Home › Suspension › REAR SUSPENSION › REAR SUSPENSION SYSTEM
NM24M0E _53 Suspension _061440 REAR SUSPENSION _0299857 REAR SUSPENSION SYSTEM UN GENERAL/CONTROL/DETAILS F

REAR SUSPENSION  REAR SUSPENSION SYSTEM  GENERAL/CONTROL/DETAILS  GENERAL  


OUTLINE


a.

A lightweight, compact, and highly rigid torsion-beam type suspension is used.


b.

The characteristics of the trailing arm bushing have been optimized to realize excellent driving stability and ride comfort.


c.

The suspension geometry has been optimized to realize excellent driving stability and ride comfort.


d.

A pipe structural beam with the stabilizer function is used for the axle beam.


e.

The rolling rigidity has been optimized to realize excellent vehicle stability.

X135902C01
2.865,1.76 3.615,1.177 3.615,1.177 3.948,1.177 true 4.552,3.167 5.052,0.833 5.052,0.833 5.385,0.833 true 4.385,2.427 4.885,0.427 4.885,0.427 5.219,0.427 true 5.25,2.229 5.667,1.781 5.667,1.781 6,1.781 true 2.323,3.167 2.656,3.167 2.656,3.167 2.823,2.583 true 1.167,2.76 1.5,2.76 1.5,2.76 1.667,2.177 true 4.01,1.094 4.323,1.292 0.313,0.198 10 false *1 5.281,0.333 5.594,0.531 0.313,0.198 10 false *2 5.458,0.75 5.771,0.948 0.313,0.198 10 false *2 6.052,1.698 6.365,1.896 0.313,0.198 10 false *3 0.979,2.688 1.292,2.885 0.313,0.198 10 false *4 2.135,3.094 2.448,3.292 0.313,0.198 10 false *5
*1 Coil Spring
·

Optimized spring constant


*2 Spring Seats
·

Optimized characteristics


*3 Shock Absorber
·

Optimized characteristics


*4 Trailing Arm Bushing
·

Optimized characteristics


*5 Axle Beam
·

A beam with a pipe structure is used


- -




NOTICE:

Be sure to use the jack-up points that are provided on the body when raising the vehicle on the jack. Never apply a jack under the axle beam, spring seat, trailing arm, or bushing of the rear suspension.


SPECIFICATION


*1: Unloaded Vehicle Condition

*2: With 205/65R16 Tire

*3: With 215/55R17 Tire

Type Torsion Beam
Tread*1 mm (in.) 1575 (62.0)*2, 1550 (61.0)*3
Camber*1 degrees -1° 24'
Toe-in*1 mm (in.) 3.3 (0.13)


MAIN FEATURES


a.

Toe and Camber Change

i.

In a torsion-beam type suspension, the camber angle and the toe change differ between the bouncing case and the tramping case, offering both straight-line stability and excellent cornering stability.

1.

Bouncing Case

Similar to the full-trailing arm type suspension, the axis that joins the center of the right and left trailing arm bushings is the center of the movement.

2.

Tramping Case

In tramping case, or if a difference in suspension travel is created between the right and left wheels, the torsion beam twists with its shearing center as the center of its rotation.

Also, camber changes in relation to the suspension travel are determined by the ratio of the distance between the No. 1 trailing arm bushing, the axle center and the shearing center ('a' in the figure below) and distance between the No. 1 trailing arm bushing and the axle beam ('L' in the figure below).

Consequently, through the optimal allocation of the axle beam, the changes in the camber angle in relation to the suspension travel have been optimized, thus ensuring excellent cornering performance.

X135981E01
1.646,1.802 1.896,1.802 1.896,1.802 1.969,2.042 true 1.865,2.531 2.115,2.531 2.115,2.531 2.365,2.365 true 1.208,1.021 1.458,1.021 1.458,1.021 1.792,1.521 true 2.198,0.302 2.448,0.302 2.448,0.302 2.615,0.635 true 2.75,1.167 3.333,1.417 3.333,1.417 3.5,1.417 true 1.021,0.229 2.365,0.51 1.344,0.281 10 false Center of Bushing 0.063,0.948 1.406,1.229 1.344,0.281 10 false Center of Bushing 0.073,1.729 1.854,2.01 1.781,0.281 10 false Camber Change Rate a/L 0.094,2.469 1.969,2.719 1.875,0.25 10 false Camber Change Rate 100 % 4.188,0.656 5.021,0.885 0.833,0.229 10 false BOUND 3.521,1.938 4.542,2.208 1.021,0.271 10 false REBOUND 3.573,1.323 4.479,1.906 0.906,0.583 10 false Instantaneous Center of Axle 4.792,1.125 6.813,1.896 2.021,0.771 10 false An alignment change that is very close to that of the semi-trailing suspension is effected.




b.

Anti-Lift Geometry

i.

The lifting of the rear end of the vehicle during braking occurs due to the shifting of the center of gravity caused by inertia.

The intersecting point (OR) supports the braking force (BF), and generates a force (BF1) in the direction of the intersecting point and a component force (BF2) in the direction of the ground contact.

The force (BF1) can change the height of the intersecting point (OR). When OR is set high, it acts in the opposite direction (-W) of the load fluctuation (W) in order to restrain the lift.

X135909E01
1.865,1.583 2.177,1.781 0.313,0.198 10 false OR 3.25,2.146 3.563,2.344 0.313,0.198 10 false BF2 4.219,2.458 4.531,2.656 0.313,0.198 10 false BF 4.25,3.115 4.563,3.313 0.313,0.198 10 false BF1 3.271,2.979 3.583,3.177 0.313,0.198 10 false W 3.208,3.427 3.698,3.719 0.49,0.292 10 false -W



c.

Toe-correct Function

i.

The longitudinal and lateral forces that are created in the vehicle during cornering cause the trailing arm bushings to deform.

On a right turn, the right trailing arm moves forward and the left trailing arm moves rearward, creating a tendency for the left wheel to toe out.

In this situation, the bushings that are installed in the trailing arms are designed to utilize the lateral force, which is applied to the bushings during cornering, to correct the left trailing arm towards the toe-in direction. A toe correction structure is added to the new bushing rear portion. Thus, excellent vehicle stability has been realized through the increase in the amount of toe correction.

X135971E01
1.542,1.792 1.792,1.792 1.792,1.792 2.042,1.458 true 1.708,2.625 1.958,2.625 1.958,2.625 2.042,2.958 true 1.333,0.979 1.583,0.979 1.583,0.979 1.646,1.427 true 2.406,0.531 2.656,0.531 2.656,0.531 2.823,0.906 true 4.458,0.188 4.708,0.188 4.708,0.188 4.729,0.969 true 4.115,1.635 4.365,1.635 4.365,1.635 4.479,1.417 true 5.344,0.833 5.594,0.583 5.594,0.583 5.844,0.583 true 1.5,0.448 2.698,0.688 1.198,0.24 10 false Lateral Force 0.167,0.906 1.365,1.146 1.198,0.24 10 false Longitudinal Force 1,1.719 1.74,2.01 0.74,0.292 10 false Bushing 1.146,2.552 1.885,2.844 0.74,0.292 10 false Bushing 2.958,0.115 4.417,0.5 1.458,0.385 10 false Lateral Force Applied to the Bushing 2.917,1.552 4.135,2.042 1.219,0.49 10 false Bushing Movement 5.917,0.51 6.854,0.813 0.938,0.302 10 false Lateral Force 3.427,3.156 4.625,3.396 1.198,0.24 10 false Left Wheel 5.844,3.146 7.042,3.385 1.198,0.24 10 false Left Wheel

Trailing Arm Bushing
X136191E01
2.031,0.115 2.365,0.115 2.365,0.115 2.448,0.198 true 0.385,0.052 2.427,0.375 2.042,0.323 10 false Longitudinal Displacement 1.115,1.146 1.781,1.469 0.667,0.323 10 false Front 2.719,2.146 3.542,2.406 0.823,0.26 10 false Side Force 2.448,2.5 2.875,2.75 0.427,0.25 10 false New 5.219,2.49 6.208,2.74 0.99,0.25 10 false Previous