Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
NM24M0E _55 Steering _061447 POWER ASSIST SYSTEMS _0299864 POWER STEERING SYSTEM UN GENERAL/CONTROL/DETAILS F

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS


Component Function
Steering Column Torque Sensor Detects the twist of the torsion bar, calculates the torque that is applied to the torsion bar by changing it into an electrical signal, and outputs this signal to the EPS ECU.
Motor Generates power assist in accordance with a signal received from the EPS ECU.
Rotation Angle Sensor Outputs the rotation angle of the motor to the EPS ECU.
Reduction Mechanism Reduces the speed of the motor through the use of a worm gear and a wheel gear and transmits it to the column shaft.
EPS ECU Actuates the motor mounted on the steering column to provide power assist, based on the signals received from various sensors and vehicle speed.
Engine ECU Outputs the engine speed signal to EPS ECU.
Combination Meter In case of a malfunction in the system, turns ON the P/S warning light.
Skid Control ECU Outputs the vehicle speed signal to EPS ECU.


CONSTRUCTION


a.

Steering Column

i.

General

1.

A motor, reduction mechanism, and torque sensor are mounted on the steering column.

Top View
X135936

Cross Section
X135937



ii.

Motor

1.

A low inertia, low noise, and high power output motor is used.

2.

The motor consists of the rotor, stator, rotation angle sensor, and motor shaft.

3.

The torque that is generated by the motor is transmitted to the worm gear via the joint.

Then this torque is transmitted to the column shaft via the wheel gear.

4.

The rotation angle sensor consists of resolver sensor, which excel in reliability and durability. As a result, it ensures efficient EPS control.

X135938E01
1.75,0.333 2.083,0.333 2.083,0.333 2.5,0.75 true 1.417,1.563 1.75,1.563 1.75,1.563 2.75,1.063 true 2,2.302 2.333,2.302 2.333,2.302 2.583,1.802 true 2.833,2.594 3.167,2.594 3.167,2.594 3.5,1.802 true 4.667,2.177 4.833,2.51 4.833,2.51 5.167,2.51 true 4.417,1.667 4.667,0.917 4.667,0.917 5,0.917 true 3.813,1.625 4.313,0.542 4.313,0.542 4.646,0.542 true 0.979,0.26 1.875,0.552 0.896,0.292 10 false Wheel Gear 0.542,1.49 1.875,1.813 1.333,0.323 10 false Column Shaft 1.25,2.229 2.146,2.521 0.896,0.292 10 false Worm Gear 2.073,2.521 3.01,2.76 0.938,0.24 10 false Motor Shaft 4.708,0.458 6.333,0.76 1.625,0.302 10 false Rotation Angle Sensor 5.073,0.833 5.969,1.125 0.896,0.292 10 false Rotor 5.229,2.427 6.125,2.719 0.896,0.292 10 false Stator



iii.

Reduction Mechanism

1.

This mechanism reduces the speed of the motor via the worm gear and the wheel gear, and transmits it to the column shaft.

2.

The wheel gear is made of a high-strength, low-friction, and low-wear plastic material, to realize low noise and a lightweight construction.

3.

A worm gear supported by ball bearings is used. Also, a leaf spring is provided to ensure the optimal meshing of the gears at all times.

X135939E01
2.167,2.26 2.417,2.26 2.417,2.26 2.667,1.594 true 3.5,2.479 3.75,2.479 3.75,2.479 4.083,1.979 true 3.198,0.354 3.448,0.354 3.448,0.354 4.198,1.188 true 4.583,0.917 5.167,0.5 5.167,0.5 5.417,0.5 true 4.719,1.813 5.302,1.438 5.302,1.438 5.552,1.438 true 2.333,0.281 3.698,0.573 1.365,0.292 10 false Column Shaft 5.49,0.406 6.854,0.698 1.365,0.292 10 false Wheel Gear 5.635,1.365 7,1.656 1.365,0.292 10 false Ball Bearing 1.427,2.177 2.792,2.469 1.365,0.292 10 false Leaf Spring 2.75,2.406 4.115,2.698 1.365,0.292 10 false Worm Gear



iv.

Torque Sensor

1.

A type of torque sensor with Hall ICs is used. This makes it possible to shorten the axial length of the sensor, thus increasing the extent of contraction of the steering column with the energy absorbing mechanism.

2.

The torque sensor is built into the steering column. A multipole magnet is mounted to the input shaft, and a yoke is mounted to the output shaft. The input and output shafts are joined by the torsion bar. A magnetic convergence ring assembly is placed outside of the yoke.

3.

The magnetic convergence ring assembly contains two Hall ICs, which face opposite to each other. The system detects the steering direction in accordance with the direction of the magnetic flux that passes between the Hall ICs. Furthermore, the system detects the steering torque in accordance with the amount of change in the magnetic flux density based on the relative displacement of the multipole magnet and the yoke. The EPS ECU monitors the torque sensor signals that are output by the two Hall ICs to detect malfunctions.

X136206E01
1.25,0.417 1.5,0.417 1.5,0.417 1.833,0.844 true 4,0.823 4.25,0.823 4.25,0.823 4.635,1.594 true 2.51,2.292 2.396,2.833 2.396,2.833 2.146,2.833 true 2.583,1.75 2.833,1.333 2.833,1.333 3.083,1.333 true 3.917,2.375 4.167,2.375 4.167,2.375 4.333,1.719 true 5.167,1.552 5.583,0.635 5.583,0.635 5.833,0.635 true 5.583,1.635 5.833,1.052 5.833,1.052 6.083,1.052 true 5.188,1.885 5.771,2.385 5.771,2.385 6.021,2.385 true 5.167,2 5.75,2.667 5.75,2.667 6,2.667 true 0.969,3.781 1.219,3.781 1.219,3.781 1.615,4.01 true 2.333,4.333 2.677,3.823 2.677,3.823 2.844,3.823 true 3.573,4.802 3.823,4.802 3.823,4.802 4.49,4.146 true 4.969,4.99 5.448,5.531 5.448,5.531 5.698,5.531 true 0.844,0.344 1.615,0.542 0.771,0.198 10 false Motor 1.427,2.01 1.667,2.26 0.24,0.25 10 false A 0.719,2.75 2.146,3.219 1.427,0.469 10 false Magnetic Convergence Ring Assembly 3.135,1.24 3.854,1.708 0.719,0.469 10 false Reduction Mechanism 3.177,0.74 4.146,0.969 0.969,0.229 10 false Output Shaft 5.906,0.552 7.052,0.854 1.146,0.302 10 false Multipole Magnet 6.146,0.958 6.917,1.219 0.771,0.26 10 false Input Shaft 6.083,2.583 6.854,2.781 0.771,0.198 10 false Hall IC 3.292,2.01 3.531,2.26 0.24,0.25 10 false A 6.083,2.313 7.156,2.635 1.073,0.323 10 false Multipole Magnet 3.177,2.292 3.948,2.49 0.771,0.198 10 false Torsion Bar 4.396,2.719 5.677,2.979 1.281,0.26 10 false A-A Cross Section 0.583,3.708 1,3.969 0.417,0.26 10 false Yoke 2.917,3.74 3.5,4.448 0.583,0.708 10 false Multipole Magnet 3,4.719 3.667,4.917 0.667,0.198 10 false Hall IC 2 5.833,5.469 6.5,5.667 0.667,0.198 10 false Hall IC 1 1.458,5.604 2.542,5.938 1.083,0.333 10 false Torque Sensor 1.708,8.375 2.792,8.708 1.083,0.333 10 false Torque Sensor 1.573,6.802 1.844,7.219 0.271,0.417 10 false Hall IC 1 1.563,7.708 1.844,8.125 0.281,0.417 10 false Hall IC 2 4.771,7.333 5.854,7.667 1.083,0.333 10 false EPS ECU 3.781,6.427 4.281,6.677 0.5,0.25 10 false TRQV 3.792,6.813 4.375,7.063 0.583,0.25 10 false TRQ1 3.771,7.188 4.271,7.438 0.5,0.25 10 false TRQG 3.802,7.688 4.385,7.938 0.583,0.25 10 false TRQ2

(a)

Straightline Driving

If the vehicle is driven straight and the driver does not turn the steering wheel, the yoke is located in the center between the N and S poles of the multipole magnet. Thus, no magnetic flux passes between the Hall ICs. In this case, the Hall ICs output a specified voltage to the EPS ECU, to indicate that the steering wheel is in the neutral position. Therefore, it does not apply current to the motor.

X135956E01
1.667,0.333 1.917,0.333 1.917,0.333 2.49,1.083 true 4.885,1.667 5.385,2.417 5.385,2.417 5.719,2.417 true 1.302,0.26 1.917,0.458 0.615,0.198 10 false Yoke 5.802,2.333 7,2.625 1.198,0.292 10 false Multipole Magnet 1.656,1.354 2.271,1.552 0.615,0.198 8 false Hall IC 2 5.125,1.333 5.74,1.531 0.615,0.198 8 false Hall IC 1 2.26,1.313 2.385,1.51 0.125,0.198 10 true N 3.531,1.302 3.656,1.5 0.125,0.198 10 true N 4.813,1.302 4.938,1.5 0.125,0.198 10 true N 2.833,1.302 2.958,1.5 0.125,0.198 10 true S 4.24,1.302 4.365,1.5 0.125,0.198 10 true S


(b)

When Steering

When a driver turns the steering wheel to the right or left, the twist that is created in the torsion bar creates a relative displacement between the multipole magnet and yoke.


- At this time, the magnetic flux from the N to S pole of the multipole magnet passes between the Hall ICs. The system detects the steered direction of the steering wheel in accordance with the direction of the magnetic flux that passes between the Hall ICs. Hall IC1 and Hall IC2 are installed facing opposite to each other. As a result, the output characteristics of the two Hall ICs are constantly opposite each other. The system monitors the different outputs of these Hall ICs in order to detect malfunctions.

- The magnetic flux density becomes higher as it gets closer to the center of the respective pole. A Hall IC converts these magnetic flux fluctuations into voltage fluctuations, in order to transmit the turning torque of the steering wheel to the EPS ECU.


Upon receiving the signals from the torque sensor, the EPS ECU calculates the required assist torque and outputs it to the motor.

X136207E01
3.604,3.406 3.938,2.573 3.938,2.573 4.188,2.573 true 1.458,2.073 2.99,2.271 1.531,0.198 10 false Right Turn 5.052,2.031 5.896,2.219 0.844,0.188 10 false Left Turn 0.156,1.323 0.781,1.542 0.625,0.219 8 false Hall IC2 3.729,1.302 4.354,1.521 0.625,0.219 8 false Hall IC2 3.073,1.281 3.698,1.5 0.625,0.219 8 false Hall IC1 6.604,1.26 7.104,1.479 0.5,0.219 8 false Hall IC1 0.229,2.479 1.615,2.896 1.385,0.417 10 false Torque Sensor Output Characteristics 2.073,2.531 2.365,2.792 0.292,0.26 10 false [V] 1.885,2.688 2.177,2.948 0.292,0.26 10 false 5.0 1.896,3.344 2.188,3.604 0.292,0.26 10 false 2.5 2,4.063 2.292,4.323 0.292,0.26 10 false 0 1.24,3.354 1.823,3.604 0.583,0.25 10 false Voltage 4.76,2.979 5.281,3.271 0.521,0.292 10 false TRQ1 4.771,3.708 5.25,3.979 0.479,0.271 10 false TRQ2 3.594,4.177 3.885,4.438 0.292,0.26 10 false 0 2.354,4.177 2.885,4.385 0.531,0.208 10 false -2.11 4.552,4.177 4.844,4.438 0.292,0.26 10 false 2.11 4.25,2.49 5.333,2.792 1.083,0.302 10 false Neutral Position 5.146,4.052 6.281,4.333 1.135,0.281 10 false [degrees] 2.5,4.344 3.344,4.531 0.844,0.188 10 false Left Turn 4.125,4.344 5.656,4.542 1.531,0.198 10 false Right Turn 2.823,4.573 4.865,4.792 2.042,0.219 10 false Twist Angle of Torsion Bar






b.

EPS ECU

i.

General

1.

The EPS ECU receives signals from various sensors, judges the current vehicle condition, and determines the assist current to be applied to the motor accordingly.

2.

In case a malfunction occurs in the system, the fail-safe function stops the output current and reverts the control to manual steering. At this time, a P/S warning light illuminates to alert the driver of the malfunction.

3.

The EPS ECU of the new models has following functions:

Item Function
Basic Control Calculates the assist current from the steering torque valve and the vehicle speed, and actuates the motor.
Inertia Compensation Control Ensures the starting movement of the motor when the driver starts to turn the steering wheel.
Recovery Control During the short interval between the time the driver fully turns the steering wheel and the wheels try to recover, this control assists the recovery force.
Damper Control Regulates the amount of assist when the driver turns the steering wheel while driving at high speeds, thus damping the changes in the yaw rate of the vehicle body.
System Overheat Protection Control Estimates the motor temperature based on the amperage and the current duration. If the temperature exceeds the standard, it limits the amperage to prevent the motor from overheating.

4.

The EPS ECU effects cooperative control with the skid control ECU, in order to control the steering assist torque in accordance with information received from the skid control ECU. This facilitates the steering operation of the driver, thus realizing a high level of vehicle stability.





DIAGNOSIS


a.

If the EPS ECU detects a malfunction in the EPS system, the warning light that corresponds to the function in which the malfunction has been detected lights up to alert the driver of the malfunction.


b.

At the same time, the DTCs (Diagnosis Trouble Codes) are stored in memory. The DTCs can be read by connecting an intelligent tester II, or by connecting the SST (09843-18040) to the TC and CG terminals of the DLC3 and observing the blinking of the P/S warning light.

HINT:

For details of the DTCs that are stored in EPS ECU memory, see the Previa/Tarago Repair Manual.




FAIL SAFE


a.

If the EPS ECU detects a malfunction in the EPS system, it turns ON the warning light in the combination meter to inform the driver and stops the assist control. As a result, the EPS system operates in the same way as manual steering.

Item Function
Torque Sensor System Malfunction Disables the assist.
Motor Overheating Limits the assist force.
Motor Short (Including drive system malfunction) Disables the assist.
Motor Overcurrent Disables the assist.
EPS ECU Internal Temperature Sensor Malfunction Limits the assist force.
EPS ECU System Malfunction Disables the assist.
Vehicle Speed and Engine Speed Signals Malfunction Temporarily limits the assist, returning to normal control when normal conditions are reestablished.
Power Supply Voltage Malfunction Temporarily limits the assist, returning to normal control when normal conditions are reestablished.