Home › Vehicle Interior › INTERIOR PANELS / TRIM › REAR POWER SUN SHADE SYSTEM
NM24M0E _58 Vehicle Interior _061589 INTERIOR PANELS / TRIM _0300342 REAR POWER SUN SHADE SYSTEM UN GENERAL/CONTROL/DETAILS F

INTERIOR PANELS / TRIM  REAR POWER SUN SHADE SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


SYSTEM CONTROL


a.

Initialization

i.

The rear power sunshade ECU memorizes the initial position of the rear power sunshade. Therefore, the data will be lost if the rear power sunshade motor assembly is removed. After reinstalling the rear power sunshade motor assembly, initialize the system by performing the steps described below. After removing the rear power sunshade motor assembly, delete the initial position from the rear power sunshade ECU memory.


ii.

Perform all the operations indicated below at the rear power sunshade switch located on the overhead console.

Method for deleting the initial position:
·

Press and hold the CLOSE switch until the rear power sunshade reaches its fully closed position. Continue to press the CLOSE switch for 10 seconds while the rear power sunshade is in its fully closed position.


Method for storing the legitimate initial position in memory:
·

Press the CLOSE switch while the power source mode is IG-ON. Continue to press the CLOSE switch for 1 second while the rear power sunshade is in its fully closed position.

·

After the system stores the initial position in memory, the rear power sunshade will move down slightly backward.





FUNCTION


a.

The rear power sunshade has following functions:

Function Outline
Manual Open-and-close This function causes the rear power sunshade to open (or close) when the OPEN switch (or CLOSE switch) is pressed for a maximum of 0.3 seconds. The rear power sunshade stops as soon as the switch is released.
One-touch Auto Open-and-close This function causes the rear power sunshade to be fully opened (or closed) when the OPEN switch (or CLOSE switch) is pressed for a minimum of 0.3 seconds.
Jam Protection This function retracts the rear power sunshade if an object becomes jammed while the rear power sunshade is being closed.


b.

Jam Protection Function

i.

The Hall IC converts the changes in the magnetic flux that occur through the rotation of the worm gear into pulse signals and outputs them to the rear power sunshade ECU.

Y209927C01
1.875,0.604 2.083,0.604 2.083,0.604 2.354,0.906 true 2.99,2.969 3.198,2.969 3.198,2.969 3.448,2.479 true 3.104,0.802 3.292,0.802 3.292,0.802 3.292,1.615 true 3.542,0.802 3.354,0.802 3.354,0.802 3.354,1.542 true 1.719,0.51 2.031,0.667 0.313,0.156 10 false *1 2.938,0.708 3.25,0.865 0.313,0.156 10 false *a 2.823,2.875 3.135,3.031 0.313,0.156 10 false *b 3.563,0.719 3.875,0.875 0.313,0.156 10 false *a
*1 Rear Power Sunshade Motor - -
*a Hall ICs *b Rear Power Sunshade ECU



ii.

To control the jam protection function, the rear power sunshade ECU determines the amount of movement and the jamming of the rear power sunshade from the pulse signals from the Hall IC1, and the moving direction of the rear power sunshade from the phase difference between the pulses from the Hall IC1 and Hall IC2.

Judgment of Amount of Movement and Jamming
Y209942E04
0.375,1.031 0.917,1.417 0.542,0.385 10 false Hall IC1 Signal 1.656,1.635 2.99,2.021 1.333,0.385 10 false Amount of Movement of Motor 1 Revolution 1.646,2.292 2.208,2.479 0.563,0.188 10 false Normal 4.531,2.292 5.188,2.5 0.656,0.208 10 false Jammed 5.573,1.625 6.906,2.083 1.333,0.458 10 false Amount of Movement of Motor 1 Revolution

Judgment of Moving Direction
Y209943E02
0.667,0.76 1.208,1.167 0.542,0.406 10 false Hall IC1 Signal 0.667,1.667 1.208,2.052 0.542,0.385 10 false Hall IC2 Signal 1.917,2.333 2.531,2.531 0.615,0.198 10 false OPEN 4.833,2.333 5.417,2.5 0.583,0.167 10 false CLOSE