right side of vehicle, small letters indicate left side of vehicle (seen from rear).



Three-Dimensional Distance


K104022C04
1.615,0.135 1.844,0.292 0.229,0.156 10 true *a
*a Distance between the centers of the measuring points


a.

Straight-line distance between the centers of two measuring points.



Two-Dimensional Distance


K111552C01
1.083,3.083 1.333,3.25 1.333,3.25 1.5,3.25 false 1.906,1.125 2.219,1.281 0.313,0.156 10 true *a 1.698,2.667 2.01,2.823 0.313,0.156 10 true *b 2.604,2.417 2.917,2.573 0.313,0.156 10 true *c 1.573,3.177 1.885,3.333 0.313,0.156 10 false *d
*a Center-to-center horizontal distance in forward/rearward
*b Vertical distance to center
*c Vertical distance to lower surface
*d Imaginary Datum Line


a.

Horizontal distance in forward/rearward between the centers of two measuring points.


b.

Distance from the Imaginary Datum Line.



Imaginary Datum Line


K111553C01
0.875,0.552 1.25,0.833 1.25,0.833 1.417,0.833 false 0.813,1.781 1,2 1,2 1.167,2 false 1.479,0.76 1.792,0.917 0.313,0.156 10 false *a 1.229,1.917 1.542,2.073 0.313,0.156 10 false *b 0.271,1.51 0.583,1.667 0.313,0.156 10 false (1) 1.479,1.51 1.792,1.667 0.313,0.156 10 false (2) 2.677,1.51 2.99,1.667 0.313,0.156 10 false (3) 0.448,1.833 0.76,1.99 0.313,0.156 10 false A 2.854,1.833 3.167,1.99 0.313,0.156 10 false C 1.656,1.844 1.969,2 0.313,0.156 10 false B
*a Under surface of the Rocker Panel
*b Imaginary Datum Line


a.

The imaginary line used to measure height is a line which connects the points described in the following chart (actual dimensions are listed in the next chapter of this manual).

Symbol Measuring Points
A The place that was lowered (1) mm (in.) from the under surface of the rocker panel centered on the front jack up point.
B The place that was lowered (2) mm (in.) from the under surface of the rocker panel centered between A and C.
C The place that was lowered (3) mm (in.) from the under surface of the rocker panel centered on the rear jack up point.



Measurement


K111554C01
0.083,2.833 1.667,4.583 1.583,1.75 1.75,2.833 3.333,4.583 1.583,1.75 0.833,0.75 1,0.75 1,0.75 1.25,1 false 0.667,1.833 0.396,1.833 false 2.25,1.833 2.25,2.083 false 1.167,3.917 0.885,3.917 false 2.833,3.917 2.563,3.917 false 0.667,0.677 0.979,0.833 0.313,0.156 10 false *a 2.177,2.125 2.49,2.281 0.313,0.156 10 false *b 0.75,1.75 1.063,1.906 0.313,0.156 10 false *c 0.167,2.927 0.479,3.083 0.313,0.156 10 false *d 1.833,2.917 2.146,3.073 0.313,0.156 10 false *e 1.25,3.844 1.563,4 0.313,0.156 10 false *c 2.917,3.833 3.229,3.99 0.313,0.156 10 false *c
*a Tracking Gauge
*b Master Gauge
*c Pointer
*d Wrong
*e Correct


a.

Basically, all measurements are to be done with a tracking gauge. For portions where it is not possible to use a tracking gauge, a tape measure should be used.


b.

Use only a tracking gauge that has no looseness in the body, measuring plate, or pointers.

HINT:
·

The height of the left and right pointers must be equal.

·

Always calibrate the tracking gauge before measuring or after adjusting the pointer height.

·

Take care not to drop the tracking gauge or otherwise shock it.

·

Confirm that the pointers are securely in the holes.




c.

When using a tape measure, avoid twists and bends in the tape.