Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE CONTROL SYSTEM › 2013.04–2016.05
NM24M0E _54 Brake _061442 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0299859 BRAKE CONTROL SYSTEM UN GENERAL/CONTROL/DETAILS F

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE CONTROL SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


SYSTEM CONTROL


a.

The outlines for the respective brake control functions are as follows:

Function Outline
ABS (Anti-lock Brake System) The ABS helps prevent the wheels from locking when the brake is applied firmly or applied on a slippery surface.
EBD (Electronic Brake force Distribution) The EBD control utilizes the ABS, realizing the proper brake force distribution between the front and rear wheels in accordance with the driving conditions. In addition, during cornering braking, it also controls the brake forces of the right and left wheels, helping to maintain the vehicle behavior.
Brake Assist (Mechanical Type or Electrical Type) The primary purpose of the Brake Assist function is to provide an auxiliary brake force to assist the driver who cannot generate a large brake force during emergency braking, thus helping draw the vehicle's brake performance.
TRC (Traction Control) The TRC function helps prevent the drive wheels from slipping if the driver depresses the accelerator pedal excessively when starting off or accelerating on a slippery surface.
VSC (Vehicle Stability Control) The VSC function helps prevent the vehicle from slipping sideways as a result of strong front wheel skid or strong rear wheel skid during cornering.
Cooperative Control with EPS The cooperative control with the EPS ECU provides steering assist in accordance with the operating conditions of the vehicle.

HINT:

Service Tip:

When brake control system (except mechanical type Brake Assist) is activated, the brake pedal could shudder, which is a normal occurrence of the system in operation and should not be considered as a malfunction.



b.

VSC+ System

i.

In the past, the brake control functions (ABS, TRC, VSC) and the EPS were controlled individually.In contrast, the new model uses a VSC+ system. This system uses a cooperative control function that effects integrated control of the brake control functions and the EPS in accordance with driving conditions. Thus, it improves the dynamic performance of the vehicle to "run, turn, and stop" and ensures excellent driving stability and drivability.

X135911E01
2.083,2.604 2.906,2.854 0.823,0.25 10 false EPS ECU 1.74,2.938 3.01,4.115 1.271,1.177 10 false Controls the steering motor after calculating required steering assist torque 3.938,2.583 5.198,2.844 1.26,0.26 10 false Skid Control ECU 3.792,2.885 5.01,3.396 1.219,0.51 10 false - Detects a state of the vehicle 3.792,3.344 5.167,4.021 1.375,0.677 10 false - Request the steering assist torque and engine output 4.083,4.406 4.906,4.656 0.823,0.25 10 false Engine ECU 3.875,4.75 5.094,5.75 1.219,1 10 false Controls the throttle motor upon receiving the request for engine output control 3.75,6.281 5.188,6.823 1.438,0.542 9 false Yaw Rate & Deceleration Sensor 1.958,6.271 2.875,6.698 0.917,0.427 10 false Steering Angle Sensor 5.656,5.344 6.917,5.615 1.26,0.271 9 false Neutral Start Switch 5.667,5.521 6.708,5.938 1.042,0.417 9 false Accelerator Pedal Position Sensor 5.646,5.094 7.104,5.313 1.458,0.219 9 false Throttle Position Sensor 5.646,4.76 6.865,5.125 1.219,0.365 9 false Crankshaft Position Sensor 5.656,4.417 6.729,4.646 1.073,0.229 10 false Throttle Motor 5.635,3.5 6.875,3.865 1.24,0.365 10 false Stop Light Switch 5.646,2.906 6.938,3.302 1.292,0.396 10 false Speed Sensor 5.281,7.281 7.156,7.833 1.875,0.552 9 false : CAN (Controller Area Network)



c.

Outline of EBD

i.

General

1.

The distribution of the brake force, which was performed mechanically in the past, is now performed under electrical control of the skid control ECU, which controls the brake force in accordance with the vehicle's driving conditions.



ii.

Front/Rear Wheels Brake Force Distribution

1.

If the brakes are applied while the vehicle is moving straight forward, the transfer of the load reduces the weight that is applied to the rear wheels. The skid control ECU determines this condition by way of the signals from the yaw rate & deceleration sensor, and the brake actuator regulates the distribution of the brake force to the rear wheels to optimally control.

For example, the amount of the brake force that is applied to the rear wheels during braking varies depending on whether the vehicle is carrying load or not. The amount of the brake force that is applied to the rear wheels also varies in accordance with the extent of the deceleration.

Thus, the distribution of the brake force to the rear wheels is optimally controlled in order to effectively utilize the brake force of the rear wheels under these conditions.

EBD Control Concept
X135973E01
5.198,3.594 5.365,3.76 5.365,3.76 5.615,3.76 true 1.365,3.604 1.51,2.781 1.51,2.781 1.844,2.781 true 4.813,3.521 4.875,2.427 4.875,2.427 5.208,2.427 true 1.479,3.646 1.646,3.813 1.646,3.813 1.896,3.813 true 0.115,3.156 0.833,3.646 0.719,0.49 10 false Rear Brake Force 3.74,3.188 4.458,3.677 0.719,0.49 10 false Rear Brake Force 1.938,2.688 3.875,2.979 1.938,0.292 10 false Ideal Brake Force Distribution 5.292,2.344 7.156,2.667 1.865,0.323 10 false Ideal Brake Force Distribution 1.969,3.729 2.948,4.01 0.979,0.281 10 false EBD Control 5.698,3.667 6.677,3.948 0.979,0.281 10 false EBD Control 1.573,4.115 2.958,4.333 1.385,0.219 10 false Front Brake Force 5.167,4.104 6.479,4.385 1.313,0.281 10 false Front Brake Force 5.177,4.427 6.75,4.729 1.573,0.302 10 false With Load in Rear 1.51,4.427 3.083,4.729 1.573,0.302 10 false Without Load in Rear



iii.

Right/Left Wheels Brake Force Distribution (During Cornering Braking)

1.

When the brakes are applied while the vehicle is cornering, the load that is applied to the inner wheel decreases as the load to the outer wheel increases.

The skid control ECU determines this condition by way of the signals from the speed sensor, and the brake actuator regulates the brake force in order to optimally control the distribution of the brake force to the inner wheel and outer wheel.

X135972




d.

Outline of Brake Assist

i.

The Brake Assist in combination with the ABS helps ensure the vehicle's brake performance.


ii.

The Brake Assist interprets a quick push of the brake pedal as emergency braking and supplements the brake force applied if the driver has not depressed hard enough the brake pedal. In emergencies, drivers, especially inexperienced ones, often panic and do not apply sufficient pressure on the brake pedal.


iii.

A key feature of Brake Assist is that the timing and the degree of braking assistance are designed to help ensure that the driver does not discern anything unusual about the braking operation. When the driver intentionally eases up on the brake pedal, the system reduces the amount of assistance it provides.


iv.

The mechanical type brake assist uses the brake assist mechanism in the brake booster to mechanically activate the brake booster function in order to increase the brake force.


v.

In the electrical type brake assist, based on the signals from the master cylinder pressure sensor, the skid control ECU calculates the speed and the amount of the brake pedal application and then determines the intention of the driver to make an emergency braking. If the skid control ECU determines that the driver intends the emergency braking, this function activates the brake actuator to increase the brake fluid pressure, which increases the brake force.

In case that the driver's depressing force is small when emergency braking is applied
X136198E01
1.063,2.156 1.292,0.583 1.292,0.583 1.542,0.583 true 4.25,0.5 5.49,0.74 1.24,0.24 10 false Skid Control ECU 1.615,0.5 2.854,1.365 1.24,0.865 10 false The fluid pressure is increased by the brake booster 0.729,3.573 3.104,3.979 2.375,0.406 10 false With Brake Assist (Mechanical Type) 4.073,3.583 6.281,4.042 2.208,0.458 10 false With Brake Assist (Electrical Type) 2.906,1.052 3.885,1.802 0.979,0.75 10 false Master Cylinder Pressure Sensor Signal 4.75,1.063 5.844,1.927 1.094,0.865 9 false The fluid pressure is increased by the brake actuator 5.958,1.052 7.073,1.802 1.115,0.75 10 false Brake Pedal Load Sensing Switch Signal 0.125,6.542 6.24,6.781 6.115,0.24 10 false *: The basic performance of the brake is the same as that of the models with the Brake Assist 1.198,6.146 2.823,6.427 1.625,0.281 10 false Without Brake Assist* 3.26,5.083 4.5,5.323 1.24,0.24 10 false Brake Force 4.75,4.677 5.99,4.917 1.24,0.24 10 false With Brake Assist 4.76,5.271 6.396,5.646 1.635,0.375 10 false Without Brake Assist 5.135,6.104 5.813,6.323 0.677,0.219 10 false Time



e.

Outline of TRC

i.

If the driver depresses the accelerator pedal aggressively when starting off or accelerating on a slippery surface, the drive wheels could slip due to the excessive amount of torque that is generated. By applying hydraulic brake control to the drive wheels and engine output control, the TRC helps minimize the slippage of the drive wheels, thus generating the drive force that is appropriate for the road surface conditions.


ii.

For example, a comparison may be made between two vehicles, one with the TRC and the other without. In the vehicle without the TRC, if the accelerator pedal is operated in a rough manner while driving over a surface with different surface friction characteristics, the drive wheel on the slippery surface could slip as illustrated. As a result, the vehicle could become unstable.

However, in the vehicle with the TRC, the skid control ECU instantly determines the state of the vehicle and operates the brake actuator in order to apply to the slipping drive wheel. Furthermore, the engine ECU receives the signals from the skid control ECU and regulates the engine output. Thus, the function can constantly maintain a stable vehicle posture.

X135979E01
3.406,0.896 3.656,0.313 3.656,0.313 3.906,0.313 true 4.542,1.25 4.792,0.667 4.792,0.667 5.042,0.667 true 4.938,3.104 5.188,2.521 5.188,2.521 5.438,2.521 true 4.906,3.865 5.542,4.135 5.542,4.135 5.792,4.135 true 4.656,3.552 5.51,3.125 5.51,3.125 5.76,3.125 true 2.927,4.635 3.177,4.635 3.177,4.635 4.177,4.219 true 2.896,3.427 3.146,3.427 3.146,3.427 4.156,3.563 true 3.979,0.229 5.104,0.479 1.125,0.25 10 false Slippery Surface 5.115,0.583 6.24,0.833 1.125,0.25 10 false Slippery Surface 0.708,2.469 1.833,2.719 1.125,0.25 10 false Without TRC 2.042,2.99 2.854,3.25 0.813,0.26 10 false With TRC 1.479,3.354 3.063,3.625 1.583,0.271 10 false Engine Output Control 2.125,4.563 3.25,4.813 1.125,0.25 10 false Engine ECU 5.51,2.438 6.635,2.688 1.125,0.25 10 false Slippery Surface 5.833,3.042 7.063,3.708 1.229,0.667 10 false Brake Actuator with Skid Control ECU 5.865,4.052 7,4.604 1.135,0.552 10 false Brake the Slipping Drive Wheel



f.

Outline of VSC

i.

General

1.

The followings are two examples that can be considered as circumstances in which the tires exceed their lateral grip limit.

The VSC is designed to help control the vehicle behavior by controlling the engine output and the brakes at each wheel when the vehicle is under one of the conditions indicated below.

-

When the front wheels lose grip in relation to the rear wheels (front wheel skid tendency).

-

When the rear wheels lose grip in relation to the front wheels (rear wheel skid tendency).

X136199E01
1.188,2.438 3.125,2.771 1.938,0.333 10 false Front Wheel Skid Tendency 4.563,2.417 6.521,2.792 1.958,0.375 10 false Rear Wheel Skid Tendency




ii.

Method for Determining the Vehicle Condition

1.

To determine the condition of the vehicle, sensors detect the steering angle, vehicle speed, vehicle's yaw rate, and vehicle's lateral acceleration, which are then calculated by the skid control ECU.

(a)

Determining Front Wheel Skid

Whether the vehicle is in the state of the front wheel skid or not is determined by the difference between the target yaw rate and the vehicle's actual yaw rate.

When the vehicle's actual yaw rate is smaller than the yaw rate (a target yaw rate that is determined by the vehicle speed and steering angle) that should be rightfully generated when the driver operates the steering wheel, it means the vehicle is making a turn at a greater angle than the locus of travel.

Thus, the skid control ECU determines that there is a large tendency to front wheel skid.

X135963E01
2.594,0.042 5.427,0.281 2.833,0.24 10 false Actual Locus of Travel (Actual Yaw Rate) 4.448,0.615 6.219,1.49 1.771,0.875 10 false Locus of Travel Based on the Target Yaw Rate


(b)

Determining Rear Wheel Skid

Whether the vehicle is in the state of the rear wheel skid or not is determined by the values of the vehicle's slip angle and the vehicle's slip angular velocity (time-dependent changes in the vehicle's slip angle). When the vehicle's slip angle and the slip angular velocity are large, the skid control ECU determines that the vehicle has a large rear wheel skid tendency.

X135962E01
2.979,0.667 3.479,0.667 3.479,0.667 3.729,0.583 true 2.167,0.104 5.365,0.302 3.198,0.198 10 false Direction of Travel of the Vehicle's Center of Gravity 4.021,0.469 5.469,0.719 1.448,0.25 10 false Movement of Vehicle 2.302,0.583 3.167,0.917 0.865,0.333 10 false Slip Angle





iii.

Method for VSC Operation

1.

When the skid control ECU determines that the vehicle has a tendency to front wheel skid or rear wheel skid, it decreases the engine output and applies the brake of a front or rear wheel to control the vehicle's yaw moment.

The basic operation of the VSC is described below. However, the control method differs depending on the vehicle's characteristics and driving conditions.

(a)

Dampening a Front Wheel Skid

When the skid control ECU determines that there is a large front wheel skid tendency, it counteracts in accordance with the extent of that tendency. The skid control ECU controls the engine output and applies the brake to the rear wheel of the inner circle of the turn in order to help restrain the front wheel skid tendency.

Marking a Right Turn
X135952E01
3.417,2.083 3.667,2.417 3.667,2.417 3.917,2.417 true 3.979,2.333 5.667,2.531 1.688,0.198 10 false Brake Force 4.313,0.51 6,0.708 1.688,0.198 10 false Control Moment


(b)

Dampening a Rear Wheel Skid

When the skid control ECU determines that there is a large rear wheel skid tendency, it counteracts in accordance with the extent of that tendency. It applies the brakes of the front and rear wheels of the outer circle of the turn, and generates an outward moment of inertia in the vehicle, in order to help restrain the rear wheel skid tendency. Along with the reduction in the vehicle speed caused by the brake force, the excellent vehicle's stability is ensured.

In some cases, the skid control ECU applies the brake of the rear wheels as necessary.

Marking a Right Turn
X135953E01
2.75,0.75 3,0.75 3,0.75 3.417,1.083 true 2.25,1.583 2.5,1.583 2.5,1.583 2.917,1.917 true 3.25,0.198 4.542,0.427 1.292,0.229 10 false Control Moment 1.938,0.667 2.885,0.917 0.948,0.25 10 false Brake Force 1.448,1.51 2.396,1.76 0.948,0.25 10 false Brake Force






g.

Outline of Cooperative Control with EPS

i.

Braking when Surface Resistance Differs between Both Sides of Wheels

1.

If the driver suddenly applies the brakes on a road surface with a considerable difference in friction coefficient between the right and left wheels, the difference in the brake force between the right and left wheels will cause the vehicle posture to become unstable and create a yaw moment. In this state, the skid control ECU controls the VSC to stabilize the vehicle posture. At the same time, it effects cooperative control with the EPS to provide steering torque assist, which facilitates the driver's steering maneuvers to stabilize the vehicle posture.

X135889E01
3.594,1.438 4.677,0.688 4.677,0.688 5.01,0.688 true 3.948,1.646 4.698,1.229 4.698,1.229 5.031,1.229 true 3.938,2.76 4.688,2.344 4.688,2.344 5.021,2.344 true 2.135,2.99 2.469,2.99 2.469,2.99 3.219,2.74 true 2.208,2.219 2.542,2.219 2.542,2.219 3.458,1.802 true 2.208,1.052 2.542,1.052 2.542,1.052 3.208,1.469 true 2.781,3.583 3.031,3.583 3.031,3.583 3.198,3.25 true 4.052,3.25 4.135,3.583 4.135,3.583 4.385,3.583 true 5.104,2.26 6.49,2.531 1.385,0.271 10 false Brake Force 5.125,1.146 6.51,1.417 1.385,0.271 10 false Brake Force 1.313,2.896 2.698,3.167 1.385,0.271 10 false Brake Force 1.396,0.969 2.781,1.24 1.385,0.271 10 false Brake Force 0.927,2.125 2.167,2.594 1.24,0.469 10 false Yaw Moment during Brake Controlling 5.104,0.604 6.635,0.917 1.531,0.313 10 false Assisting Direction 4.469,3.5 5.854,3.771 1.385,0.271 10 false High μ Road 2.021,3.5 2.917,3.729 0.896,0.229 10 false Low μ Road



ii.

Accelerating when Surface Resistance Differs between Both Sides of Wheels

1.

If the driver suddenly starts off or accelerates on a road surface with a considerable difference in friction coefficient between the right and left wheels, the slippage of a drive wheel will cause the vehicle posture to become unstable and negatively affect its acceleration performance. In this state, the skid control ECU causes the TRC to control the hydraulic brake of the slipping drive wheel, and requests the engine ECU to effect engine output control. At the same time, it effects cooperative control with the EPS to provide steering torque assist, which facilitates the driver's steering maneuvers to stabilize the vehicle posture.

X135890E01
3.583,1.427 4.583,1.01 4.583,1.01 4.917,1.01 true 3.927,2.094 4.594,1.844 4.594,1.844 4.927,1.844 true 3.938,3.24 4.104,3.573 4.104,3.573 4.438,3.573 true 2.646,3.563 2.979,3.563 2.979,3.563 3.229,3.229 true 2.042,0.521 2.375,0.521 2.375,0.521 3.208,0.938 true 2.083,2.01 2.417,2.01 2.417,2.01 3.5,1.76 true 2.125,2.719 2.458,2.719 2.458,2.719 3.208,2.219 true 3.927,0.781 4.594,0.531 4.594,0.531 4.927,0.531 true 1.292,0.448 2.229,0.708 0.938,0.26 10 false Drive Force 5.01,0.448 5.948,0.708 0.938,0.26 10 false Drive Force 5.01,1.76 5.948,2.021 0.938,0.26 10 false Drive Force 1.385,2.635 2.323,2.896 0.938,0.26 10 false Drive Force 0.813,1.917 2.052,2.354 1.24,0.438 10 false Yaw Moment during Acceleration 5.031,0.927 6.552,1.25 1.521,0.323 10 false Assisting Direction 1.875,3.479 2.813,3.74 0.938,0.26 10 false Low μ Road 4.51,3.49 5.448,3.75 0.938,0.26 10 false High μ Road



iii.

Front Wheel Skid Tendency

1.

When the skid control ECU determines a front wheel skid tendency, it controls the VSC to dampen the front wheel skid. At the same time, it effects the cooperative control with the EPS to provide steering torque assists, which controls the driver's steering maneuvers to stabilize the vehicle posture. Steering torque assists are provided to inform the driver of the front wheel skid (a), and to prevent the driver's excessive turning of the steering wheel (b). In the assist for preventing excessive turning (b), it increases the resistance to counter the driver's steering effort, if the driver turns the steering wheel excessively.

X135951E01
4.302,2.396 4.969,2.396 true 1.198,0.063 2.583,0.948 1.385,0.885 10 false (a) Assisting Direction for Information of Front Wheel Skid 2.094,1.719 3.479,2.5 1.385,0.781 10 false (b) Assisting Direction for Preventing Excessive Turning 5.458,0.781 6.594,1.073 1.135,0.292 10 false Control Moment 5.042,2.313 6.177,2.604 1.135,0.292 10 false Brake Force



iv.

Rear Wheel Skid Tendency

1.

When the skid control ECU determines a rear wheel skid tendency, it controls the VSC to dampen the rear wheel skid. At the same time, it effects cooperative control with the EPS to provide steering torque assist, which facilitates the driver's steering maneuvers in the direction to correct the rear wheel skid.

X135888E01
3.583,0.438 3.917,0.438 3.917,0.438 4.25,0.854 true 4.438,0.052 5.708,0.302 1.271,0.25 10 false Control Moment 2.781,0.365 4.052,0.615 1.271,0.25 10 false Brake Force 2.469,1.677 3.094,2.146 0.625,0.469 10 false Assisting Direction




h.

Outline of Hill-start Assist Control Function

i.

When the vehicle starts off on a steep or slippery hill, it may start to descend backward while the driver switches from the brake pedal to the accelerator pedal, thus making it difficult for the vehicle to start off. To help prevent this from occurring, the hill-start assist control temporarily (approximately 2 seconds at the maximum) applies the brakes to all 4 wheels in order to help prevent the vehicle from descending backward.


ii.

Without the hill-start assist control, the driver must quickly and precisely switch from the brake pedal to the accelerator pedal. With the hill-start assist control, however, the driver can start off easily and operate the pedal in a relaxed manner, because the hill-start assist control helps prevent the vehicle from descending backward.

X136044E02
1.979,0.229 3.021,0.563 1.042,0.333 10 false Easy Control 5.406,0.24 6.542,0.552 1.135,0.313 10 false Difficult Control 0.927,3.458 2.917,3.688 1.99,0.229 10 false With Hill-start Assist Control 4.135,3.469 6.427,3.667 2.292,0.198 10 false Without Hill-start Assist Control


iii.

Hill-start assist control operates when all of the following conditions have been met:

Hill-start Assist Control Operation Condition
·

The shift lever is in any position other than P or N (climbing with the front or rear of the vehicle toward the hilltop).

·

The vehicle is at a standstill.

·

The accelerator pedal is not depressed.

·

The parking brake is released.




iv.

Hill-start assist control is canceled when any of the following conditions have been met:

Hill-start Assist Control Cancelation Condition
·

The shift lever is moved to P or N.

·

The accelerator pedal is depressed.

·

The parking brake is operated.

·

Approximately 2 seconds elapse since the operation started.






FUNCTION OF MAIN COMPONENTS


Component Function

*1: Only for Models with ABS, EBD, Brake Assist (Electrical Type), TRC, VSC and Cooperative Control with EPS

*2: Only for Models with ABS, EBD, and Brake Assist (Mechanical Type)

Combination Meter Brake System Warning Light
·

Lights up together with the ABS warning light to alert the driver when the skid control ECU detects a malfunction not only in the ABS but also in the EBD.

·

Lights up to alert the driver when the brake fluid level is low.

·

Lights up to inform the driver when the parking brake pedal is depressed.


ABS Warning Light Lights up to alert the driver when the skid control ECU detects a malfunction in the ABS.
VSC OFF Indicator Light*1 Lights up to inform the driver that the VSC system is turned off with the VSC OFF switch.
TRC OFF Indicator Light*1 Lights up to inform the driver that the TRC system is turned off with the VSC OFF switch.
Slip Indicator Light*1
·

Blinks to inform the driver that the TRC or VSC system is actuated.

·

Lights up to alert the driver when the skid control ECU detects a malfunction in the TRC or VSC system.


Steering Angle Sensor*1 Detects the direction and angle of the steering wheel.
Deceleration Sensor*2 Detects the vehicle's longitudinal and lateral acceleration and deceleration.
Yaw Rate & Deceleration Sensor*1
·

Detects the vehicle's yaw rate.

·

Detects the vehicle's longitudinal and lateral acceleration.


Speed Sensors Detect the wheel speed of each of 4 wheels.
VSC OFF Switch*1 Enables the driver to select "Normal mode", "TRC OFF mode", or "VSC OFF mode".
Stop Light Switch Detects the brake pedal depressing signal.
Parking Brake Switch Detects the parking brake pedal depressing signal.
Brake Pedal Load Sensing Switch*1 Detects the brake pedal load.
Brake Fluid Level Warning Switch Detects the brake fluid level.
Brake Booster
·

Increases the brake pedal effort.

·

(Operates the brake assist mechanism to mechanically activate the brake assist function.)*2


Brake Actuator Brake Actuator Changes the fluid path based on the signals from the skid control ECU during the operation of the brake control system functions, in order to control the fluid pressure that is applied to the wheel cylinders
Solenoid Relay Supply power to the solenoid valves.
Motor Relay Supplies power to the pump motor.
Master Cylinder Pressure Sensor*1 Assembled in the brake actuator, detects the master cylinder pressure.
Skid Control ECU Judges the vehicle driving condition based on the signals from each sensor, and sends the brake control signals to the brake actuator.
ECM
·

Sends the throttle position signal, accelerator pedal position signal, engine speed signal etc., to the skid control ECU.

·

(Based on the signals receives from the skid control ECU, controls the engine output.)*1


EPS ECU (Operates cooperatively with the skid control ECU to control the steering assist torque.)*1
Instrument Panel Junction Block Main Body ECU Detects the parking brake signal and outputs it to the skid control ECU via CAN communication.


FUNCTION


a.

VSC OFF Switch

i.

Using the VSC OFF switch can stop the operation of the VSC and TRC functions. This is used to stop engine output control and maintain drive torque when driving on the shoulder or on dirt roads.


ii.

The VSC OFF switch can be used to select 3 modes (Normal mode, TRC OFF mode or VSC OFF mode).


iii.

After the ignition switch is turned off in TRC OFF mode or VSC OFF mode, turning the ignition switch to ON again selects normal mode.

X136100E01
3.188,0.729 4.292,0.969 1.104,0.24 10 false Normal Mode 2.26,1.594 3.365,1.833 1.104,0.24 10 false TRC OFF Mode 3.979,1.594 5.083,1.833 1.104,0.24 10 false VSC OFF Mode 0.979,2.74 4.615,2.99 3.635,0.25 10 false : VSC OFF Switch Operation (Briefly Press). 0.979,3.073 5.552,3.354 4.573,0.281 10 false : VSC OFF Switch Operation (Press and Hold for 3 Seconds or More).


iv.

The operations of the brake control functions in each mode are as follows:

Mode Brake Control Function Combination Meter Assembly
TRC VSC TRC OFF Indicator Light VSC OFF Indicator Light

○: Applicable

-: Not applicable

*: Control will be performed during braking.

Normal Mode ○ ○ Does not illuminate Does not illuminate
TRC OFF Mode - ○ Illuminates Does not illuminate
VSC OFF Mode - -* Illuminates Illuminates




CONSTRUCTION


a.

Steering Angle Sensor (Only for Models with VSC)

i.

The steering angle sensor detects the steering direction and angle, and sends this signal to the skid control ECU.

X135980



b.

Yaw Rate and Deceleration Sensor

i.

Yaw Rate Sensor (Only for Models with VSC)

1.

The yaw rate sensor detects the vehicle's yaw rate. This sensor, which detects the vehicle's yaw rate, has a built-in deceleration sensor (yaw rate & deceleration sensor).



ii.

Deceleration Sensor

1.

The deceleration sensor detects the longitudinal acceleration and deceleration.

X136200E01
1.021,1.781 3.323,2.135 2.302,0.354 10 false Yaw Rate & Deceleration Sensor 1.052,4.219 2.635,4.521 1.583,0.302 10 false Deceleration Sensor 3.854,0.458 4.646,1.26 0.792,0.802 10 false Yaw Rate & Deceleration Sensor 3.865,2.76 4.656,3.323 0.792,0.563 10 false Deceleration Sensor 5.625,0.917 6.427,1.469 0.802,0.552 10 false Skid Control ECU 5.646,3.177 6.448,3.688 0.802,0.51 10 false Skid Control ECU 4.729,2.448 5.385,2.677 0.656,0.229 10 false VGS 4.729,2.75 5.198,3.01 0.469,0.26 10 false GL 4.719,3.042 5.26,3.281 0.542,0.24 10 false GGND




c.

Speed Sensor

i.

General

1.

An active type speed sensor is used. This sensor contains a Hall IC.

2.

The sensor rotor, which consists of N and S poles that are arranged in a circle, is integrated with the hub bearing inner race.

X136201E01
3.938,0.635 4.271,0.635 4.271,0.635 5.688,2.135 true 4.917,4.906 5.333,4.406 5.333,4.406 5.667,4.406 true 3.802,3.917 4.135,3.917 4.135,3.917 4.552,4.25 true 2,2.51 2.781,1.063 2.781,1.063 3.115,1.063 true 3.188,0.979 4.292,1.271 1.104,0.292 10 false Speed Sensor 3,0.563 4.104,0.854 1.104,0.292 10 false Speed Sensor 1.583,3.406 2.688,3.698 1.104,0.292 10 false Front Axle 5.125,3.365 6.229,3.656 1.104,0.292 10 false Rear Axle 2.885,3.844 3.99,4.135 1.104,0.292 10 false Speed Sensor 5.75,4.313 6.854,4.604 1.104,0.292 10 false Sensor Rotor 1.948,5.375 4.052,5.708 2.104,0.333 10 false N and S Poles Arrangement 2.427,4.583 2.604,4.823 0.177,0.24 10 false N 2.771,4.438 2.948,4.677 0.177,0.24 10 false N 2.583,4.49 2.76,4.729 0.177,0.24 10 false S 2.938,4.458 3.115,4.698 0.177,0.24 10 false S



ii.

Operation

1.

Along with the rotational movement of the sensor rotor, the N and S poles of the sensor rotor pass alternately near the sensing portion of the speed sensor. This speed sensor outputs magnetic flux as a current value. The skid control ECU detects the changes in the output current to determine the wheel speed.

2.

Unlike the passive type speed sensors used on conventional models that output analog pulses, the active type speed sensor outputs digital pulses. Therefore, it can start detecting vehicle speeds at approximately 0 km/h.

X136202E01
4.615,5.938 4.781,5.271 4.781,5.271 5.031,5.271 true 4.167,6.656 4.479,4.927 4.479,4.927 4.729,4.927 true 1.802,2.917 1.969,2.917 1.969,2.917 2.24,3.5 true 0.125,0.281 2.385,0.573 2.26,0.292 10 false Active Type Speed Sensor 2.802,1.292 3.375,1.604 0.573,0.313 10 false Hall IC 0.25,1.938 1.927,2.573 1.677,0.635 10 false Sensor Rotor (Hub Bearing Inner Race) 3.969,1.219 4.469,1.813 0.5,0.594 10 false Output Voltage 4.75,2 6.302,2.292 1.552,0.292 10 false Forward and Backward 6.167,1.719 6.615,1.948 0.448,0.229 10 false Time 0.115,2.5 2.323,3.052 2.208,0.552 10 false Passive Type Speed Sensor 0.281,4.156 1.854,4.708 1.573,0.552 10 false Sensor Rotor (Drive Shaft or Axle Shaft) 1.542,2.823 2.042,3.073 0.5,0.25 10 false Coil 2.625,3.385 3.188,3.74 0.563,0.354 10 false Magnet 4.271,2.813 4.563,3.063 0.292,0.25 10 false +V 4.302,4.021 4.594,4.281 0.292,0.26 10 false -V 4.802,4.188 6.427,4.448 1.625,0.26 10 false Forward and Backward 4.354,3.417 4.604,3.625 0.25,0.208 10 false 0 3.781,3.333 4.281,3.927 0.5,0.594 10 false Output Voltage 6.521,3.521 6.969,3.75 0.448,0.229 10 false Time 0.188,4.958 0.677,5.51 0.49,0.552 10 false Vehicle Speed 0.24,6.885 0.719,7.406 0.479,0.521 10 false Sensor Output 2.906,6.781 3.354,7.198 0.448,0.417 10 false Digital Output 1.542,7.479 2.427,7.781 0.885,0.302 10 false Active Type 3.5,4.99 3.99,5.542 0.49,0.552 10 false Vehicle Speed 3.51,6.563 3.99,7.083 0.479,0.521 10 false Sensor Output 6.479,6.563 6.958,7.208 0.479,0.646 10 false Analog Output 4.865,7.469 5.75,7.771 0.885,0.302 10 false Passive Type 5.104,5.188 5.99,5.49 0.885,0.302 10 false No Detecting 4.813,4.854 5.698,5.156 0.885,0.302 10 false No Detecting




d.

Brake Actuator

i.

General

1.

The brake actuator consists of the actuator portion, skid control ECU, solenoid relay and motor relay.

ABS and EBD Type
X136312E01
4.073,0.521 4.323,0.188 4.323,0.188 4.656,0.188 true 2.021,0.552 2.354,0.552 2.354,0.552 2.604,0.969 true 0.906,0.479 2.385,0.688 1.479,0.208 10 false Skid Control ECU 4.75,0.104 6.229,0.313 1.479,0.208 10 false Actuator Portion

ABS, EBD, Brake Assist, TRC, VSC and Hill-start Assist Control Type
X136101E01
4.563,0.833 5.146,0.5 5.146,0.5 5.479,0.5 true 1.552,0.688 1.885,0.688 1.885,0.688 2.302,0.938 true 5.573,0.427 6.958,0.729 1.385,0.302 10 false Actuator Portion 0.427,0.615 1.813,0.917 1.385,0.302 10 false Skid Control ECU



ii.

Actuator Portion

1.

ABS and EBD Type

The actuator portion consists of 8 two-position solenoid valves, 1 motor, 2 pumps, and 2 reservoirs. The 8 two-position solenoid valves consist of 4 pressure holding valves [(1), (2), (3), (4)] and 4 pressure reduction valves [(5), (6), (7), (8)].

Hydraulic Circuit
X135882E01
3.75,2.583 3.833,2.583 3.833,2.583 3.917,2.833 true 3.25,2.865 3.333,3.115 3.333,3.115 3.417,3.115 true 3.208,4.333 3.208,4.667 3.208,4.667 3.292,4.667 true 3.875,4.917 3.958,4.917 3.958,4.917 3.958,4.333 true 0.844,0.521 2.521,0.74 1.677,0.219 10 false From Master Cylinder 5.021,0.542 6.698,0.76 1.677,0.219 10 false From Master Cylinder 3.333,2.5 3.823,2.781 0.49,0.281 10 false Pump 0.875,5.083 1.615,5.365 0.74,0.281 10 false Front Left 2.115,5.083 2.854,5.365 0.74,0.281 10 false Rear Right 4.49,5.083 5.229,5.365 0.74,0.281 10 false Rear Left 5.688,5.104 6.427,5.385 0.74,0.281 10 false Front Right 1.208,2.531 1.563,2.781 0.354,0.25 10 false (1) 2.271,2.531 2.625,2.781 0.354,0.25 10 false (2) 4.75,2.521 5.104,2.771 0.354,0.25 10 false (3) 5.823,2.531 6.177,2.781 0.354,0.25 10 false (4) 1.198,3.635 1.552,3.885 0.354,0.25 10 false (5) 2.271,3.635 2.625,3.885 0.354,0.25 10 false (6) 4.76,3.635 5.115,3.885 0.354,0.25 10 false (7) 5.813,3.646 6.167,3.896 0.354,0.25 10 false (8) 3.479,3.031 3.969,3.313 0.49,0.281 10 false Pump 3.344,4.583 4.083,4.865 0.74,0.281 10 false Reservoir 3.281,4.833 4.021,5.115 0.74,0.281 10 false Reservoir


2.

ABS, EBD, Brake Assist, TRC and VSC Type

The actuator portion consists of 12 two-position solenoid valves, 1 motor, 2 pumps, 2 reservoirs, and 1 master cylinder pressure sensor.

The actuator portion consists of 12 two-position solenoid valves, 1 motor, 2 pumps, 2 reservoirs, and 1 master cylinder pressure sensor. The 12 two-position solenoid valves consist of 2 master cylinder cut solenoid valves [(1), (4)], 2 reservoir cut solenoid valves [(2), (3)], 4 pressure holding valves [(5), (6), (7), (8)] and 4 pressure reduction valves [(9), (10), (11), (12)].

X136103E01
5.073,2.031 5.406,2.031 true 3.083,3.75 3.417,3.75 3.417,3.75 3.25,5.417 true 4.031,3.75 3.781,3.75 3.781,3.75 3.948,5.417 true 3.885,7.083 3.969,7.083 3.969,7.083 3.969,6.833 true 3.333,7.417 3.25,7.417 3.25,7.417 3.25,6.833 true 3.198,0.594 4.063,1.052 0.865,0.458 10 false Brake Master Cylinder 1.271,1.5 3.677,1.781 2.406,0.281 10 false Brake Actuator Assembly 3,1.948 5.406,2.229 2.406,0.281 10 false Master Cylinder Pressure Sensor 1.24,3.5 1.5,3.76 0.26,0.26 10 false (1) 2.583,3.49 2.844,3.75 0.26,0.26 10 false (2) 4.5,3.49 4.76,3.75 0.26,0.26 10 false (3) 5.813,3.49 6.073,3.75 0.26,0.26 10 false (4) 1.5,5 1.76,5.26 0.26,0.26 10 false (5) 2.427,5 2.688,5.26 0.26,0.26 10 false (6) 4.625,5 4.885,5.26 0.26,0.26 10 false (7) 5.542,5.01 5.802,5.271 0.26,0.26 10 false (8) 1.5,6.188 1.76,6.448 0.26,0.26 10 false (9) 2.396,6.177 2.656,6.438 0.26,0.26 10 false (10) 4.594,6.177 4.854,6.438 0.26,0.26 10 false (11) 5.51,6.188 5.771,6.448 0.26,0.26 10 false (12) 3.396,7.323 4.052,7.552 0.656,0.229 10 false Reservoir 3.302,7 3.958,7.229 0.656,0.229 10 false Reservoir 1.229,7.458 1.927,7.688 0.698,0.229 10 false Rear Left 2.26,7.479 2.958,7.708 0.698,0.229 10 false Front Right 4.354,7.448 5.052,7.677 0.698,0.229 10 false Front Left 5.385,7.448 6.135,7.667 0.75,0.219 10 false Rear Right 4.083,3.667 4.74,3.896 0.656,0.229 10 false Pump 2.677,3.667 3.333,3.896 0.656,0.229 10 false Pump






OPERATION


a.

ABS and EBD Operation

i.

Based on the signals received from the 4 speed sensors, the skid control ECU calculates each wheel speed and deceleration, and checks wheel slipping conditions. According to the slipping condition, the skid control ECU controls the pressure holding valve and pressure reduction valve in order to adjust the fluid pressure of the each wheel cylinder in the following 3 modes: pressure reduction, pressure holding, and pressure increase modes.

Not Activated Normal Braking - -
Activated Increase Mode Holding Mode Reduction Mode
Hydraulic Circuit
X135965E01
1.49,0.167 1.906,0.167 1.906,0.167 2.406,0.417 true 1.5,1.052 1.917,1.052 1.917,1.052 2.417,1.302 true 1.021,0.073 1.729,0.323 0.708,0.25 10 false Port A 1.063,0.958 1.771,1.208 0.708,0.25 10 false Port B 0.604,0.448 2.167,0.729 1.563,0.281 10 false Pressure Holding Valve 0.458,1.375 2.302,1.635 1.844,0.26 10 false Pressure Reduction Valve 2.177,1.844 3.427,2.094 1.25,0.25 10 false To Wheel Cylinder

X135966

X135967E01
0.469,0.958 2.333,1.271 1.865,0.313 10 false To Reservoir and Pump 1.969,1.833 3.427,2.135 1.458,0.302 10 false From Wheel Cylinder

Pressure Holding Valve (Port A) OFF (Open) ON (Close) ←
Pressure Reduction Valve (Port B) OFF (Close) ← ON (Open)
Wheel Cylinder Pressure Increase Hold Reduce



b.

Brake Assist Operation (Electrical Type)

i.

In the event of emergency braking, the skid control ECU detects the driver's intention based on the speed of the pressure increase in the master cylinder determined by the master cylinder pressure sensor signal. If the skid control ECU judges the need for additional brake assist, pressure is generated by the pump in the brake actuator and directed to the wheel cylinder to apply a greater fluid pressure than the master cylinder. Also in the following cases, the skid control ECU provides brake assist.

·

In the event of a brake booster failure, the skid control ECU detects the failure based on the data from the brake pedal load sensing switch and master cylinder pressure sensor.

System Diagram
X135929E01
3.875,0.25 4.969,0.479 1.094,0.229 10 false Brake Actuator 0.844,1.448 1.938,1.677 1.094,0.229 10 false Speed Sensors 0.719,2.313 1.938,2.583 1.219,0.271 10 false Stop Light Switch 0.688,3.167 1.781,3.708 1.094,0.542 10 false Brake Pedal Load Sensing Switch 2.708,2.042 3.51,2.469 0.802,0.427 10 false Skid Control ECU 3.958,0.792 5.052,1.021 1.094,0.229 10 false Motor Relay 4.01,1.604 4.583,2.01 0.573,0.406 10 false Solenoid Relay 5.458,0.792 6.552,1.021 1.094,0.229 10 false Pump Motor 5.302,1.323 6.469,1.542 1.167,0.219 10 false Solenoid Valve (8) 5.25,1.906 6.49,2.438 1.24,0.531 10 false Master Cylinder Cut Solenoid Valve (2) 5.135,2.542 6.531,3.073 1.396,0.531 10 false Reservoir Cut Solenoid Valve (2) 5.313,3.208 6.375,3.573 1.063,0.365 10 false Master Cylinder Pressure Sensor 0.979,4.708 2.073,4.938 1.094,0.229 10 false Brake Actuator 0.958,5.094 2.052,5.323 1.094,0.229 10 false Brake Actuator 4.177,6.177 6.74,6.594 2.563,0.417 10 false : CAN (Controller Area Network)

Brake Assist Operation
X135930E01
2.104,0.792 2.385,0.313 2.385,0.313 2.635,0.313 true 3.198,3.198 3.365,4.531 3.365,4.531 3.448,4.531 true 3.75,4.115 3.833,4.115 3.833,4.115 3.969,3.188 true 3.896,5.208 3.979,5.208 3.979,5.208 3.979,4.958 true 3.198,4.969 3.198,5.49 3.198,5.49 3.281,5.49 true 0.885,1.115 0.969,1.115 0.969,1.115 1.552,1.531 true 0.854,2.521 0.938,2.521 0.938,2.521 1.771,2.854 true 0.875,3.563 0.958,3.563 0.958,3.563 1.792,3.896 true 2.542,1.281 2.625,1.281 2.625,1.281 2.792,1.531 true 4.396,1.531 4.5,1.26 4.5,1.26 4.583,1.26 true 2.198,4.719 2.281,4.719 2.281,4.719 2.615,3.885 true 5.635,1.531 6.219,1.281 6.219,1.281 6.302,1.281 true 5.396,2.865 6.229,2.448 6.229,2.448 6.313,2.448 true 5.396,3.896 6.229,3.646 6.229,3.646 6.313,3.646 true 4.552,3.896 4.802,4.729 4.802,4.729 4.885,4.729 true 2.635,2.875 2.729,2.302 2.729,2.302 2.813,2.302 true 4.385,2.271 4.469,2.271 4.469,2.271 4.542,2.875 true 0.802,0.135 2.208,0.365 1.406,0.229 10 false From Master Cylinder 5.094,0.146 6.5,0.375 1.406,0.229 10 false From Master Cylinder 2.729,0.229 5.063,0.438 2.333,0.208 10 false Master Cylinder Pressure Sensor 0.365,1.031 1,1.292 0.635,0.26 10 false Port (A) 2.052,1.188 2.688,1.448 0.635,0.26 10 false Port (B) 4.646,1.177 5.281,1.438 0.635,0.26 10 false Port (C) 6.385,1.208 7.021,1.469 0.635,0.26 10 false Port (D) 0.323,2.438 0.958,2.698 0.635,0.26 10 false Port (E) 2.854,2.208 3.49,2.469 0.635,0.26 10 false Port (F) 3.875,2.188 4.51,2.448 0.635,0.26 10 false Port (G) 6.396,2.375 7.031,2.635 0.635,0.26 10 false Port (H) 0.385,3.479 1.021,3.74 0.635,0.26 10 false Port (I) 1.698,4.625 2.333,4.885 0.635,0.26 10 false Port (J) 4.958,4.646 5.594,4.906 0.635,0.26 10 false Port (K) 6.406,3.563 7.042,3.823 0.635,0.26 10 false Port (L) 1.427,5.521 2.198,5.792 0.771,0.271 10 false Front Right 3.5,4.438 4.135,4.698 0.635,0.26 10 false Pump 3.302,5.115 3.938,5.375 0.635,0.26 10 false Reservoir 3.365,4.021 4,4.281 0.635,0.26 10 false Pump 3.333,5.406 3.969,5.667 0.635,0.26 10 false Reservoir 2.438,5.51 3.208,5.781 0.771,0.271 10 false Rear Left 4.188,5.531 4.958,5.802 0.771,0.271 10 false Rear Right 5.167,5.531 5.938,5.802 0.771,0.271 10 false Front Left 1.51,2.042 1.813,2.281 0.302,0.24 10 false (1) 2.74,2.031 3.042,2.271 0.302,0.24 10 false (2) 4.323,2.042 4.625,2.281 0.302,0.24 10 false (3) 5.552,2.042 5.854,2.281 0.302,0.24 10 false (4) 1.719,3.365 2.021,3.604 0.302,0.24 10 false (5) 2.583,3.354 2.885,3.594 0.302,0.24 10 false (6) 4.5,3.365 4.802,3.604 0.302,0.24 10 false (7) 5.313,3.365 5.615,3.604 0.302,0.24 10 false (8) 1.729,4.396 2.031,4.635 0.302,0.24 10 false (9) 2.521,4.375 2.823,4.615 0.302,0.24 10 false (10) 4.458,4.375 4.76,4.615 0.302,0.24 10 false (11) 5.271,4.396 5.573,4.635 0.302,0.24 10 false (12)

Item Port Brake Assist Not Activated Brake Assist Activated
Master Cylinder Cut Solenoid Valves
(1), (4)
(A), (D) OFF (Open) ON (Close)
Reservoir Cut Solenoid Valves
(2), (3)
(B), (C) OFF (Close) ON (Open)
Pressure Holding Solenoid Valves
(5), (6), (7), (8)
(E), (F), (G), (H) OFF (Open) ←
Pressure Reduction Solenoid Valves
(9), (10), (11), (12)
(I), (J), (K), (L) OFF (Close) ←
Pump OFF ON




c.

TRC Operation

i.

The fluid pressure generated by the pump is regulated by the master cylinder cut solenoid valve to the required pressure. Thus, the wheel cylinders of the driver wheels are controlled in the following 3 modes: pressure reduction, pressure holding, and pressure increase modes to control the slippage of the drive wheels.

The diagram shows the hydraulic circuit in the pressure increase mode when the TRC is activated.

The pressure holding solenoid valve and the pressure reduction solenoid valve are turned ON/OFF according to the ABS and EBD operation pattern.

When the TRC is activated, each solenoid valve operates as shown in the table.

System Diagram
X135931E01
3.885,0.333 5.031,0.563 1.146,0.229 10 false Brake Actuator 0.802,1.635 1.948,1.865 1.146,0.229 10 false Speed Sensors 0.688,3.094 1.833,3.323 1.146,0.229 10 false Stop Light Switch 2.656,2.156 3.438,2.885 0.781,0.729 10 false Skid Control ECU 3.896,0.854 4.792,1.135 0.896,0.281 10 false Motor Relay 4,1.656 4.563,2.031 0.563,0.375 10 false Solenoid Relay 5.427,0.854 6.573,1.083 1.146,0.229 10 false Pump Motor 5.25,1.396 6.396,1.625 1.146,0.229 10 false Solenoid Valve (8) 5.177,1.958 6.427,2.51 1.25,0.552 10 false Master Cylinder Cut Solenoid Valve (2) 5.094,2.625 6.49,3.115 1.396,0.49 10 false Reservoir Cut Solenoid Valve (2) 5.271,3.271 6.344,3.865 1.073,0.594 10 false Master Cylinder Pressure Sensor 0.906,4.74 2.052,4.969 1.146,0.229 10 false Combination Meter 0.792,5.615 2.417,5.906 1.625,0.292 10 false TRC OFF Indicator Light 0.927,5.24 2.24,5.563 1.313,0.323 10 false Slip Indicator Light 0.854,6.292 2.427,6.583 1.573,0.292 10 false Steering Angle Sensor 0.75,6.885 2.323,7.25 1.573,0.365 10 false Yaw Rate & Deceleration Sensor 3.875,5.063 5.021,5.292 1.146,0.229 10 false Engine ECU 3.958,6.115 5.104,6.344 1.146,0.229 10 false EPS ECU 5.167,6.125 6.313,6.354 1.146,0.229 10 false EPS Motor 5.49,4.688 6.635,4.917 1.146,0.229 10 false Throttle Body 5.323,5.042 6.844,5.344 1.521,0.302 8 false Throttle Position Sensor 5.302,5.365 6.563,5.552 1.26,0.188 9 false Throttle Control Motor 4.167,7.188 6.708,7.479 2.542,0.292 10 false : CAN (Controller Area Network)

TRC Operation
X135932E01
2.083,0.75 2.417,0.333 2.417,0.333 2.583,0.333 true 2.083,0.75 2.417,0.333 2.417,0.333 2.583,0.333 true 3.198,3.208 3.354,4.323 3.354,4.323 3.438,4.323 true 3.198,4.948 3.198,5.615 3.198,5.615 3.281,5.615 true 3.74,4.042 3.823,4.042 3.823,4.042 3.979,3.208 true 3.885,5.292 3.969,5.292 3.969,5.292 3.969,4.958 true 0.875,1.365 0.958,1.365 0.958,1.365 1.542,1.531 true 0.865,2.625 0.948,2.625 0.948,2.625 1.781,2.875 true 0.865,3.646 0.948,3.646 0.948,3.646 1.781,3.896 true 4.406,2.271 4.49,2.271 4.49,2.271 4.552,2.865 true 2.281,4.74 2.365,4.74 2.365,4.74 2.615,3.906 true 2.573,1.25 2.656,1.25 2.656,1.25 2.781,1.542 true 4.385,1.542 4.49,1.25 4.49,1.25 4.573,1.25 true 5.625,1.531 6.156,1.344 6.156,1.344 6.24,1.344 true 5.385,2.875 6.24,2.667 6.24,2.667 6.323,2.667 true 5.396,3.896 6.229,3.729 6.229,3.729 6.313,3.729 true 4.552,3.896 4.802,4.729 4.802,4.729 4.885,4.729 true 2.635,2.865 2.667,2.281 2.667,2.281 2.75,2.281 true 0.813,0.135 2.219,0.417 1.406,0.281 10 false From Master Cylinder 5.104,0.115 6.51,0.396 1.406,0.281 10 false From Master Cylinder 2.656,0.25 4.74,0.615 2.083,0.365 10 false Master Cylinder Pressure Sensor 1.49,2.042 1.74,2.292 0.25,0.25 10 false (1) 3.51,4.24 4.115,4.469 0.604,0.229 10 false Pump 3.354,3.948 3.958,4.177 0.604,0.229 10 false Pump 3.292,5.219 3.969,5.51 0.677,0.292 10 false Reservoir 3.354,5.531 4.031,5.823 0.677,0.292 10 false Reservoir 2.073,1.167 2.677,1.396 0.604,0.229 10 false Port (B) 4.625,1.167 5.229,1.396 0.604,0.229 10 false Port (C) 6.313,1.271 6.917,1.5 0.604,0.229 10 false Port (D) 0.333,2.542 0.938,2.771 0.604,0.229 10 false Port (E) 2.802,2.198 3.406,2.427 0.604,0.229 10 false Port (F) 3.885,2.188 4.49,2.417 0.604,0.229 10 false Port (G) 6.396,2.594 7,2.823 0.604,0.229 10 false Port (H) 0.396,3.563 1,3.792 0.604,0.229 10 false Port (I) 1.813,4.635 2.417,4.865 0.604,0.229 10 false Port (J) 4.938,4.646 5.542,4.875 0.604,0.229 10 false Port (K) 6.385,3.656 6.99,3.885 0.604,0.229 10 false Port (L) 1.396,5.573 2.333,5.823 0.938,0.25 10 false Front Right 2.448,5.573 3.385,5.823 0.938,0.25 10 false Rear Left 4.146,5.573 5.083,5.823 0.938,0.25 10 false Rear Right 5.188,5.573 6.125,5.823 0.938,0.25 10 false Front Left 2.729,2.031 2.979,2.281 0.25,0.25 10 false (2) 0.344,1.271 0.948,1.5 0.604,0.229 10 false Port (A) 4.302,2.031 4.552,2.281 0.25,0.25 10 false (3) 5.542,2.042 5.792,2.292 0.25,0.25 10 false (4) 1.719,3.365 1.969,3.615 0.25,0.25 10 false (5) 2.552,3.354 2.802,3.604 0.25,0.25 10 false (6) 4.479,3.365 4.729,3.615 0.25,0.25 10 false (7) 5.313,3.375 5.563,3.625 0.25,0.25 10 false (8) 1.719,4.396 1.969,4.646 0.25,0.25 10 false (9) 2.51,4.375 2.76,4.625 0.25,0.25 10 false (10) 4.438,4.375 4.688,4.625 0.25,0.25 10 false (11) 5.271,4.396 5.521,4.646 0.25,0.25 10 false (12)

Item Port TRC Not Activated TRC Activated
Increase Mode Holding Mode Reduction Mode
Master Cylinder Cut Solenoid Valves
(1), (4)
(A), (D) OFF (Open) ON (Close) ← OFF (Open)
Reservoir Cut Solenoid Valves
(2), (3)
(B), (C) OFF (Close) ON (Open) OFF (Close) ←
Front Brake Pressure Holding Solenoid Valves
(5), (8)
(E), (H) OFF (Open) ← ← ←
Pressure Reduction Solenoid Valves
(9), (12)
(I), (L) OFF (Close) ← ← ←
Wheel Cylinder Pressure Right - - Increase Hold Reduce
Left - - Increase Hold Reduce
Rear Brake Pressure Holding Solenoid Valves
(6), (7)
(F), (G) OFF (Open) ON (Close) ← ←
Pressure Reduction Solenoid Valves
(10), (11)
(J), (K) OFF (Close) ← ← ←
Wheel Cylinder Pressure Right - - - - -
Left - - - - -
Pump OFF ON ← ←



d.

VSC Operation

i.

General

1.

The VSC, by way of solenoid valves, controls the fluid pressure that is generated by the pump and applies it to the brake wheel cylinder of each wheel in the following 3 modes: pressure reduction, pressure holding, and pressure increase modes. As a result, the tendency to front wheel skid or rear wheel skid is controlled.

System Diagram
X135933E01
4.063,0.313 5.083,0.573 1.021,0.26 10 false Brake Actuator 0.781,1.375 1.979,1.698 1.198,0.323 10 false Speed Sensors 0.646,2.375 1.927,2.74 1.281,0.365 10 false Stop Light Switch 0.406,3.375 1.99,3.677 1.583,0.302 10 false VSC Warning Buzzer 2.656,2.021 3.448,2.688 0.792,0.667 10 false Skid Control ECU 3.875,0.833 4.708,1.167 0.833,0.333 10 false Motor Relay 3.979,1.656 4.542,2.198 0.563,0.542 10 false Solenoid Relay 5.406,0.865 6.427,1.125 1.021,0.26 10 false Pump Motor 5.25,1.396 6.51,1.75 1.26,0.354 10 false Solenoid Valve (8) 5.188,1.948 6.427,2.438 1.24,0.49 10 false Master Cylinder Cut Solenoid Valve (2) 5.094,2.604 6.5,3.052 1.406,0.448 10 false Reservoir Cut Solenoid Valve (2) 5.302,3.292 6.354,3.771 1.052,0.479 10 false Master Cylinder Pressure Sensor 5.51,4.698 6.531,4.958 1.021,0.26 10 false Throttle Body 5.302,5.042 6.604,5.365 1.302,0.323 8 false Throttle Position Sensor 5.302,5.365 6.625,5.625 1.323,0.26 9 false Throttle Control Motor 3.844,5.073 4.865,5.333 1.021,0.26 10 false Engine ECU 3.948,6.125 4.969,6.385 1.021,0.26 10 false EPS ECU 5.167,6.135 6.188,6.396 1.021,0.26 10 false EPS Motor 0.906,4.74 2.208,5.063 1.302,0.323 10 false Combination Meter 0.74,5.229 2.417,5.479 1.677,0.25 10 false VSC OFF Indicator Light 0.948,5.625 2.656,5.875 1.708,0.25 10 false Slip Indicator Light 0.854,6.292 2.417,6.625 1.563,0.333 10 false Steering Angle Sensor 0.75,6.875 2.333,7.344 1.583,0.469 10 false Yaw Rate & Deceleration Sensor 4.177,7.188 6.229,7.51 2.052,0.323 10 false : CAN (Controller Area Network)



ii.

Front Wheel Skid Restraining Control (Making a Right Turn)

1.

In the front wheel skid restraining control, the brake of the rear wheel of the inner circle of the turn is applied. Also, depending on whether the brake is ON or OFF and the condition of the vehicle, there are circumstances in which the brake might not be applied to the wheels even if those wheels are targeted for braking.

The diagram below shows the hydraulic circuit in the pressure increase mode, as it controls the front wheel skid condition while the vehicle makes a right turn.

In other operating mode, the pressure holding valve and the pressure reduction valve are turned ON/OFF according to the ABS and EBD operation pattern.

VSC Operation (Front Wheel Skid Restraining)
X135954E01
2.073,0.781 2.531,0.417 2.531,0.417 2.781,0.417 true 5.625,1.552 6.208,1.385 6.208,1.385 6.292,1.385 true 5.385,3.906 6.219,3.656 6.219,3.656 6.302,3.656 true 5.385,2.885 6.219,2.635 6.219,2.635 6.302,2.635 true 4.573,3.906 4.948,4.813 4.948,4.813 5.031,4.813 true 3.208,4.979 3.208,5.563 3.208,5.563 3.292,5.563 true 3.885,5.208 3.969,5.208 3.969,5.208 3.969,4.958 true 3.781,4.115 3.865,4.115 3.865,4.115 3.979,3.208 true 3.229,3.219 3.333,4.552 3.333,4.552 3.417,4.552 true 0.802,1.302 0.885,1.302 0.885,1.302 1.552,1.552 true 0.792,2.542 0.875,2.542 0.875,2.542 1.792,2.875 true 0.792,3.583 0.875,3.583 0.875,3.583 1.792,3.917 true 2.573,1.25 2.656,1.25 2.656,1.25 2.781,1.552 true 4.375,2.271 4.458,2.271 4.458,2.271 4.531,2.875 true 4.385,1.531 4.521,1.292 4.521,1.292 4.604,1.292 true 2.635,2.875 2.719,2.292 2.719,2.292 2.802,2.292 true 2.083,4.823 2.167,4.823 2.167,4.823 2.615,3.896 true 0.75,0.125 2.271,0.354 1.521,0.229 10 false From Master Cylinder 5.042,0.125 6.563,0.354 1.521,0.229 10 false From Master Cylinder 2.854,0.344 4.99,0.625 2.135,0.281 10 false Master Cylinder Pressure Sensor 0.271,1.219 0.885,1.563 0.615,0.344 10 false Port (A) 2.063,1.167 2.677,1.51 0.615,0.344 10 false Port (B) 4.656,1.208 5.271,1.552 0.615,0.344 10 false Port (C) 6.354,1.313 6.969,1.656 0.615,0.344 10 false Port (D) 0.26,2.458 0.875,2.802 0.615,0.344 10 false Port (E) 2.865,2.198 3.479,2.542 0.615,0.344 10 false Port (F) 3.875,2.188 4.49,2.531 0.615,0.344 10 false Port (G) 6.385,2.563 7,2.906 0.615,0.344 10 false Port (H) 0.313,3.5 0.927,3.844 0.615,0.344 10 false Port (I) 5.104,4.74 5.719,5.083 0.615,0.344 10 false Port (K) 6.385,3.573 7,3.917 0.615,0.344 10 false Port (L) 1.594,4.74 2.208,5.083 0.615,0.344 10 false Port (J) 1.365,5.573 2.188,5.781 0.823,0.208 10 false Front Right 2.427,5.573 3.25,5.781 0.823,0.208 10 false Rear Left 4.094,5.573 4.917,5.781 0.823,0.208 10 false Rear Right 5.177,5.583 6,5.792 0.823,0.208 10 false Front Left 3.333,5.469 4.156,5.677 0.823,0.208 10 false Reservoir 3.302,5.125 4.125,5.333 0.823,0.208 10 false Reservoir 3.479,4.469 4.031,4.74 0.552,0.271 10 false Pump 3.375,4.021 3.927,4.292 0.552,0.271 10 false Pump 1.5,2.052 1.906,2.271 0.406,0.219 10 false (1) 2.74,2.042 3.146,2.26 0.406,0.219 10 false (2) 4.323,2.042 4.729,2.26 0.406,0.219 10 false (3) 5.542,2.052 5.948,2.271 0.406,0.219 10 false (4) 1.729,3.375 2.135,3.594 0.406,0.219 10 false (5) 2.563,3.385 2.969,3.604 0.406,0.219 10 false (6) 4.479,3.375 4.885,3.594 0.406,0.219 10 false (7) 5.313,3.375 5.719,3.594 0.406,0.219 10 false (8) 1.74,4.417 2.146,4.635 0.406,0.219 10 false (9) 2.521,4.375 2.927,4.594 0.406,0.219 10 false (10) 4.448,4.385 4.854,4.604 0.406,0.219 10 false (11) 5.271,4.406 5.677,4.625 0.406,0.219 10 false (12)

Item Port VSC Not Activated VSC Activated
Increase Mode Holding Mode Reduction Mode
Master Cylinder Cut Solenoid Valves
(1), (4)
(A), (D) OFF (Open) ON (Close) ← ←
Reservoir Cut Solenoid Valves
(2), (3)
(B), (C) OFF (Close) ON (Open) ← ←
Front Brake Pressure Holding Solenoid Valves
(5), (8)
(E) OFF (Open) ON (Close) ← ←
(H) OFF (Open) ON (Close) ← ←
Pressure Reduction Solenoid Valves
(9), (12)
(I) OFF (Close) ← ← ON (Open)
(L) OFF (Close) ← ← ON (Open)
Wheel Cylinder Pressure Right - - - - -
Left - - - - -
Rear Brake Pressure Holding Solenoid Valves
(6), (7)
(F) OFF (Open) ON (Close) ← ←
(G) OFF (Open) ← ON (Close) ←
Pressure Reduction Solenoid Valves
(10), (11)
(J) OFF (Close) ← ← ON (Open)
(K) OFF (Close) ← ← ON (Open)
Wheel Cylinder Pressure Right - - Increase Hold Reduce
Left - - - - -
Pump OFF ON ← ←



iii.

Rear Wheel Skid Restraining Control (Making a Right Turn)

1.

In the rear wheel skid restraining control, the brakes of the front and rear wheels of the outer circle of the turn are applied. Also, depending on whether the brake is ON or OFF and the condition of the vehicle, there are circumstances in which the brake might not be applied to the wheels even if those wheels are targeted for braking.

The diagram below shows the hydraulic circuit in the pressure increase mode, as it controls the rear wheel skid condition while the vehicle makes a right turn.

In other operating mode, the pressure holding valve and the pressure reduction valve are turned ON/OFF according to the ABS and EBD operation pattern.

When the rear wheel skid restraining control is activated, each solenoid valve operates as shown in the table.

VSC Operation (Rear Wheel Skid Restraining)
X135955E01
2.146,0.802 2.49,0.375 2.49,0.375 2.74,0.375 true 5.635,1.542 6.302,1.208 6.302,1.208 6.385,1.208 true 5.396,2.875 6.313,2.625 6.313,2.625 6.396,2.625 true 5.396,3.917 6.313,3.667 6.313,3.667 6.396,3.667 true 4.563,3.896 4.813,4.813 4.813,4.813 4.896,4.813 true 2.625,2.865 2.708,2.281 2.708,2.281 2.792,2.281 true 4.406,1.542 4.5,1.25 4.5,1.25 4.583,1.25 true 2.583,1.25 2.667,1.25 2.667,1.25 2.792,1.542 true 0.885,1.292 0.969,1.292 0.969,1.292 1.552,1.542 true 0.781,2.635 0.865,2.635 0.865,2.635 1.781,2.885 true 0.781,3.656 0.865,3.656 0.865,3.656 1.781,3.906 true 2.104,4.823 2.188,4.823 2.188,4.823 2.604,3.906 true 3.75,4.083 3.833,4.083 3.833,4.083 4,3.198 true 3.896,5.219 3.979,5.219 3.979,5.219 3.979,4.969 true 3.208,4.958 3.208,5.542 3.208,5.542 3.292,5.542 true 3.208,3.219 3.333,4.5 3.333,4.5 3.417,4.5 true 4.406,2.281 4.49,2.281 4.49,2.281 4.552,2.875 true 0.771,0.146 2.313,0.354 1.542,0.208 10 false From Master Cylinder 5.083,0.135 6.625,0.344 1.542,0.208 10 false From Master Cylinder 2.823,0.292 5.125,0.573 2.302,0.281 10 false Master Cylinder Pressure Sensor 0.344,1.198 0.979,1.448 0.635,0.25 10 false Port (A) 2.083,1.167 2.719,1.417 0.635,0.25 10 false Port (B) 4.646,1.167 5.281,1.417 0.635,0.25 10 false Port (C) 6.448,1.135 7.083,1.385 0.635,0.25 10 false Port (D) 0.26,2.552 0.896,2.802 0.635,0.25 10 false Port (E) 2.833,2.198 3.469,2.448 0.635,0.25 10 false Port (F) 3.896,2.198 4.531,2.448 0.635,0.25 10 false Port (G) 6.458,2.542 7.094,2.792 0.635,0.25 10 false Port (H) 0.313,3.573 0.948,3.823 0.635,0.25 10 false Port (I) 1.635,4.729 2.271,4.979 0.635,0.25 10 false Port (J) 4.948,4.729 5.583,4.979 0.635,0.25 10 false Port (K) 6.469,3.594 7.104,3.844 0.635,0.25 10 false Port (L) 3.354,5.448 4.104,5.667 0.75,0.219 10 false Reservoir 3.323,5.135 4.073,5.354 0.75,0.219 10 false Reservoir 3.458,4.417 4,4.667 0.542,0.25 10 false Pump 3.354,4 3.844,4.26 0.49,0.26 10 false Pump 1.427,5.573 2.281,5.823 0.854,0.25 10 false Front Right 2.448,5.573 3.302,5.823 0.854,0.25 10 false Rear Left 4.167,5.563 5.021,5.813 0.854,0.25 10 false Rear Right 5.156,5.552 6.01,5.802 0.854,0.25 10 false Front Left 1.5,2.052 1.813,2.25 0.313,0.198 10 false (1) 2.729,2.042 3.042,2.24 0.313,0.198 10 false (2) 4.323,2.042 4.635,2.24 0.313,0.198 10 false (3) 5.563,2.042 5.875,2.24 0.313,0.198 10 false (4) 1.74,3.365 2.052,3.563 0.313,0.198 10 false (5) 2.563,3.365 2.875,3.563 0.313,0.198 10 false (6) 4.479,3.365 4.792,3.563 0.313,0.198 10 false (7) 5.313,3.375 5.625,3.573 0.313,0.198 10 false (8) 1.729,4.406 2.042,4.604 0.313,0.198 10 false (9) 2.521,4.385 2.833,4.583 0.313,0.198 10 false (10) 4.448,4.385 4.76,4.583 0.313,0.198 10 false (11) 5.271,4.406 5.583,4.604 0.313,0.198 10 false (12)

Item Port VSC Not Activated VSC Activated
Increase Mode Holding Mode Reduction Mode
Master Cylinder Cut Solenoid Valves
(1), (4)
(A) OFF (Open) ON (Close) ← ←
(D) OFF (Open) ON (Close) ← ←
Reservoir Cut Solenoid Valves
(2), (3)
(B) OFF (Close) ON (Open) ← ←
(C) OFF (Close) ON (Open) ← ←
Front Brake Pressure Holding Solenoid Valves
(5), (8)
(E) OFF (Open) ON (Close) ← ←
(H) OFF (Open) ← ON (Close) ←
Pressure Reduction Solenoid Valves
(9), (12)
(I) OFF (Close) ← ← ←
(L) OFF (Close) ← ← ON (Open)
Wheel Cylinder Pressure Right - - - - -
Left - - Increase Hold Reduce
Rear Brake Pressure Holding Solenoid Valves
(6), (7)
(F) OFF (Open) ← ON (Close) ←
(G) OFF (Open) ON (Close) ← ←
Pressure Reduction Solenoid Valves
(10), (11)
(J) OFF (Close) ← ← ON (Open)
(K) OFF (Close) ← ← ←
Wheel Cylinder Pressure Right - - - - -
Left - - Increase Hold Reduce
Pump OFF ON ← ←



iv.

Cooperative Control with EPS Operation

1.

The operation of the solenoid valves under the cooperative control with EPS is the same as the TRC or VSC operation.




e.

Engine Output Control

i.

During the TRC or VSC operation, the skid control ECU outputs a engine output control signal to the engine ECU. Upon receiving this signal, the engine ECU effects throttle control to regulate the engine output.

X135964E01
0.188,0.875 1.667,1.531 1.479,0.656 10 false Vehicle Condition (Front Wheel Skid or Rear Wheel Skid Level) 0.719,2.344 1.729,2.708 1.01,0.365 10 false Engine Torque 0.333,3.594 1.688,4.292 1.354,0.698 10 false Brake Wheel Cylinder Fluid Pressure* 1.479,4.198 1.875,4.417 0.396,0.219 10 false Low 1.479,2.885 1.875,3.104 0.396,0.219 10 false Low 1.469,1.563 1.865,1.781 0.396,0.219 10 false Low 1.396,0.49 1.792,0.708 0.396,0.219 10 false High 1.448,1.802 1.844,2.021 0.396,0.219 10 false High 1.448,3.104 1.844,3.323 0.396,0.219 10 false High 5.469,1.604 5.865,1.823 0.396,0.219 10 false Time 5.469,2.927 5.865,3.146 0.396,0.219 10 false Time 5.479,4.24 5.875,4.458 0.396,0.219 10 false Time 2.24,0.313 2.458,0.563 0.219,0.25 10 false (a) 2.49,0.313 2.708,0.563 0.219,0.25 10 false (b) 4.188,0.323 4.406,0.573 0.219,0.25 10 false (c) 4.438,0.333 4.656,0.583 0.219,0.25 10 false (d) 5.052,0.052 6.927,0.26 1.875,0.208 10 false (a): Start of engine control 5.052,0.281 7.094,0.469 2.042,0.188 10 false (b): Start of brake control 5.052,0.51 6.896,0.76 1.844,0.25 10 false (c): Brake control completed 5.052,0.74 7.052,1 2,0.26 10 false (d): Engine control completed 0.167,4.51 5.99,4.75 5.823,0.24 10 false *: The wheel cylinder that activates varies depending on the condition of the vehicle.



f.

Initial Check

i.

After the ignition switch is turned ON*1 or the engine switch is selected in the IG-ON*2, and the vehicle attains an approximate speed of 6 km/h (4 mph) or more, the skid control ECU performs the initial check.The functions of each solenoid valve and pump motor in the brake actuator are checked in order.

HINT:
·

*1: Models without Smart Entry & Start System

·

*2: Models with Smart Entry & Start System





g.

Hill-start Assist Control Operation

i.

When hill-start assist control is operating, the skid control ECU holds the brake fluid pressure.


ii.

Based on the information provided by various sensors, switches, and the ECM, the skid control ECU determines whether to activate hill-start assist control.

System Diagram
X136105E01
1.177,1.26 2.271,1.531 1.094,0.271 10 false Speed Sensors 1.135,2.76 2.354,3.042 1.219,0.281 10 false Stop Light Switch 3.292,0.531 3.865,1.042 0.573,0.51 10 false Solenoid Relay 3.031,1.75 4.167,2.042 1.135,0.292 10 false Skid Control ECU 3.198,3.104 4.292,3.375 1.094,0.271 10 false Motor Relay 4.948,0.396 6.198,0.875 1.25,0.479 10 false Master Cylinder Cut Solenoid Valve (2) 4.854,1.073 6.26,1.5 1.406,0.427 10 false Reservoir Cut Solenoid Valve (2) 4.99,1.76 6.125,2.208 1.135,0.448 10 false Pressure Holding Solenoid Valve (4) 4.938,2.448 6.167,2.885 1.229,0.438 10 false Pressure Reduction Solenoid Valve (4) 5.167,3.094 6.26,3.365 1.094,0.271 10 false Pump Motor 5.031,3.552 6.094,4.063 1.063,0.51 10 false Master Cylinder Pressure Sensor 4.354,4.208 5.448,4.479 1.094,0.271 10 false Brake Actuator 1.125,4.833 2.292,5.125 1.167,0.292 10 false Main Body ECU 5.469,4.823 6.563,5.094 1.094,0.271 10 false ECM 1.146,5.875 2.24,6.146 1.094,0.271 10 false Yawrate Sensor 5.01,5.823 6.479,6.083 1.469,0.26 10 false Combination Meter 5.063,6.313 6.458,6.635 1.396,0.323 10 false Slip Indicator Light 1.792,6.427 4.031,6.667 2.24,0.24 10 false : CAN (Controller Area Network)

X136104E01
4.667,0.833 4.917,0.833 4.917,0.833 5.333,1.333 true 1.521,2.167 1.688,1.417 1.688,1.417 1.854,1.417 true 2.719,2.156 2.885,1.406 2.885,1.406 3.052,1.406 true 4.448,2.146 4.063,1.188 4.063,1.188 3.896,1.188 true 5.646,2.167 5.01,1.417 5.01,1.417 4.844,1.417 true 1.76,3.49 1.01,2.823 1.01,2.823 0.844,2.823 true 4.563,3.479 4.479,2.927 4.479,2.927 4.313,2.927 true 5.396,3.49 6.146,2.823 6.146,2.823 6.313,2.823 true 5.406,4.573 6.156,3.906 6.156,3.906 6.323,3.906 true 1.76,4.583 1.01,3.917 1.01,3.917 0.844,3.917 true 2.594,4.573 2.177,5.406 2.177,5.406 2.01,5.406 true 2.833,2.917 2.667,2.917 2.667,2.917 2.594,3.49 true 5.167,5.406 5,5.406 5,5.406 4.583,4.573 true 3.365,6.333 3.198,6.333 3.198,6.333 3.198,5.667 true 3.802,5.917 3.969,5.917 3.969,5.917 3.969,5.667 true 3.688,4.99 3.771,4.99 3.771,4.99 3.917,4.406 true 3.24,4.406 3.406,5.323 3.406,5.323 3.49,5.323 true 0.781,0.469 2.344,0.708 1.563,0.24 10 false From Master Cylinder 5.188,0.458 6.75,0.698 1.563,0.24 10 false From Master Cylinder 2.604,0.74 4.885,0.948 2.281,0.208 10 false Master Cylinder Pressure Sensor 1.927,1.333 2.531,1.573 0.604,0.24 10 false Port (A) 3.125,1.323 3.729,1.563 0.604,0.24 10 false Port (B) 3.385,1.104 3.99,1.344 0.604,0.24 10 false Port (C) 4.323,1.333 4.927,1.573 0.604,0.24 10 false Port (D) 0.302,2.74 0.906,2.979 0.604,0.24 10 false Port (E) 2.906,2.823 3.51,3.063 0.604,0.24 10 false Port (F) 3.771,2.823 4.375,3.063 0.604,0.24 10 false Port (G) 6.396,2.729 7,2.969 0.604,0.24 10 false Port (H) 0.354,3.833 0.958,4.073 0.604,0.24 10 false Port (I) 1.51,5.323 2.115,5.563 0.604,0.24 10 false Port (J) 5.219,5.323 5.823,5.563 0.604,0.24 10 false Port (K) 6.385,3.823 6.99,4.063 0.604,0.24 10 false Port (L) 1.365,6.281 2.177,6.5 0.813,0.219 10 false Front Right 3.417,6.25 4.104,6.5 0.688,0.25 8 false Reservoir 2.385,6.292 3.104,6.51 0.719,0.219 10 false Rear Left 4.198,6.292 5.052,6.573 0.854,0.281 10 false Rear Right 5.167,6.281 5.958,6.531 0.792,0.25 10 false Front Left 3.531,5.24 4.021,5.458 0.49,0.219 8 false Pump 3.406,4.917 3.896,5.135 0.49,0.219 8 false Pump 3.26,5.844 3.948,6.094 0.688,0.25 8 false Reservoir 1.458,2.667 1.813,2.938 0.354,0.271 10 false (1) 2.656,2.667 3.01,2.938 0.354,0.271 10 false (2) 4.385,2.667 4.74,2.938 0.354,0.271 10 false (3) 5.594,2.677 5.948,2.948 0.354,0.271 10 false (4) 1.698,4.01 2.052,4.281 0.354,0.271 10 false (5) 2.531,4.01 2.885,4.281 0.354,0.271 10 false (6) 4.51,4.031 4.865,4.302 0.354,0.271 10 false (7) 5.354,4.031 5.708,4.302 0.354,0.271 10 false (8) 1.698,5.104 2.052,5.375 0.354,0.271 10 false (9) 2.5,5.073 2.854,5.344 0.354,0.271 10 false (10) 4.469,5.073 4.823,5.344 0.354,0.271 10 false (11) 5.281,5.104 5.635,5.375 0.354,0.271 10 false (12)

Item Port Not Activated Hill-start Assist Control Activated
Holding Mode Reduction Mode

*: Hydraulic pressure is controlled by continuously cycling the solenoid valves between open and closed, according to the operating conditions.

Master Cylinder Cut Solenoid Valves (1), (4) (A), (D) OFF (Open) ON* ON*
Reservoir Cut Solenoid Valves (2), (3) (B), (C) OFF (Close) OFF (Close) OFF (Close)
Front Brakes Pressure Holding Solenoid Valves (5), (8) (E), (H) OFF (Open) OFF (Open) OFF (Open)
Pressure Reduction Solenoid Valves (9), (12) (I), (L) OFF (Close) OFF (Close) OFF (Close)
Brake Wheel Cylinder Pressure - - Hold Reduce
Rear Brakes Pressure Holding Solenoid Valves (6), (7) (F), (G) OFF (Open) OFF (Open) OFF (Open)
Pressure Reduction Solenoid Valves (10), (11) (J), (K) OFF (Close) OFF (Close) OFF (Close)
Brake Wheel Cylinder Pressure - - Hold Reduce
Pump OFF OFF OFF




DIAGNOSIS


a.

If the skid control ECU detects a malfunction in the brake control system, the ABS, brake system or VSC warning light that corresponds to the function in which the malfunction has been detected indicates or illuminates as indicated in the table below to alert the driver of the malfunction.

Models with ABS, EBD, Brake Assist (Mechanical Type)
Item ABS EBD ABS and EBD Skid Control ECU

○: Light ON

-: Light OFF

ABS Warning Light ○ ○ ○ ○
Brake System Warning Light - ○ ○ ○

Models with ABS, EBD, Brake Assist (Electrical Type), TRC, VSC and Cooperative Control with EPS
Item ABS EBD Brake Assist TRC VSC ABS and EBD Skid Control ECU

○: Light ON

-: Light OFF

ABS Warning Light ○ ○ ○ - - ○ ○
Brake System Warning Light - ○ - - - ○ -
VSC Warning Light ○ ○ ○ ○ ○ ○ ○


b.

At the same time, the DTCs (Diagnostic Trouble Codes) are stored in memory. The DTCs can be read by connecting an intelligent tester II, or by connecting the SST (09843-18040) to the TC and CG terminals of the DLC3, and observing the blinking of the ABS warning light (and VSC warning light)*.


c.

This system has a sensor signal check (test mode) function. This function is activated by connecting an intelligent tester II, or by connecting the SST (09843-18040) to the TS and CG terminals of the DLC3. This check function performs speed sensor check.


d.

If the skid control ECU detects a malfunction during a sensor signal check (test mode), it stores the DTCs in its memory. These DTCs can be read during a sensor check operation by connecting an intelligent tester II or by connecting the SST (09843-18040) to the TC and CG terminals of the DLC3 and observing the blinking of the ABS warning light (or the VSC warning light)*.

HINT:
·

For details of the DTCs that are stored in skid control ECU memory and the DTCs that are output through the sensor signal check functions, see the Previa/Tarago Repair Manual.

·

*: Only for Models with ABS, EBD, Brake Assist, TRC, VSC and Cooperative Control with EPS





FAIL-SAFE


a.

In the event of a malfunction in the ABS, skid control ECU prohibits the brake control system.


b.

In the event of a malfunction in the EBD, the brake system is operated as long as possible even if the ABS is prohibited. If the EBD control becomes impossible, the brake system warning light illuminates to inform the driver of that. In this case, the brake system is operated in the same condition as the brake system without the brake control system.


c.

The following fail-safe functions are provided on the models with ABS, EBD, Brake Assist (electrical type), TRC, VSC and Cooperative Control with EPS:

·

In the event of a malfunction in the TRC and/or VSC, skid control ECU prohibits the TRC and VSC operation.

·

If a communication malfunction occurs between the skid control ECU and the steering angle sensor, the yaw rate & deceleration sensor or engine ECU, the skid control ECU stops the TRC and VSC.

·

When the engine ECU detects the DTC, it will disable the TRC and VSC.