Home › Drivetrain › U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
NM24M0E _52 Drivetrain _061697 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0300971 AUTOMATIC TRANSMISSION SYSTEM UN GENERAL/CONTROL/DETAILS F

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


SYSTEM CONTROL


a.

The electronic control system of the U660E automatic transaxle uses the controls listed below.

Control Outline
Shift Timing Control The ECT ECU supplies current to 6 solenoid valves (SL1, SL2, SL3, SL4, SL and/or SLU) based on signals from each sensor to shift the gear.
Clutch to Clutch Pressure Control Controls the pressure that is applied directly to the C1, C2 clutches and B1, B3 brakes by actuating the shift solenoid valves (SL1, SL2, SL3 and SL4) in accordance with ECT ECU signals.
Line Pressure Control Actuates solenoid valve SLT to control the line pressure in accordance with information from the ECT ECU and the operating conditions of the transaxle.
Powertrain Cooperative Control Controls both the shift control and engine output control in an integrated way, achieving excellent shift characteristics and drivability.
Lock-up Timing Control The ECT ECU supplies current to shift solenoid valves SL and SLU based on signals from each sensor and engages or disengages the lock-up clutch.
Flex Lock-up Clutch Control Controls solenoid valves SLU and SL, provides an intermediate mode between the ON/OFF operations of the lock-up clutch, and increases the operating range of the lock-up clutch to improve fuel economy.
Coast Downshift Control The ECT ECU performs downshift control so that fuel cut control can continue for as long as possible during deceleration.
AI (Artificial Intelligence)-SHIFT Control Based on the signals from various sensors, the ECT ECU determines the road condition and the intention of the driver. Thus, the shift pattern is automatically regulated to an optimal level, improving drivability.
Multi-mode Automatic Transmission The ECT ECU appropriately controls the automatic transaxle in accordance with the shift range selected while the shift lever is in the S mode position.
Fail-safe Even if a malfunction is detected in the sensors or solenoids, the ECT ECU activates fail-safe control to prevent the vehicle's drivability from being significantly affected.
Diagnosis When the ECT ECU detects a malfunction, the ECT ECU makes a diagnosis and memorizes the malfunctioning part.


b.

Clutch to Clutch Pressure Control

i.

Clutch to clutch pressure control is used for shift control. As a result, shift control in the 2nd gear or above is possible without using the one-way clutch, and the automatic transaxle has been made lightweight and compact.


ii.

Using the fluid pressure circuit which enables the clutches and brakes (C1, C2, B1 and B3) to be controlled independently, and the high flow linear solenoid valves SL1, SL2, SL3 and SL4 which directly control the line pressure, the ECT ECU controls each clutch and brake accordingly with the optimum fluid pressure and timings in accordance with the information transmitted by the sensors, and then shifts the gears. As a result, highly responsive and excellent shift characteristics have been realized.

X136000E01
0.24,0.635 1.823,0.823 1.583,0.188 10 false ATF Temperature Sensor 0.094,1.208 1.844,1.417 1.75,0.208 10 false Input Turbine Speed Sensor 0.063,1.802 1.854,2 1.792,0.198 10 false Counter Gear Speed Sensor 2.365,1.177 3.031,1.365 0.667,0.188 10 false ECT ECU 3.094,1.396 4.146,1.802 1.052,0.406 10 false CAN (Powertrain Bus) 4.188,1.104 4.979,1.313 0.792,0.208 10 false Engine ECU 5.417,0.635 6.427,0.833 1.01,0.198 10 false Air Flow Meter 5.417,1.219 7.135,1.417 1.719,0.198 10 false Water Temperature Sensor 5.417,1.802 6.979,2.01 1.563,0.208 10 false Throttle Position Sensor 1.094,3.302 1.552,3.5 0.458,0.198 10 false SL1 1.75,3.667 2.063,3.865 0.313,0.198 10 false C1 2.427,3.292 2.885,3.49 0.458,0.198 10 false SL2 3.104,3.677 3.417,3.875 0.313,0.198 10 false C2 3.885,3.323 4.344,3.521 0.458,0.198 10 false SL3 4.542,3.688 4.854,3.885 0.313,0.198 10 false B1 5.24,3.313 5.698,3.51 0.458,0.198 10 false SL4 5.99,3.688 6.302,3.885 0.313,0.198 10 false B3 5.25,4.365 6.177,4.573 0.927,0.208 10 false Line Pressure



c.

Line Pressure Control

i.

The line pressure is controlled by using solenoid valve SLT. Through the use of solenoid valve SLT, the line pressure is optimally controlled in accordance with the engine torque information, as well as with the internal operating conditions of the torque converter and the transaxle. Accordingly, the line pressure can be accurately controlled in accordance with the engine output, traveling condition, and the ATF temperature, thus realizing smooth shift characteristics and optimizing the workload of the oil pump.

X136028E01
1.219,0.74 2.156,0.948 0.938,0.208 10 false Line Pressure 2.021,1.417 3.219,1.615 1.198,0.198 10 false Primary Regulator 1.417,3.49 2.031,3.688 0.615,0.198 10 false Pump 1.75,4.573 2.688,4.771 0.938,0.198 10 false Fluid Pressure 3.042,5.188 3.604,5.375 0.563,0.188 10 false Current 4.271,3.5 5.531,3.698 1.26,0.198 10 false Solenoid Valve SLT 4.938,0.906 5.417,1.26 0.479,0.354 10 false Engine ECU 4.844,2.49 5.5,2.688 0.656,0.198 10 false ECT ECU 5.938,0.5 6.823,0.875 0.885,0.375 10 false Throttle Valve Opening 5.875,0.906 6.885,1.104 1.01,0.198 10 false Intake Air Mass 5.781,1.188 7.021,1.385 1.24,0.198 10 false Water Temperature 5.698,1.49 6.698,1.708 1,0.219 10 false Engine Speed 5.917,2.198 6.813,2.396 0.896,0.198 10 false Shift Position 5.823,2.49 6.99,2.698 1.167,0.208 10 false ATF Temperature 5.719,2.844 7,3.24 1.281,0.396 10 false Input Turbine Speed Sensor

*: This diagram illustrates the fundamentals of line pressure control. The valve shapes differ from the actual ones.




d.

Powertrain Cooperative Control

i.

By controlling the engine output in cooperative control with ETCS-i (Electronic Throttle Control System-intelligent) when the vehicle is launched, excellent launch performance (improved response and suppression of tire slippage) is ensured.

Throttle Control at Launch
X136001E01
0.104,0.906 1.052,1.313 0.948,0.406 10 false Accelerator Pedal Opening 6.115,0.635 7.063,0.854 0.948,0.219 10 false : Conventional 6.115,0.906 6.688,1.094 0.573,0.188 10 false : U660E 1.458,2.24 2.938,2.438 1.479,0.198 10 false Linear Output Increase 4.302,1.875 5.969,2.073 1.667,0.198 10 false Tire Slippage Suppression 0.177,1.542 1.052,1.948 0.875,0.406 10 false Throttle Valve Opening 0.313,3.031 1.052,3.25 0.74,0.219 10 false Drive Force 5.813,3.198 6.219,3.385 0.406,0.188 10 false Time


ii.

The TCM determines the gear that is to be selected when the accelerator pedal is released (released completely) in accordance with the way the accelerator pedal is released (quickly or slowly) during deceleration. In this way, unnecessary upshifts are prevented during deceleration, matching the driver's intentions. In addition, unintended downshifts are prevented when accelerating the vehicle again, achieving smooth acceleration.

Deceleration Force Control
X136002E01
0.156,0.521 1.323,1.073 1.167,0.552 10 false Variation in Accelerator Pedal Operation 0.396,1.844 1.281,2.083 0.885,0.24 10 false Gear Position 0.542,2.333 1.302,2.5 0.76,0.167 10 false Drive Force 4.042,0.208 6.24,0.427 2.198,0.219 10 false : Slow Accelerator Pedal Operation 4.052,0.49 6.49,0.719 2.438,0.229 10 false : Sudden Accelerator Pedal Operation 1.417,1.781 1.875,1.979 0.458,0.198 10 false 3rd 2.042,1.625 2.5,1.823 0.458,0.198 10 false 4th 2.604,1.469 3.063,1.667 0.458,0.198 10 false 5th 2.865,1.323 3.323,1.521 0.458,0.198 10 false 6th 4.719,2 6.198,2.385 1.479,0.385 10 false Driver Force is changed by driver's input 6.375,3.198 6.99,3.396 0.615,0.198 10 false Time


iii.

Through cooperative control with ETCS-i (Electronic Throttle Control System-intelligent) and ESA (Electronic Spark Advance), and electronic control of the engagement and release speed of the clutch and brake hydraulic pressure, excellent response and shift shock reduction have been achieved.

Transient Shifting Control
X136003E01
1.51,0.365 2.49,0.781 0.979,0.417 10 false Driver's desired drive force 2.542,1.26 3.365,1.469 0.823,0.208 10 false Engine ECU 0.771,1.667 1.906,2.073 1.135,0.406 10 false Accelerator Pedal Operation 4.698,1.24 5.375,1.417 0.677,0.177 10 false ECT ECU 1.583,2.063 2.719,2.26 1.135,0.198 10 false ● ETCS-i Control 1.594,2.26 2.583,2.438 0.99,0.177 10 false ● ESA Control 3.479,1.896 5.052,2.521 1.573,0.625 10 false Optimal clutch and brake engagement hydraulic pressure and timing 5.521,2.083 6.938,2.313 1.417,0.229 10 false Drives Solenoid Valve 5.667,3.073 6.99,3.448 1.323,0.375 10 false Solenoid Valve (SL1, SL2, SL3, SL4) 1.594,3.865 2.573,4.271 0.979,0.406 10 false Optimal engine output 4.76,3.854 6.042,4.25 1.281,0.396 10 false Driver's desired drive force is achieved



e.

Lock-up Timing Control

i.

The ECT ECU operates the lock-up timing control in order to improve the fuel economy while in the 2nd gear or above with the shift lever in the D, S6, S5 and S4 range.

X136029E01
2.479,1.677 2.521,1.677 2.521,1.677 2.521,1.917 true 2.688,1.677 2.625,1.677 2.625,1.677 2.625,1.917 true 2.604,0.667 4.344,0.906 1.74,0.24 10 false : Lock-up Operating Range 1.771,0.823 2.167,1.031 0.396,0.208 10 false Large 0.885,1.417 1.938,1.833 1.052,0.417 10 false Throttle Opening Angle 2.229,1.594 2.542,1.781 0.313,0.188 10 false 2nd 2.719,1.594 3.01,1.771 0.292,0.177 10 false 3rd 2.74,1.906 3.198,2.104 0.458,0.198 10 false 4th 2.958,1.854 3.229,2.042 0.271,0.188 10 false 5th 4.375,1.802 4.833,2 0.458,0.198 10 false 6th 3.875,2.198 4.49,2.396 0.615,0.198 10 false High 3.271,2.458 4.271,2.667 1,0.208 10 false Vehicle Speed

Lock-up Operation:
Gear Shift Lever Position or Range
D or S6 S5 S4

○: Operates

X: Does not operate

-: Not applicable

1st X X X
2nd ○ ○ ○
3rd ○ ○ ○
4th ○ ○ ○
5th ○ ○ -
6th ○ - -



f.

Flex Lock-up Clutch Control

i.

In addition to the conventional lock-up timing control, flex lock-up clutch control is used.


ii.

This flex lock-up clutch control regulates solenoid valve SLU as an intermediate mode between the ON and OFF operations of the lock-up clutch.


iii.

During acceleration, flex lock-up clutch control operates when the gear position is the 2nd or higher and the shift lever is in the D, S6, S5 or S4 range. During deceleration, it operates when the gear position is the 4th or higher and the shift lever is in the D, S6, S5 or S4 range.


iv.

During acceleration, the partition control of the power transmission between the lock-up clutch and torque converter greatly boosts the transmission efficiency in accordance with the driving conditions, improving the fuel economy.


v.

During deceleration, the lock-up clutch is made to operate. Therefore the fuel-cut area is expanded and the fuel economy is improved.


vi.

By allowing flex lock-up clutch control to continue operating during gearshift, the smooth torque transmission has been obtained. As a result, the fuel economy and drivability have been improved.

X100037E17
4.375,3.594 4.604,3.365 4.604,3.365 4.833,3.365 false 4.583,4.188 4.854,4.625 4.854,4.625 5.135,4.625 false 4.229,4.406 4.229,5.24 false 2.177,3.51 1.802,3.802 1.802,3.802 1.656,3.802 false 2.292,1.24 2.573,1.656 2.573,1.656 2.573,1.75 false 2.885,4.396 3.927,4.396 false 2.729,3.031 2.604,2.583 2.604,2.583 2.198,2.583 false 1.531,1.333 1.531,0.521 1.531,0.521 1.646,0.521 false 3.896,0.719 3.896,0.156 3.896,0.156 4.135,0.156 false 3.667,2.302 4.125,2.969 0.458,0.667 10 false Engine Speed Signal 6.448,1.417 7.01,2.021 0.563,0.604 10 false Linear Solenoid Signal 0.708,2.479 2.219,2.708 1.51,0.229 10 false Throttle Position Sensor 1.25,1.646 2.167,2.021 0.917,0.375 10 false Vehicle Speed 1.51,4.313 2.927,4.51 1.417,0.198 10 false Lock-up Control Valve 3.552,5.292 5.135,5.5 1.583,0.208 10 false Shift Solenoid Valve SLU 5.198,4.51 6.844,4.76 1.646,0.25 10 false ATF Temperature Sensor 5.063,1.396 5.552,1.771 0.49,0.375 10 false Current 5.708,2.042 6.052,2.271 0.344,0.229 10 false Time 4.208,0.063 5.688,0.302 1.479,0.24 10 false CAN (Powertrain Bus) 3,0.667 3.344,1.042 0.344,0.375 10 false ECM 4.354,0.625 4.979,0.833 0.625,0.208 10 false ECT ECU 1.688,0.385 2.583,0.802 0.896,0.417 10 false Engine Speed Signal 2.333,1.76 3.208,2.156 0.875,0.396 10 false Input Speed Sensor Signal 4.875,3.25 5.781,3.604 0.906,0.354 10 false Input Turbine Speed Sensor 0.802,0.99 1.271,1.427 0.469,0.438 10 false Engine Speed 0.438,3.698 1.656,4.115 1.219,0.417 10 false Water Temperature Sensor

X136030E01
2.604,0.51 4.292,0.719 1.688,0.208 8 false : Lock-up Operating Range 2.604,0.698 5.021,0.885 2.417,0.188 8 false : Flex Lock-up Operating Range (Acceleration) 2.604,0.896 4.99,1.094 2.385,0.198 8 false : Flex Lock-up Operating Range (Deceleration) 1.771,0.698 2.167,0.896 0.396,0.198 10 false Large 0.917,1.281 1.969,1.677 1.052,0.396 10 false Throttle Opening Angle 3.094,2.313 4.115,2.51 1.021,0.198 10 false Vehicle Speed 4.698,2.25 5.313,2.448 0.615,0.198 10 false High

Flex Lock-up Operation:
Shift Range Gear Acceleration Flex Lock-up Deceleration Flex Lock-up

○: Operates

X: Does not operate

D, S6 1st X X
2nd ○ X
3rd ○ X
4th ○ ○
5th ○ ○
6th ○ ○
S5 1st X X
2nd ○ X
3rd ○ X
4th ○ ○
5th ○ ○
S4 1st X X
2nd ○ X
3rd ○ X
4th ○ ○



g.

Coast Downshift Control

i.

The ECT ECU effects coast downshift control in order to prolong the fuel cut control that is effected by the engine ECU during deceleration. In this way, the fuel economy is improved.


ii.

In this control, the transaxle downshifts from 6th to 5th and then 5th to 4th before fuel cut control ends when the vehicle is decelerated in the 6th gear, so that fuel cut control continues operating.

With Coast Downshift Control (6A/T)
X136031E01
0.708,0.25 2.01,0.448 1.302,0.198 10 false Fuel Cut Control ON 0.635,0.542 2.021,0.74 1.385,0.198 10 false Fuel Cut Control OFF 0.542,1.042 2.021,1.229 1.479,0.188 10 false Accelerator Pedal OFF 1,1.688 1.958,1.906 0.958,0.219 10 false Engine Speed 2.469,2.01 2.729,2.198 0.26,0.188 10 false 6th 3.01,2.01 3.281,2.188 0.271,0.177 10 false 5th 3.417,2.01 3.667,2.208 0.25,0.198 10 false 4th 3.51,2.469 3.99,2.646 0.479,0.177 10 false Time 5.333,1.313 6.698,1.521 1.365,0.208 10 false Fuel Cut Control ON 5.333,1.948 6.688,2.135 1.354,0.188 10 false Fuel Cut Control OFF

Without Coast Downshift Control (5A/T)
X136032E01
0.719,0.281 2.031,0.49 1.313,0.208 10 false Fuel Cut Control ON 0.646,0.604 2.021,0.781 1.375,0.177 10 false Fuel Cut Control OFF 0.563,1.052 2.031,1.24 1.469,0.188 10 false Accelerator Pedal OFF 1.094,1.604 2.052,1.813 0.958,0.208 10 false Engine Speed 2.354,2.104 2.813,2.302 0.458,0.198 10 false 5th 3.052,2.073 3.323,2.281 0.271,0.208 10 false 4th 3.51,2.458 4.125,2.656 0.615,0.198 10 false Time 5.375,1.313 6.667,1.51 1.292,0.198 10 false Fuel Cut Control ON 5.396,1.958 6.75,2.135 1.354,0.177 10 false Fuel Cut Control OFF



h.

AI (Artificial Intelligence)-SHIFT Control

i.

AI-SHIFT control enables the ECT ECU to estimate the road conditions and the driver's intention in order to automatically control the shift pattern in the optimal manner. As a result, a comfortable ride has been achieved.

X136035E01
0.688,0.313 1.5,0.51 0.813,0.198 10 true Input Signal 0.677,0.729 1.635,0.938 0.958,0.208 10 false Sensor Signal 0.563,1.167 1.667,1.625 1.104,0.458 10 false ● Throttle Opening Angle 0.563,1.688 1.688,1.885 1.125,0.198 10 false ● Vehicle Speed 0.552,2.052 1.656,2.26 1.104,0.208 10 false ● Engine Speed 0.563,2.396 1.583,2.656 1.021,0.26 10 false ● Brake Signal 0.49,3.208 1.729,3.406 1.24,0.198 10 false Calculation by ECU 0.667,3.604 1.563,3.99 0.896,0.385 10 false Vehicle Acceleration 2.438,1.094 3.448,1.302 1.01,0.208 10 true Road Condition 2.667,1.302 4.063,1.51 1.396,0.208 10 true Uphill/Downhill Driving 3.354,1.75 4.542,1.969 1.188,0.219 10 false Estimating Grade 2.615,0.448 3.25,0.635 0.635,0.188 10 false AI-SHIFT 5.667,0.5 6.719,0.917 1.052,0.417 10 false Basic Shift Pattern Control 5.698,1.802 6.677,2.25 0.979,0.448 10 false Road Condition Support Control 5.688,3.677 6.719,4.073 1.031,0.396 10 false Driver's Intention Support Control 2.604,1.865 3.167,2.063 0.563,0.198 10 false Smaller 3.708,2.021 4.26,2.208 0.552,0.188 10 false Greater 3.188,2.833 4.531,3.031 1.344,0.198 10 false : Actual Acceleration 3.188,2.625 4.635,2.823 1.448,0.198 10 false : Criterion Acceleration 2.49,3.292 3.542,3.49 1.052,0.198 10 true Driver's Intention 2.479,3.542 3.542,3.917 1.063,0.375 10 false ● Acceleration Pedal Operation 2.469,3.885 3.104,4.219 0.635,0.333 10 false ● Vehicle Condition 3.938,3.583 5.01,4.115 1.073,0.531 10 false Estimating Driver's Intention

1.

Road Condition Support Control

Under road condition support control, the ECT ECU determines the throttle valve opening angle and the vehicle speed whether the vehicle is being driven uphill or downhill. To achieve the optimal drive force while driving uphill, this control prevents the transaxle from upshifting to the 5th or 6th gear. To achieve the optimal engine brake effect while driving downhill, this control automatically downshifts the transaxle to the 5th, 4th or 3rd gear.

X100042E14
4.167,3.125 4.167,2.635 4.167,2.635 4.042,2.635 false 0.75,3.156 1.031,3.344 0.281,0.188 10 false 6th 0.75,3.667 1.052,3.885 0.302,0.219 10 false 6th 1.427,3.156 1.677,3.365 0.25,0.208 10 false 4th 1.625,3.667 1.917,3.875 0.292,0.208 10 false 4th 1.854,3.156 2.135,3.354 0.281,0.198 10 false 5th 2.531,3.156 2.823,3.354 0.292,0.198 10 false 5th 2.167,3.156 2.385,3.344 0.219,0.188 10 false 3rd 2.167,3.667 2.396,3.854 0.229,0.188 10 false 3rd 2.906,3.156 3.198,3.344 0.292,0.188 10 false 4th 4.365,3.667 4.604,3.854 0.24,0.188 10 false 3rd 3.281,3.667 3.698,3.865 0.417,0.198 10 false 4th 4.823,3.667 5.188,3.854 0.365,0.188 10 false 4th 5.292,3.667 5.542,3.865 0.25,0.198 10 false 5th 5.583,3.667 5.885,3.885 0.302,0.219 10 false 6th 5.458,3.167 5.771,3.375 0.313,0.208 10 true 6th 5.969,3.125 6.969,3.302 1,0.177 10 false Without Control 5.99,3.635 6.802,3.813 0.813,0.177 10 false With Control 3.365,2.531 4.042,2.969 0.677,0.438 10 false 5th (Brake Operating)


2.

Driver's Intention Support Control

The driver's intention is estimated based on the accelerator pedal operation and vehicle condition to switch to a shift pattern that is well-suited to the driver, without the need to operate the shift pattern select switch used in the conventional models.





i.

Multi-mode Automatic Transmission

i.

In the S mode position, by moving the shift lever to the front ("+" position) or to the rear ("-" position), the driver can select the desired shift range. Thus, the driver is able to shift gears with a manual-like feel.


ii.

The multi-mode automatic transmission is designed to allow the driver to switch the gear ranges.


iii.

An S mode indicator light which illuminates when the S mode position is selected and a shift range indicator light which indicates the shift range have been provided in the combination meter.

X136033E01
1.792,0.719 3.073,0.917 1.281,0.198 10 false Combination Meter 1.698,1.146 3.146,1.354 1.448,0.208 10 false S Mode Indicator Light 1.542,1.49 3.417,1.875 1.875,0.385 10 false Shift Range and Shift Position Indicator Light 1.875,2.021 3.031,2.229 1.156,0.208 10 false CAN (No. 1 Bus) 1.99,2.635 2.896,2.833 0.906,0.198 10 false Engine ECU 0.427,4.135 1.479,4.51 1.052,0.375 10 false Ignition Advance Control 2.552,4.042 3.24,4.25 0.688,0.208 10 false ECT ECU 3.792,2.25 4.802,2.438 1.01,0.188 10 false Shift-up Signal 3.792,2.604 5.042,2.802 1.25,0.198 10 false Shift-down Signal 3.656,2.875 5.125,3.073 1.469,0.198 10 false S Mode Position Signal 5.146,2.49 6.063,3.042 0.917,0.552 10 false Transmission Control Switch 2.958,3.448 4.385,3.656 1.427,0.208 10 false CAN (Powertrain Bus) 1.396,5.354 1.917,5.583 0.521,0.229 10 false Engine 3.042,5.531 3.354,5.719 0.313,0.188 10 false A/T 3.229,4.698 4.198,5.104 0.969,0.406 10 false Solenoid Valve Control Signal


iv.

The driver selects the S mode position by moving the shift lever. At this time, the 4th or 5th range is selected according to the vehicle speed. (During AI-SHIFT control, the shift range that has the currently controlled gear position as the maximum usable gear position is displayed.) Then, the shift range changes one at a time, as the driver moves the shift lever to the front ("+" position) or to the rear ("-" position).


v.

Under this control, the ECT ECU effects optimal shift control within the usable gear range that the driver has selected. As with an ordinary automatic transmission, it shifts to the 1st gear when the vehicle is stopped.


vi.

When the shift lever is in the S mode position, the S mode indicator light in the combination meter illuminates. The shift range indicator light indicates the shift range that the driver has selected.

X136037E01
1.813,1.396 2.615,1.76 0.802,0.365 10 false Transition of Shift Range 1.781,5.063 3.188,5.292 1.406,0.229 10 false : Default Shift Range 3.583,1.656 4.688,1.854 1.104,0.198 10 false S Mode Position 4.385,3.354 5.292,3.563 0.906,0.208 10 false Shift Pattern

Usable Gear Chart:
Shift Range Indicator Light Indication Shift Range Usable Gear
6 6 1st to 6th
5 5 1st to 5th
4 4 1st to 4th
3 3 1st to 3rd
2 2 1st to 2nd
1 1 1st



j.

ECT ECU

i.

The ECT ECU has been isolated from the engine ECU and directly fitted to the transaxle. All the solenoid valves and sensors used for automatic transaxle control are directly connected to the ECT ECU through the connector located in front of the automatic transaxle.


ii.

The ECT ECU maintains communication with the engine ECU through the CAN (Controller Area Network). Thus, engine control is effected in coordination with ECT control.


iii.

A label, on which the automatic transaxle compensation value and QR (Quick Response) code are printed, is attached on the top of the automatic transaxle. The label contains encoded automatic transaxle property information. When the automatic transaxle is replaced, allow the ECT ECU to learn the automatic transaxle property information by inputting the automatic transaxle compensation values into the ECT ECU using an intelligent tester II. In this way, the shift control performance immediately after replacement of the automatic transaxle is improved. For details, see the Previa/Tarago Repair Manual.


iv.

The QR code, which requires a special scan tool, is used at the vehicle assembly plant.

X136012C01
0.99,0.76 1.24,0.76 1.24,0.76 1.552,1.354 true 0.917,4.167 1.167,4.167 1.167,4.167 1.865,3 true 4.729,0.458 4.979,0.458 4.979,0.458 5.292,1.052 true 4.51,1.948 4.76,1.948 4.76,1.948 5.24,1.708 true 0.781,0.667 0.979,0.844 0.198,0.177 10 false *1 0.719,4.073 0.917,4.25 0.198,0.177 10 false *4 4.563,0.365 4.76,0.542 0.198,0.177 10 false *2 4.323,1.854 4.521,2.031 0.198,0.177 10 false *3 4.5,4.208 4.698,4.385 0.198,0.177 10 false *a

Text in Illustration
*1 ECT ECU *2 QR Code
*3 Automatic Transaxle Compensation Value *4 Transaxle Connector
*a Automatic Transaxle Front View - -

HINT:

What are Quick Response (QR) Codes?

·

QR code, a matrix symbology consisting of an array of nominally square cells, allows omni-directional, high-speed reading of large amounts of data.

·

QR codes encode many types of data such as numeric, alphanumeric, kanji, kana and binary codes. A maximum of 7,089 characters (numeric) can be encoded.

·

QR codes (2D code) contain information in the vertical and horizontal directions, whereas bar codes only contain data in one direction. QR codes (2D code) hold considerably greater volumes of information than bar codes.





k.

ATF Pressure Switch

i.

The ATF pressure switches are located in the output fluid passages of the solenoid valves SL1, SL2 and SLU, and turn ON/OFF in accordance with the solenoid valve output fluid pressure.

The conditions of the ATF pressure switches when the vehicle is running normally are as follows.

*: During Lock-up Control or Flex Lock-up Control

Gear 1st 2nd 3rd 4th 5th 6th
ATF Pressure Switch 1 ON ON ON ON OFF OFF
ATF Pressure Switch 2 OFF OFF OFF ON ON ON
ATF Pressure Switch 3 OFF OFF/ON* OFF/ON* OFF/ON* OFF/ON* OFF/ON*


ii.

The ECT ECU detects malfunctions in solenoid valves SL1, SL2, SL3 and SL4 in accordance with the ON/OFF signals from ATF pressure switches 1 and 2. At this time, the ECT ECU determines the appropriate fail-safe operation.


iii.

The ECT ECU detects malfunctions in solenoid valves SLU and SL used in lock-up control in accordance with the ON/OFF signals from ATF pressure switch 3.

X136026E01
5.646,1.406 5.646,1.104 true 1.063,0.635 1.208,0.635 1.208,0.635 1.75,1.458 true 2.25,1.552 2.25,0.333 true 2.771,1.583 3.313,0.198 3.313,0.198 3.458,0.198 true 3.771,1.417 4.26,0.99 4.26,0.99 4.406,0.99 true 3.26,2.031 3.385,2.51 3.385,2.51 3.531,2.51 true 2.75,2.385 2.75,2.063 true 1.948,2.469 2.104,2.469 2.104,2.469 2.24,1.99 true 1.427,2.458 1.583,2.458 1.583,2.458 1.833,1.802 true 0.99,2.281 1.146,2.281 1.146,2.281 1.271,1.781 true 0.177,0.521 1.063,0.927 0.885,0.406 10 false ATF Pressure Switch 3 1.542,0.167 3.052,0.365 1.51,0.198 10 false ATF Pressure Switch 2 3.49,0.115 5.083,0.302 1.594,0.188 10 false ATF Pressure Switch 1 4.438,0.917 4.896,1.115 0.458,0.198 10 false SL4 3.563,2.427 4.021,2.625 0.458,0.198 10 false SL3 2.625,2.396 3.083,2.594 0.458,0.198 10 false SL1 1.688,2.396 2.146,2.594 0.458,0.198 10 false SL2 1.125,2.385 1.583,2.583 0.458,0.198 10 false SLU 0.792,2.188 1.104,2.385 0.313,0.198 10 false SL 5.073,0.906 6.469,1.115 1.396,0.208 10 false ATF Pressure Switch 5.042,1.938 6.396,2.323 1.354,0.385 10 false ATF Pressure Switch Cross Section 2.156,2.594 3.396,2.792 1.24,0.198 10 false Lower Valve Body



l.

ATF Temperature Sensor

i.

The ATF temperature sensor is installed in the lower valve body for direct detection of the fluid temperature.

The conditions of the ATF pressure switches when the vehicle is running normally are as follows.


ii.

The ATF temperature sensor is used for the correction of clutch and brake pressure to keep smooth shift quality every time.The ATF temperature sensor is used for the correction of clutch and brake pressure to keep smooth shift quality every time.

X136010E01
5.885,0.656 5.885,0.927 true 5.177,0.438 6.802,0.656 1.625,0.219 10 false ATF Temperature Sensor 2.208,2.521 3.49,2.74 1.281,0.219 10 false Lower Valve Body



m.

Speed Sensors

i.

The U660E automatic transaxle uses an input turbine speed sensor (for the NT signal) and a counter gear speed sensor (for the NC signal). Thus, the ECT ECU can detect the timing of the shifting of the gears and appropriately control the engine torque and hydraulic pressure in response to the various conditions. These speed sensors are the Hall type.


ii.

The input turbine speed sensor detects the input speed of the transaxle. The No. 2 clutch piston is used as the timing rotor for this sensor.


iii.

The counter gear speed sensor detects the speed of the counter gear. The counter drive gear is used as the timing rotor for this sensor.


iv.

The Hall type speed sensor consists of a magnet and Hall IC. The Hall IC convents the changes in the magnetic flux density that occur through the rotation of the timing rotor into electric signal, and outputs the signal to the ECT ECU.

X135999E01
1.969,0.792 2.125,0.792 2.125,0.792 2.948,1.156 true 2.938,0.25 3.094,0.25 3.094,0.25 3.656,1.375 true 5.313,0.521 5.167,0.521 5.167,0.521 4.563,1.031 true 5.417,1.563 5.271,1.563 5.271,1.563 4.844,1.875 true 1.688,3.125 1.844,3.125 1.844,3.125 2.25,2.5 true 1.156,0.146 2.927,0.375 1.771,0.229 10 false Counter Gear Speed Sensor 0.219,0.688 1.99,0.906 1.771,0.219 10 false Input Turbine Speed Sensor 5.385,0.427 6.969,0.656 1.583,0.229 10 false No. 2 Upper Valve Body 5.479,1.479 7.094,1.708 1.615,0.229 10 false No. 1 Upper Valve Body 5.167,3.25 6.031,3.448 0.865,0.198 10 false Engine Side 0.542,3.021 1.802,3.219 1.26,0.198 10 false Lower Valve Body



n.

Transmission Control Switch and Neutral Start Switch

i.

The ECT ECU and engine ECU use these switches to detect the shift lever position.


ii.

The neutral start switch sends the P, R, N and D position signals to both the engine ECU and ECT ECU. The engine ECU transmits signals to the combination meter for the shift position indicator light (P, R, N and D) in response to the signal it receives from the switch.


iii.

The transmission control switch is installed inside the shift lever assembly. The switch terminal S is used to detect whether the shift lever is in the D position or S mode position, and the terminals SFTU and SFTD are used to detect the operating conditions of the shift lever (front [+ position] or rear [- position]) if S mode is selected. By transmitting signals to the engine ECU, the transmission control switch turns ON both the shift range indicator light and S mode indicator light when the shift lever is moved to the S mode position, and indicates the selected shift range through shift range indicator light.

X136027E01
0.042,1.146 0.885,1.51 0.844,0.365 10 false From Starter Cut Relay*2 1.01,0.552 1.469,0.75 0.458,0.198 10 false NSW 2.094,0.563 2.552,0.76 0.458,0.198 10 false STA 1.24,1.25 1.396,1.448 0.156,0.198 10 false B 0.021,1.844 0.958,2.052 0.938,0.208 10 false From IG Relay 1.125,1.979 1.438,2.177 0.313,0.198 10 false RB 2.51,1.073 3.635,1.292 1.125,0.219 10 false To Starter Relay 2.104,1.281 2.26,1.479 0.156,0.198 10 false L 2.094,1.583 2.406,1.781 0.313,0.198 10 false DL 2.052,1.885 2.365,2.083 0.313,0.198 10 false NL 2.073,2.188 2.385,2.385 0.313,0.198 10 false RL 2.083,2.448 2.396,2.646 0.313,0.198 10 false PL 1.104,2.708 2.417,2.917 1.313,0.208 10 false Neutral Start Switch 0.042,3.552 1.031,3.74 0.99,0.188 10 false From IG Relay 0.844,5.167 2.688,5.365 1.844,0.198 10 false Transmission Control Switch 2.094,3.656 2.25,3.854 0.156,0.198 10 false S 2.073,4.125 2.688,4.323 0.615,0.198 10 false SFTU 2.094,4.604 2.708,4.802 0.615,0.198 10 false SFTD 2.969,3.448 3.125,3.646 0.156,0.198 10 false S 2.719,3.906 3.125,4.104 0.406,0.198 10 false SFTU 2.719,4.385 3.135,4.573 0.417,0.188 10 false SFTD 3.25,3.979 4.063,4.177 0.813,0.198 10 false Engine ECU 3.135,3.115 3.292,3.313 0.156,0.198 10 false P 3.333,3.115 3.49,3.313 0.156,0.198 10 false R 3.563,3.104 3.719,3.302 0.156,0.198 10 false N 3.813,3.104 3.969,3.302 0.156,0.198 10 false D 5.333,3.104 5.49,3.302 0.156,0.198 10 false R 5.771,3.094 5.927,3.292 0.156,0.198 10 false D 4.146,4.26 5.198,4.677 1.052,0.417 10 false CAN (Powertrain Bus) 5.406,4.021 6.135,4.219 0.729,0.198 10 false ECT ECU 3.802,5.406 4.979,5.625 1.177,0.219 10 false CAN (No. 1 Bus) 3.063,6.104 4.333,6.281 1.271,0.177 10 false Combination Meter 2.927,6.417 4.396,6.583 1.469,0.167 10 false S Mode Indicator Light 2.74,6.688 4.5,7.115 1.76,0.427 9 false Shift Range and Shift Position Indicator Light 0.281,7.438 3.313,7.688 3.031,0.25 10 false *1: Models without Smart Entry & Start System 3.948,7.427 6.792,7.625 2.844,0.198 10 false *2: Models with Smart Entry & Start System 0.042,0.802 0.865,1.167 0.823,0.365 10 false From Ignition Switch*1




CONSTRUCTION


a.

DIFFERENTIAL CASE

i.

The curvature of the differential case opening, where tensile stress is concentrated during driving, is enlarged, in order to moderate the stress concentration and enhance the differential gear tolerant torque. As a result, use of the lightweight 2-pinion differential gears is possible.

X135986E01
1.813,2.26 2.115,1.865 2.115,1.865 2.26,1.865 true 2.365,2.823 2.667,2.427 2.667,2.427 2.813,2.427 true 2.5,3.281 3.104,3.719 3.104,3.719 3.25,3.719 true 2.417,3.719 3.094,4.24 3.094,4.24 3.24,4.24 true 5.354,2.229 5.823,3.271 5.823,3.271 5.969,3.271 true 1.365,0.354 2.427,0.552 1.063,0.198 10 false : Tensile Stress 1.365,0.542 2.781,0.771 1.417,0.229 10 false : Compressive Stress 2.302,1.76 3.417,1.958 1.115,0.198 10 false Differential Case 2.844,2.323 3.948,2.531 1.104,0.208 10 false Large Curvature 6.021,3.177 7.156,3.385 1.135,0.208 10 false Differential Case 3.313,3.646 4.969,3.885 1.656,0.24 10 false Differential Case Opening 3.281,4.167 4.427,4.375 1.146,0.208 10 false Small Curvature 0.146,4.583 3.979,4.781 3.833,0.198 10 false Stresses Applied to Differential Case Opening during Driving



b.

TORQUE CONVERTER

i.

A compact, lightweight and high-capacity torque converter is used.


ii.

In order to make the torque converter more compact and shorten its total length, the pump impeller, turbine runner, and stator have been made narrower, and the structure of the one-way clutch has been simplified.


iii.

Fluid passages and impeller configuration of this torque converter have been optimally designed. As a result, substantially enhanced transmission efficiency ensures better starting, acceleration and fuel economy.


iv.

Furthermore, a hydraulically operated lock-up mechanism, which enables the lock-up (flex lock-up) operation at low to high vehicle speeds, is used to reduce the slip loss of the torque converter.

X136013E01
2.24,0.427 2.344,0.427 2.344,0.427 3.156,0.76 true 2.24,0.781 2.354,0.781 2.354,0.781 3.26,1.156 true 2.396,2.688 2.51,2.688 2.51,2.688 3.458,2.198 true 2.385,3.396 2.5,3.396 2.5,3.396 3.5,2.875 true 3.781,0.844 4.438,0.5 4.438,0.5 4.573,0.5 true 3.677,1.25 4.49,0.844 4.49,0.844 4.625,0.844 true 4.115,1.844 4.469,1.635 4.469,1.635 4.604,1.635 true 1.281,0.323 2.292,0.521 1.01,0.198 10 false Lock-up Clutch 1.188,0.677 2.281,0.885 1.094,0.208 10 false Lock-up Damper 1.365,2.583 2.417,2.792 1.052,0.208 10 false One-way Clutch 1.406,3.281 2.427,3.5 1.021,0.219 10 false Turbine Runner 4.635,0.406 6.625,0.604 1.99,0.198 10 false Pump Impeller 4.677,0.771 5.594,0.969 0.917,0.198 10 false Stator 4.656,1.531 5.469,1.74 0.813,0.208 10 false Input Shaft



c.

OIL PUMP

i.

The oil pump is operated by the torque converter. It lubricates the planetary gear units and supplies operating fluid pressure for hydraulic control.


ii.

The pump cover is made of aluminum to reduce weight.

X136005E01
1.938,1.26 2.135,0.49 2.135,0.49 2.229,0.49 true 2.917,1.417 3.094,0.813 3.094,0.813 3.188,0.813 true 3.719,1.698 3.906,2.24 3.906,2.24 4,2.24 true 4.781,1.219 5.208,2.427 5.208,2.427 5.302,2.427 true 5.146,0.635 5.281,0.219 5.281,0.219 5.375,0.219 true 2.302,0.427 3.229,0.656 0.927,0.229 10 false Pump Body 3.24,0.75 3.958,0.948 0.719,0.198 10 false Drive Gear 4.052,2.167 4.802,2.354 0.75,0.188 10 false Driven Gear 5.406,0.125 6.708,0.333 1.302,0.208 10 false Pump Cover 5.354,2.344 6.177,2.552 0.823,0.208 10 false Stator Shaft



d.

OIL STRAINER

i.

A felt type oil strainer is used because it is lightweight, provides excellent filtering ability, is more reliable and free from maintenance.

X135987E01
1.896,1.813 1.896,2.344 true 3.771,1.99 3.771,2.354 true 1.604,2.365 2.427,2.573 0.823,0.208 10 false Oil Strainer 3.573,2.385 4.646,2.583 1.073,0.198 10 false Oil Pan



e.

ATF

i.

The ATF WS is used to reduce the resistance of the ATF and ensure fuel economy by reducing its viscosity in the practical operation range. At the high-temperature end, its viscosity is the same as that of the ATF Type T-IV, which ensures the durability of the automatic transaxle.


ii.

The ATF WS and other types of ATF (ATF Type T-IV, D-II) are not interchangeable.

X136040E01
2.344,1.219 2.865,0.76 2.865,0.76 3.052,0.76 true 5.302,0.302 6.51,0.5 1.208,0.198 10 false : ATF Type T-IV 5.313,0.49 6.542,0.688 1.229,0.198 10 false : ATF WS 3.125,0.677 5.729,0.875 2.604,0.198 10 false Reduced Viscosity 1.667,0.99 2.031,1.208 0.365,0.219 10 false High 0.802,1.365 1.521,1.594 0.719,0.229 10 false Viscosity 3.958,2.229 4.573,2.427 0.615,0.198 10 false High 3.396,2.531 4.229,2.74 0.833,0.208 10 false Temperature



f.

ATF FILLING PROCEDURES

i.

The ATF filling procedures have been changed in order to improve the accuracy of the ATF level when the transaxle is being repaired or replaced. As a result, the oil filler tube and oil level gauge used for a conventional automatic transaxle are discontinued, eliminating the need to inspect the fluid level as a part of routine maintenance.


ii.

This filling procedure employs a refill plug, overflow plug, ATF temperature sensor, and shift indicator light "D". After the transaxle is refilled with ATF, remove the overflow plug and drain the extra ATF at the proper ATF temperature. Thus, the appropriate ATF level can be obtained.

X135988E01
5.365,0.896 5.521,0.896 5.521,0.896 5.792,1.698 true 5.927,2.073 6.042,2.521 6.042,2.521 6.146,2.521 true 0.677,1.25 1.406,1.448 0.729,0.198 10 false Refill Plug 4.531,0.802 5.417,1 0.885,0.198 10 false Proper Level 6.188,2.417 7.104,2.646 0.917,0.229 10 false Overflow Plug

HINT:
ATF Filling procedures using SST (09843-18040)

When a large amount of ATF needs to be filled (i.e. after removal and installation of oil pan or torque converter), perform the procedure from step (a). When a small amount of ATF is required (i.e. after removal and installation of oil cooler tube, repair of a minor oil leak), perform the procedure from step (g).

(a)

Raise the vehicle while keeping it level.

(b)

Remove the refill plug and overflow plug.

(c)

Fill the transaxle with ATF WS through the refill plug hole until it overflows from the overflow plug hole.

*

ATF WS must be used to fill the transaxle.


(d)

Reinstall the overflow plug.

(e)

Add the specified amount of ATF (specified amount is determined by the procedure that was performed) and reinstall the refill plug.

Procedure Liters (US qts, Imp. qts)
Removal and installation of transaxle oil pan(including oil drainage) 2.8 (3.0, 2.5)
Removal and installation of transaxle valve body 3.2 (3.4, 2.8)
Replacement of torque converter 4.8 (5.0, 4.2)

(f)

Lower the vehicle.

(g)

Use the SST (09843-18040) to make shorts between the TC and CG terminals of the DLC3 connector.

X136041E01
3.198,0.24 3.302,0.24 3.302,0.24 3.448,0.625 true 3.698,1.208 3.823,1.563 3.823,1.563 3.938,1.563 true 2.969,0.167 3.281,0.365 0.313,0.198 10 false CG 3.979,1.479 4.292,1.677 0.313,0.198 10 false TC

(h)

Start the engine and allow it to idle.

*

A/C switch must be turned OFF.


(i)

Move the shift lever from the "P" position to the "S" mode position and slowly selects each gear S1 - S6. Then move the shift lever back to the "P" position.

(j)

Move the shift lever to the "D" position, and then quickly move it back and forth between "N" and "D" (at least once every 1.5 seconds) for at least 6 seconds. This will activate oil temperature detection mode.

Standard:

The shift position indicator light "D" remains illuminated for 2 seconds and then goes OFF.


(k)

Return the shift lever to the "P" position and disconnect the TC terminal.

(l)

Idle the engine to raise the ATF temperature.

(m)

Immediately after the shift position indicator light "D" turns ON, lift the vehicle up.

*

The shift position indicator light "D" will indicate the ATF temperature according to the following table.

ATF Temperature Lower than Optimal Temperature Optimal Temperature Higher than Optimal Temperature
Shift Position Indicator Light "D" OFF ON Blinking


(n)

Remove the overflow plug and adjust the oil quantity

*

If the ATF overflows, go to step (q), and if the ATF does not overflow, go to step (o).


(o)

Remove the refill plug.

(p)

Add ATF through the refill plug hole until it flows out from the overflow plug hole.

(q)

When the ATF flow slows to a trickle, install the overflow plug and a new gasket.

(r)

Reinstall the refill plug (if the refill plug was removed).

(s)

Lower the vehicle.

(t)

Turn the ignition switch (engine switch*) OFF to stop the engine.

*: Models with Smart Entry & Start System



For details about the ATF filling procedures, see the Previa/Tarago Repair Manual.





g.

PLANETARY GEAR UNIT

i.

The 6-speed configuration has been achieved by using 2 planetary gear units, creating a 6-speed automatic transaxle.


ii.

A Ravigneaux type planetary gear unit is used as the rear gear unit. The gear unit consists of pairs of sun gears (front and rear) and planetary pinion gears (long and short) with different diameters within a single planetary gear.


iii.

The centrifugal fluid pressure canceling mechanism is used in the C1 and C2 clutches that are applied when shifting between the 1st to 6th gears.


iv.

The shapes of the grooves in the clutches and brake linings have been optimized in order to reduce drag during clutch and brake operation.

X135985E01
4.563,2.917 4.844,2.917 true 4.594,3.406 4.875,3.406 true 3.479,3.333 3.479,3.51 true 1.573,3.01 1.688,3.01 1.688,3.01 2.229,2.479 true 2.552,3.271 2.667,3.271 2.667,3.271 2.667,2.365 true 1.427,2.563 1.542,2.563 1.542,2.563 2.083,2.031 true 1.313,2.177 1.427,2.177 1.427,2.177 1.698,1.906 true 2.844,1.479 3.042,0.49 3.042,0.49 3.177,0.49 true 2.917,1.625 3.104,0.677 3.104,0.677 3.198,0.677 true 2.979,1.792 3.146,0.917 3.146,0.917 3.229,0.917 true 4.167,1.198 4.271,1.198 4.271,1.198 4.427,1.583 true 4.667,1.563 5.177,1.219 5.177,1.219 5.313,1.219 true 5,1.667 5.302,1.458 5.302,1.458 5.438,1.458 true 5.615,1.885 5.792,1.885 true 4.927,2 5.302,2.24 5.302,2.24 5.521,2.24 true 3.729,2.271 4.156,2.531 4.156,2.531 4.708,2.531 true 2.146,0.49 2.458,0.688 0.313,0.198 10 false F1 2.594,0.531 2.906,0.729 0.313,0.198 10 false B2 3.24,0.385 4.427,0.573 1.188,0.188 10 false Long Pinion Gear 3.24,0.594 4.448,0.792 1.208,0.198 10 false Short Pinion Gear 3.281,0.823 4.292,1.01 1.01,0.188 10 false Front Sun Gear 3.5,1.125 4.146,1.333 0.646,0.208 10 false Ring Gear 4.458,0.542 4.771,0.74 0.313,0.198 10 false B3 4.917,0.531 5.229,0.729 0.313,0.198 10 false B1 1.698,0.885 2.01,1.083 0.313,0.198 10 false C1 1.708,1.302 2.021,1.5 0.313,0.198 10 false C2 0.156,2.083 1.365,2.271 1.208,0.188 10 false Intermediate Shaft 0.458,2.469 1.5,2.667 1.042,0.198 10 false Rear Sun Gear 0.198,2.906 1.552,3.323 1.354,0.417 10 false Ravigneaux Planetary Gear Unit 2.854,3.51 4.24,3.688 1.385,0.177 10 false Counter Driven Gear 1.875,3.177 2.573,3.375 0.698,0.198 10 false Ring Gear 4.771,2.448 6.021,2.646 1.25,0.198 10 false Counter Drive Gear 4.875,2.823 6.438,3.021 1.563,0.198 10 false Differential Drive Pinion 4.906,3.313 5.656,3.51 0.75,0.198 10 false Ring Gear 5.583,2.135 6.24,2.354 0.656,0.219 10 false Sun Gear 5.823,1.781 6.677,2.01 0.854,0.229 10 false Input Shaft 5.5,1.375 7.104,1.615 1.604,0.24 10 false U/D Planetary Gear Unit 5.375,1.125 7.063,1.323 1.688,0.198 10 false Pinion Gear

Function of Components
Component Function
C1 No. 1 Clutch Connects the intermediate shaft and Ravigneaux planetary rear sun gear.
C2 No. 2 Clutch Connects the intermediate shaft and Ravigneaux planetary ring gear.
B1 No. 1 Brake Prevents the Ravigneaux planetary front sun gear and U/D planetary carrier from turning either clockwise or counterclockwise.
B2 No. 2 Brake Prevents the Ravigneaux planetary ring gear from turning either clockwise or counterclockwise.
B3 No. 3 Brake Prevents the U/D planetary ring gear from turning either clockwise or counterclockwise.
F1 No. 1 One-way Clutch Prevents the Ravigneaux planetary ring gear from turning counterclockwise.
Planetary Gears These gears change the route through which driving force is transmitted, in accordance with the operation of each clutch and brake, in order to increase or reduce the input and output speeds.



h.

Centrifugal Fluid Pressure Canceling Mechanism

i.

There are two reasons for improving the conventional clutch mechanism:

·

To prevent the generation of pressure by the centrifugal force that is applied to the fluid in piston fluid pressure chamber (hereafter referred to as "chamber A") when the clutch is released, a check ball is provided to discharge the fluid. Therefore, before the clutch can be subsequently applied, it took time for the fluid to fill the chamber A.

·

During shifting, in addition to the original clutch pressure that is controlled by the valve body, the pressure that acts on the fluid in the chamber A also exerts influence, which is dependent upon revolution fluctuations.



ii.

To address these two needs for improvement, a canceling fluid pressure chamber (hereafter referred to as "chamber B") has been provided opposite chamber A.

X106203E06
1.729,1.979 1.354,1.979 false 2.292,2.531 2.292,2.76 false 1.896,1.844 1.302,1.292 1.302,1.292 1.104,1.292 false 1.844,1.948 1.167,1.49 1.167,1.49 1.083,1.49 false 1.917,2.229 1.563,2.74 1.563,2.74 1.417,2.74 false 2.219,2.417 1.948,2.792 1.948,2.792 1.844,2.792 false 0.948,1.177 1.177,1.344 0.229,0.167 10 false *1 1.188,1.875 1.375,2.042 0.188,0.167 10 false *2 1.25,2.625 1.438,2.792 0.188,0.167 10 false *3 0.917,1.375 1.146,1.542 0.229,0.167 10 false *1 2.24,2.792 2.427,2.958 0.188,0.167 10 false *2 1.667,2.688 1.854,2.854 0.188,0.167 10 false *3

Text in Illustration
*1 Chamber A *2 Chamber B
*3 Piston - -


iii.

By utilizing the lubrication fluid such as that of the shaft, the same amount of centrifugal force is applied, thus canceling the centrifugal force that is applied to the piston itself. Accordingly, it is not necessary to discharge the fluid through the use of a check ball, and a highly responsive and smooth shifting characteristic has been achieved.

X136039E01
3.375,2.01 4.188,2.188 0.813,0.177 0.573,2.26 6.781,2.729 6.208,0.469 3.969,0.573 4.063,0.573 4.063,0.573 4.063,0.833 true 3.094,0.958 3.177,0.406 false 3.135,1.219 3.177,0.427 3.177,0.427 3.219,1.458 false 2.938,1.219 1.958,1.104 1.958,1.104 2.979,1.479 false 2.865,0.969 1.99,1.104 false 4.396,1.021 3.542,0.979 false 3.49,1.208 4.375,1.021 4.375,1.021 3.448,1.469 false 4.385,1.615 4.26,1.615 4.26,1.615 3.635,1.5 true 2.573,1.521 2.375,1.719 2.375,1.719 2.271,1.719 true 2.958,1.635 2.958,1.75 2.958,1.75 3.188,1.75 false 3.021,1.75 3.24,1.75 3.24,1.75 3.24,1.646 false 3.115,1.75 2.948,2.01 2.948,2.01 2.844,2.01 true 2.063,0.073 3.688,0.448 1.625,0.375 10 false Centrifugal Fluid Pressure applied to the Chamber A 4.219,0.219 4.698,0.396 0.479,0.177 10 false Clutch 3.542,0.458 4.01,0.625 0.469,0.167 10 false Piston 0.615,1 2.021,1.24 1.406,0.24 10 false Target Fluid Pressure 0.104,1.625 2.313,1.854 2.208,0.229 10 false Chamber A (Piston Fluid Pressure) 0.854,1.917 2.875,2.146 2.021,0.229 10 false Fluid Pressure applied to Piston 4.458,0.927 6.052,1.281 1.594,0.354 10 false Centrifugal Fluid Pressure applied to Chamber B 4.448,1.521 6.854,1.729 2.406,0.208 10 false Chamber B (Canceling Fluid Pressure) 3.469,2.01 4.167,2.177 0.698,0.167 10 false Shaft Side 0.854,2.302 2.26,2.646 1.406,0.344 10 false Fluid pressure applied to piston 2.813,2.302 4.344,2.688 1.531,0.385 10 false Centrifugal fluid pressure applied to chamber B 4.813,2.302 6.615,2.667 1.802,0.365 10 false Target fluid pressure (original clutch pressure) 2.396,2.396 2.552,2.594 0.156,0.198 10 false - 4.521,2.427 4.677,2.625 0.156,0.198 10 false =



i.

Counter Drive Gear

i.

An angular ball bearing is used to support the counter drive gear and the Ravigneaux planetary gear unit, reducing the rolling resistance and noise.


ii.

By providing three elongated openings in the counter drive gear, the vibration conduction characteristic of the gear has been optimized. As a result, both gear noise and weight reductions have been achieved.

X135997E01
1.896,0.417 2.031,0.417 2.031,0.417 2.313,1.625 true 2.75,0.177 2.615,0.177 2.615,0.177 2.615,1.51 true 5.958,1.063 5.604,0.313 5.604,0.313 5.583,2.031 false 5.354,1.063 5.594,0.313 5.594,0.313 5.719,0.313 false 0.583,0.302 1.927,0.521 1.344,0.219 10 false Angular Ball Bearing 2.781,0.083 4.135,0.313 1.354,0.229 10 false Counter Drive Gear 5.76,0.208 7.135,0.406 1.375,0.198 10 false Elongated Openings 5.125,2.448 6.438,2.677 1.313,0.229 10 false Counter Drive Gear



j.

Clutch and Brake Pistons

i.

Two types of pistons are used, a non-split piston that acts in the push direction for the No. 1 clutch (C1) operation, and a split piston that acts in the pull direction for the No. 2 clutch (C2) operation. These two types of pistons contribute to making the entire clutch structure compact.


ii.

When the split piston operates, clutch drag occurs due to backlash caused by the divided portion of the piston. However, by fitting springs on the piston circumference, such backlash is restrained and the occurrence of clutch drag is minimized.


iii.

By setting the piston for the No. 3 brake (B3) operation around the counter drive gear, the brake structure has been made more compact.

X135998E01
0.531,2.052 0.667,2.052 0.667,2.052 0.896,1.719 true 1.438,2.594 1.708,2.594 1.708,2.594 1.74,1.677 true 1.844,3.052 2.146,3.052 2.146,3.052 3.01,2.635 true 3.167,1.583 3.167,2.073 true 3.615,0.813 3.479,0.813 3.479,0.813 3.479,2.292 true 4.031,1.021 3.896,1.021 3.896,1.021 3.896,2.313 true 4.385,1.344 4.25,1.344 4.25,1.344 4.063,2.208 true 6.042,0.646 5.906,0.646 5.906,0.646 5.552,2.385 true 6.26,0.969 6.125,0.969 6.125,0.969 5.854,2.24 true 5.354,3.635 5.49,3.635 5.49,3.635 5.5,2.604 true 0.083,1.948 0.656,2.177 0.573,0.229 10 false Spring 0.25,2.458 1.427,2.698 1.177,0.24 10 false Piston (Split Type) 2.458,1.406 3.5,1.625 1.042,0.219 10 false Divided Portion 3.646,0.719 3.958,0.917 0.313,0.198 10 false C1 4.063,0.938 4.302,1.104 0.24,0.167 10 false C2 4.448,1.25 5.677,1.469 1.229,0.219 10 false Piston (Split Type) 4.146,3.542 5.354,3.74 1.208,0.198 10 false Counter Drive Gear 6.073,0.552 6.583,0.75 0.51,0.198 10 false Piston 6.302,0.885 6.615,1.083 0.313,0.198 10 false B3 0.656,2.917 1.833,3.156 1.177,0.24 10 false Piston (Split Type)



k.

Transmission Valve Body Assembly

i.

The valve body unit consists of the No. 1 upper, No. 2 upper and lower valve bodies and 7 solenoid valves.

X112347E03
1.063,1.688 0.813,1.01 0.813,1.01 0.552,1.01 false 1.469,1.615 1.125,0.688 1.125,0.688 0.854,0.688 false 2.115,1.531 2.427,0.698 2.427,0.698 2.688,0.698 false 2.542,2.021 2.854,1.188 2.854,1.188 3.115,1.188 false 1.563,2.219 0.927,2.219 false 2.063,2.219 1.75,3.063 1.75,3.063 1.49,3.063 false 2.063,3.01 2.063,3.49 false 3.99,3.427 3.99,3.917 false 5.135,2.156 5.927,2.156 false 5.125,2.49 5.927,2.49 false 5.552,2.875 5.927,2.875 false 4.802,1.604 5.115,0.771 5.115,0.771 5.375,0.771 false 1.552,6.073 1.271,4.635 1.271,4.635 1,4.635 false 2.417,5.51 2.229,4.635 2.229,4.635 1.958,4.635 false 2.969,5.417 2.792,4.625 2.792,4.625 2.604,4.625 false 3.802,6.083 3.479,4.635 3.479,4.635 3.26,4.635 false 4.667,5.552 4.448,4.635 4.448,4.635 4.229,4.635 false 5.052,5.938 5.333,4.625 5.333,4.625 5.552,4.625 false 1.125,7.229 1.125,8.031 false 3.281,7.083 3.281,8.031 false 4.125,7.229 4.125,8.031 false 0.365,0.906 0.563,1.073 0.198,0.167 10 false *1 0.667,0.583 0.865,0.75 0.198,0.167 10 false *2 2.719,0.594 2.917,0.76 0.198,0.167 10 false *3 0.75,2.125 0.948,2.292 0.198,0.167 10 false *4 1.302,2.958 1.5,3.125 0.198,0.167 10 false *5 1.99,3.51 2.188,3.677 0.198,0.167 10 false *6 3.146,1.083 3.344,1.25 0.198,0.167 10 false *7 5.406,0.656 5.604,0.823 0.198,0.167 10 false *8 5.948,2.052 6.146,2.219 0.198,0.167 10 false *9 5.948,2.385 6.198,2.552 0.25,0.167 10 false *10 5.948,2.75 6.146,2.917 0.198,0.167 10 false *9 3.865,3.938 4.115,4.104 0.25,0.167 10 false *11 0.76,4.521 1.01,4.688 0.25,0.167 10 false *12 1.729,4.521 1.979,4.688 0.25,0.167 10 false *13 2.375,4.521 2.625,4.688 0.25,0.167 10 false *14 3.021,4.521 3.271,4.688 0.25,0.167 10 false *16 3.99,4.521 4.24,4.688 0.25,0.167 10 false *18 5.583,4.521 5.833,4.688 0.25,0.167 10 false *19 0.99,8.063 1.24,8.229 0.25,0.167 10 false *10 3.156,8.063 3.406,8.229 0.25,0.167 10 false *15 4,8.063 4.25,8.229 0.25,0.167 10 false *17

Text in Illustration
*1 Shift Solenoid Valve SLU *2 Shift Solenoid Valve SL1
*3 Shift Solenoid Valve SL4 *4 Shift Solenoid Valve SLT
*5 Shift Solenoid Valve SL2 *6 Shift Solenoid Valve SL
*7 Shift Solenoid Valve SL3 *8 No. 2 Upper Valve Body
*9 Plate *10 No. 1 Upper Valve Body
*11 Lower Valve Body *12 Solenoid Modulator Valve
*13 B2 Control Valve *14 B2 Apply Control Valve
*15 Clutch Apply Control Valve *16 Clutch Control Valve
*17 Sequence Valve *18 Primary Regulator Valve
*19 B1 Apply Control Valve - -

X100067E09
1.427,2.542 1.427,3.115 false 2.354,2.115 2.354,2.906 false 2.646,2.292 2.646,3.083 false 3.104,1.844 3.104,2.885 false 4.708,1.365 4.948,0.573 4.948,0.573 5.177,0.573 false 2.427,4.396 1.802,4.396 false 2.302,2.927 2.479,3.094 0.177,0.167 10 false *1 2.594,3.115 2.771,3.281 0.177,0.167 10 false *2 3.042,2.917 3.219,3.083 0.177,0.167 10 false *3 5.208,0.469 5.385,0.635 0.177,0.167 10 false *4 1.344,3.135 1.521,3.302 0.177,0.167 10 false *5 1.615,4.292 1.792,4.458 0.177,0.167 10 false *6 1.906,6.021 2.135,6.208 0.229,0.188 10 false SL 2.167,5.917 2.479,6.104 0.313,0.188 10 false SLT 2.458,5.917 2.771,6.104 0.313,0.188 10 false SLU 2.969,6.365 3.271,6.552 0.302,0.188 10 false SL2 3.542,6.365 3.844,6.552 0.302,0.188 10 false SL1 4.115,6.354 4.417,6.542 0.302,0.188 10 false SL3 4.917,5.781 5.219,5.969 0.302,0.188 10 false SL4

Text in Illustration
*1 Lock-up Control Valve *2 Lock-up Relay Valve
*3 Reverse Sequence Valve *4 Secondary Regulator Valve
*5 No. 2 Upper Valve Body *6 Lower Valve Body



l.

Shift Solenoid Valves SL1, SL2, SL3, SL4, SLU and SLT

i.

In order to provide a hydraulic pressure that is proportional to the current that flows to the solenoid coil, solenoid valves SL1, SL2, SL3, SL4, SLU and SLT linearly control the line pressure and clutch and brake engagement pressure based on the signals from the ECT ECU.


ii.

Solenoid valves SL1, SL2, SL3 and SL4 are large flow linear solenoid valves that can supply more pressure than conventional ones. These solenoid valves control engagement elements by directly regulating the line pressure without using the pressure regulation valve (control valve) or the pressure reduction valve (solenoid modulator valve). Thus, the number of valves and the length of the valve body fluid passage have been reduced, the shifting response has been increased and the shift shock has been minimized.

X106268E07
1.708,5.292 1.458,4.542 1.458,4.542 1.24,4.542 false 1.427,5.188 1.302,4.802 1.302,4.802 1.083,4.802 false 1.667,6.646 1.542,6.25 1.542,6.25 1.313,6.25 false 1.313,6.875 1.25,7.073 1.25,7.073 1.021,7.073 false 1.844,2.719 1.656,2.073 1.656,2.073 1.438,2.073 false 4.854,2.927 4.719,2.167 4.719,2.167 4.531,2.167 false 6.188,1.792 5.74,0.542 5.74,0.542 5.51,0.542 false 5.292,1.958 5.292,1.729 5.292,1.729 5.094,1.729 false 5.219,3.26 5.219,3.677 5.219,3.677 5.083,3.677 false 2.115,1.958 1.958,1.281 1.958,1.281 1.74,1.281 false 0.479,1.177 1.729,1.594 1.25,0.417 10 false Shift Solenoid Valve SL1, SL2, SL3, SL4 0.354,1.979 1.469,2.167 1.115,0.188 10 false Control Pressure 0.604,2.438 1.208,2.875 0.604,0.438 10 false Clutch or Brake 3.427,2.083 4.542,2.271 1.115,0.188 10 false Control Pressure 3.635,2.635 4.25,3.115 0.615,0.479 10 false Clutch or Brake 4.083,1.24 5.365,1.646 1.281,0.406 10 false Shift Solenoid Valve 3.813,0.438 5.5,0.938 1.688,0.5 10 false Pressure Reduction Valve (Solenoid Modulator Valve) 4.052,1.635 5.083,1.823 1.031,0.188 10 false Signal Pressure 5.969,3.271 6.875,3.458 0.906,0.188 10 false Line Pressure 3.427,3.604 5.052,3.969 1.625,0.365 10 false Pressure Regulation Valve (Control Valve) 0.781,3.5 2.552,3.74 1.771,0.24 10 false U660E Automatic Transaxle 0.469,4.427 1.24,4.729 0.771,0.302 10 false Spool Valve 0.635,4.688 1.135,4.844 0.5,0.156 10 false Sleeve 0.99,5.708 3.146,6.083 2.156,0.375 10 false Shift Solenoid Valve SL2 and SL4 0.99,7.333 3.125,7.5 2.135,0.167 10 false Shift Solenoid Valve SL1 and SL3 0.573,6.146 1.365,6.302 0.792,0.156 10 false Spool Valve 0.573,6.958 1.052,7.115 0.479,0.156 10 false Sleeve 3.688,5.615 4.323,6 0.635,0.385 10 false Hydraulic Pressure 5.74,6.771 6.26,6.938 0.521,0.167 10 false Current 2.292,3.021 3.208,3.177 0.917,0.156 10 false Line Pressure 4.323,4.208 6.5,4.51 2.177,0.302 10 false Conventional Automatic Transaxle

X100069E09
1.427,1.323 1.615,0.604 1.615,0.604 1.833,0.604 false 1.354,1.583 1.354,1.885 false 1.292,4.208 1.479,3.49 1.479,3.49 1.688,3.49 false 1.208,4.427 1.208,4.729 false 1.865,0.49 2.885,0.677 1.021,0.188 10 false Spool Valve 1.719,3.375 2.74,3.563 1.021,0.188 10 false Spool Valve 1.135,1.885 1.594,2.073 0.458,0.188 10 false Sleeve 1.01,4.75 1.479,4.938 0.469,0.188 10 false Sleeve 1.042,2.25 2.646,2.448 1.604,0.198 10 false Shift Solenoid Valve SLU 1.042,5.146 2.625,5.344 1.583,0.198 10 false Shift Solenoid Valve SLT 3.677,0.927 4.313,1.25 0.635,0.323 10 false Hydraulic Pressure 3.677,3.875 4.313,4.198 0.635,0.323 10 false Hydraulic Pressure 5.313,2.344 5.844,2.531 0.531,0.188 10 false Current 5.021,5.385 5.552,5.573 0.531,0.188 10 false Current

Shift Solenoid Valve Function
SL1 C1 clutch pressure control
SL2 C2 clutch pressure control
SL3 B1 brake pressure control
SL4 B3 brake pressure control
SLU - Lock-up clutch pressure control
- B2 brake pressure control
SLT Line pressure control



m.

Shift Solenoid Valve SL

i.

The solenoid valve SL uses a three-way solenoid valve.


ii.

A filter is provided at the tip of the solenoid valve to further improve operational reliability.

X100070E08
1.479,1.25 1.198,0.698 1.198,0.698 1.031,0.698 true 1.833,0.625 2.021,0.781 0.188,0.156 10 false *3 0.865,1.177 1.052,1.396 0.188,0.219 10 false *1 0.833,0.583 1.031,0.729 0.198,0.146 10 false *2 1.802,1.802 1.99,1.948 0.188,0.146 10 false *4 2.427,2.167 2.625,2.344 0.198,0.177 10 false *a 5.531,2.167 5.719,2.344 0.188,0.177 10 false *b 3.958,1.167 4.146,1.385 0.188,0.219 10 false *1 4.948,0.698 5.135,0.854 0.188,0.156 10 false *3

Text in Illustration
*1 Modulated Pressure *2 Filter
*3 Control Pressure *4 Drain
*a OFF Condition *b ON Condition

Function of Solenoid Valve
Shift Solenoid Valve Type Function
SL 3-way

- Switches the lock-up relay valve.

- Switches the B2 apply control valve and the reverse sequence valve.






OPERATION


a.

Transmission Power Flow

X136309E01
0.417,0.24 0.896,0.802 0.479,0.563 10 false Shift Lever Position 1.146,0.531 1.5,0.75 0.354,0.219 10 false Gear 2.313,0.354 3.333,0.583 1.021,0.229 10 false Solenoid Valve 4.375,0.354 4.927,0.552 0.552,0.198 10 false Clutch 5.542,0.344 6.021,0.552 0.479,0.208 10 false Brake 6.344,0.281 6.927,0.615 0.583,0.333 10 false One-way Clutch 1.104,1.219 1.479,1.396 0.375,0.177 10 false Park 1,1.5 1.531,1.698 0.531,0.198 10 false Reverse 1.021,1.813 1.51,1.99 0.49,0.177 10 false Neutral 1.156,2.125 1.448,2.292 0.292,0.167 10 false 1st 1.167,2.427 1.458,2.615 0.292,0.188 10 false 2nd 1.177,2.729 1.5,2.906 0.323,0.177 10 false 3rd 1.188,3.042 1.448,3.229 0.26,0.188 10 false 4th 1.177,3.344 1.635,3.542 0.458,0.198 10 false 5th 1.167,3.635 1.625,3.833 0.458,0.198 10 false 6th 1.156,3.958 1.469,4.156 0.313,0.198 10 false 1st 1.156,4.26 1.615,4.458 0.458,0.198 10 false 2nd 1.156,4.563 1.615,4.76 0.458,0.198 10 false 3rd 1.167,4.875 1.625,5.073 0.458,0.198 10 false 4th 1.156,5.177 1.615,5.375 0.458,0.198 10 false 5th 1.156,5.469 1.469,5.667 0.313,0.198 10 false 1st 1.156,5.802 1.615,6 0.458,0.198 10 false 2nd 1.167,6.083 1.625,6.281 0.458,0.198 10 false 3rd 1.177,6.396 1.635,6.594 0.458,0.198 10 false 4th 1.156,6.708 1.469,6.906 0.313,0.198 10 false 1st 1.167,6.979 1.625,7.177 0.458,0.198 10 false 2nd 1.167,7.302 1.625,7.5 0.458,0.198 10 false 3rd 1.167,7.583 1.479,7.781 0.313,0.198 10 false 1st 1.156,7.927 1.615,8.125 0.458,0.198 10 false 2nd 1.177,8.198 1.49,8.396 0.313,0.198 10 false 1st 0.573,8.49 0.969,8.667 0.396,0.177 10 false : ON 1.24,8.49 3.271,8.708 2.031,0.219 10 false : In accordance with flex lock-up 3.542,8.49 6.042,8.688 2.5,0.198 10 false : ON while engaging, OFF after engaged

1st Gear (S Mode 1 Range)
X135989E01
2.615,1.448 2.771,0.469 2.771,0.469 2.854,0.469 true 2.677,1.635 2.833,0.708 2.833,0.708 2.917,0.708 true 2.844,1.76 3.01,0.958 3.01,0.958 3.094,0.958 true 4.219,1.552 4.094,1.292 4.094,1.292 3.99,1.292 true 4.427,1.563 4.906,1.229 4.906,1.229 4.99,1.229 true 5.24,1.854 5.24,1.604 5.24,1.604 5.323,1.604 true 4.698,2.021 5.188,2.219 5.188,2.219 5.271,2.219 true 3.5,2.25 4.125,2.448 4.125,2.448 4.208,2.448 true 4.344,2.865 4.563,2.865 true 4.354,3.365 4.573,3.365 true 3.146,3.573 3.25,3.573 3.25,3.573 3.25,3.333 true 2.302,2.833 2.438,2.833 2.438,2.833 2.438,2.365 true 1.833,2.552 1.969,2.552 1.969,2.552 1.969,2.083 true 1.198,2.26 1.333,2.26 1.333,2.26 1.333,1.885 true 1.917,0.49 2.229,0.688 0.313,0.198 10 false F1 2.375,0.531 2.688,0.729 0.313,0.198 10 false B2 2.896,0.375 3.99,0.573 1.094,0.198 10 false Long Pinion Gear 2.969,0.635 4.104,0.844 1.135,0.208 10 false Short Pinion Gear 3.125,0.875 4.167,1.073 1.042,0.198 10 false Front Sun Gear 3.333,1.188 4.042,1.385 0.708,0.198 10 false Ring Gear 4.229,0.531 4.542,0.729 0.313,0.198 10 false B3 4.688,0.521 5,0.719 0.313,0.198 10 false B1 1.479,0.865 1.792,1.063 0.313,0.198 10 false C2 1.479,1.292 1.792,1.49 0.313,0.198 10 false C1 5.052,1.146 5.875,1.323 0.823,0.177 10 false Pinion Gear 5.344,1.51 6.104,1.698 0.76,0.188 10 false Input Shaft 5.302,2.135 6.01,2.333 0.708,0.198 10 false Sun Gear 4.229,2.344 5.5,2.531 1.271,0.188 10 false Counter Drive Gear 4.594,2.771 6.146,2.969 1.552,0.198 10 false Differential Drive Pinion 4.604,3.26 5.375,3.458 0.771,0.198 10 false Ring Gear 1.865,3.479 3.135,3.677 1.271,0.198 10 false Counter Driven Gear 1.646,2.729 2.323,2.917 0.677,0.188 10 false Ring Gear 0.865,2.458 1.823,2.656 0.958,0.198 10 false Rear Sun Gear 0.052,2.167 1.208,2.365 1.156,0.198 10 false Intermediate Shaft

1st Gear (D Position or S Mode)
X135990E01
1.906,0.479 2.219,0.677 0.313,0.198 10 false F1 2.365,0.531 2.677,0.729 0.313,0.198 10 false B2 4.229,0.542 4.542,0.74 0.313,0.198 10 false B3 4.677,0.542 4.99,0.74 0.313,0.198 10 false B1 1.479,0.875 1.792,1.073 0.313,0.198 10 false C2 1.49,1.292 1.802,1.49 0.313,0.198 10 false C1

2nd Gear (D Position or S Mode)
X135991E01
1.24,2.229 1.333,2.229 1.333,2.229 1.333,1.896 true 1.844,2.448 1.938,2.448 1.938,2.448 1.938,2.115 true 2.344,2.698 2.438,2.698 2.438,2.698 2.438,2.365 true 3.135,3.563 3.229,3.563 3.229,3.563 3.229,3.323 true 2.823,0.479 2.719,0.479 2.719,0.479 2.625,1.469 true 2.896,0.729 2.792,0.729 2.792,0.729 2.698,1.625 true 3.083,0.958 2.979,0.958 2.979,0.958 2.885,1.781 true 3.906,1.271 4.042,1.271 4.042,1.271 4.188,1.542 true 4.979,1.188 4.875,1.188 4.875,1.188 4.417,1.563 true 5.375,1.583 5.271,1.583 5.271,1.583 5.271,1.844 true 4.99,2.219 4.885,2.219 4.885,2.219 4.698,1.979 true 3.927,2.469 3.823,2.469 3.823,2.469 3.594,2.135 true 4.344,2.896 4.552,2.896 true 4.344,3.375 4.552,3.375 true 1.906,0.479 2.219,0.677 0.313,0.198 10 false F1 2.375,0.521 2.688,0.719 0.313,0.198 10 false B2 4.229,0.531 4.542,0.729 0.313,0.198 10 false B3 4.667,0.531 4.979,0.729 0.313,0.198 10 false B1 1.49,0.875 1.802,1.073 0.313,0.198 10 false C2 1.49,1.292 1.802,1.49 0.313,0.198 10 false C1 0.094,2.135 1.229,2.333 1.135,0.198 10 false Intermediate Shaft 0.885,2.354 1.844,2.552 0.958,0.198 10 false Rear Sun Gear 1.677,2.594 2.354,2.813 0.677,0.219 10 false Ring Gear 1.854,3.458 3.115,3.667 1.26,0.208 10 false Counter Driven Gear 2.865,0.385 4,0.583 1.135,0.198 10 false Long Pinion Gear 2.927,0.635 4.063,0.833 1.135,0.198 10 false Short Pinion Gear 3.115,0.865 4.135,1.063 1.021,0.198 10 false Front Sun Gear 3.25,1.177 3.958,1.375 0.708,0.198 10 false Ring Gear 5.042,1.104 6.729,1.302 1.688,0.198 10 false Pinion Gear 5.406,1.49 6.135,1.688 0.729,0.198 10 false Input Shaft 5.052,2.135 6.281,2.333 1.229,0.198 10 false Sun Gear 3.969,2.385 6.719,2.583 2.75,0.198 10 false Counter Drive Gear 4.594,2.802 6.063,2.979 1.469,0.177 10 false Differential Drive Pinion 4.594,3.281 5.969,3.479 1.375,0.198 10 false Ring Gear

3rd Gear (D Position or S Mode)
X135992E01
1.917,0.479 2.229,0.677 0.313,0.198 10 false F1 2.354,0.552 2.667,0.75 0.313,0.198 10 false B2 4.24,0.552 4.552,0.75 0.313,0.198 10 false B3 4.677,0.542 4.99,0.74 0.313,0.198 10 false B1 1.479,0.885 1.792,1.083 0.313,0.198 10 false C2 1.5,1.313 1.813,1.51 0.313,0.198 10 false C1

4th Gear (D Position or S Mode)
X135993E01
1.552,2.198 1.656,2.198 1.656,2.198 1.656,1.896 true 1.875,2.479 1.979,2.479 1.979,2.479 1.979,2.083 true 2.333,2.76 2.438,2.76 2.438,2.76 2.438,2.365 true 3.167,3.573 3.271,3.573 3.271,3.573 3.271,3.333 true 4.344,2.896 4.531,2.896 true 4.344,3.375 4.531,3.375 true 2.615,1.469 2.76,0.51 2.76,0.51 2.833,0.51 true 2.698,1.615 2.823,0.729 2.823,0.729 2.896,0.729 true 2.854,1.771 2.958,1.042 2.958,1.042 3.031,1.042 true 4.219,1.542 4.146,1.281 4.146,1.281 4.063,1.281 true 4.417,1.563 4.844,1.198 4.844,1.198 4.927,1.198 true 5.25,1.865 5.25,1.625 5.25,1.625 5.333,1.625 true 4.688,1.99 4.927,2.198 4.927,2.198 5.01,2.198 true 3.563,2.146 3.865,2.448 3.865,2.448 3.948,2.448 true 1.906,0.479 2.219,0.677 0.313,0.198 10 false F1 2.375,0.531 2.688,0.729 0.313,0.198 10 false B2 1.49,0.875 1.802,1.073 0.313,0.198 10 false C2 1.49,1.302 1.802,1.5 0.313,0.198 10 false C1 2.885,0.417 4.063,0.604 1.177,0.188 10 false Long Pinion Gear 2.917,0.646 4.052,0.854 1.135,0.208 10 false Short Pinion Gear 3.052,0.948 4.135,1.156 1.083,0.208 10 false Front Sun Gear 3.417,1.188 4.083,1.385 0.667,0.198 10 false Ring Gear 4.99,1.104 6.677,1.302 1.688,0.198 10 false Pinion Gear 5.365,1.531 6.115,1.719 0.75,0.188 10 false Input Shaft 5.042,2.094 5.76,2.313 0.719,0.219 10 false Sun Gear 3.99,2.354 6.74,2.552 2.75,0.198 10 false Counter Drive Gear 4.563,2.813 6,2.979 1.438,0.167 10 false Differential Drive Pinion 4.563,3.281 5.313,3.469 0.75,0.188 10 false Ring Gear 1.875,3.479 3.135,3.667 1.26,0.188 10 false Counter Driven Gear 1.677,2.667 2.354,2.865 0.677,0.198 10 false Ring Gear 0.917,2.375 1.896,2.573 0.979,0.198 10 false Rear Sun Gear 0.052,2.094 1.521,2.302 1.469,0.208 10 false Intermediate Shaft Rear 4.229,0.542 4.542,0.74 0.313,0.198 10 false B3 4.667,0.542 4.979,0.74 0.313,0.198 10 false B1

5th Gear (D Position or S Mode)
X135994E01
1.906,0.479 2.219,0.677 0.313,0.198 10 false F1 2.375,0.542 2.688,0.74 0.313,0.198 10 false B2 4.24,0.542 4.552,0.74 0.313,0.198 10 false B3 4.698,0.542 5.01,0.74 0.313,0.198 10 false B1 1.49,0.875 1.802,1.073 0.313,0.198 10 false C2 1.49,1.292 1.802,1.49 0.313,0.198 10 false C1

6th Gear (D Position or S Mode)
X135995E01
1.885,2.427 1.979,2.427 1.979,2.427 1.979,2.115 true 1.448,2.229 1.542,2.229 1.542,2.229 1.542,1.917 true 2.344,2.667 2.438,2.667 2.438,2.667 2.438,2.354 true 3.146,3.542 3.24,3.542 3.24,3.542 3.24,3.323 true 2.896,0.458 2.813,0.458 2.813,0.458 2.625,1.479 true 2.938,0.76 2.854,0.76 2.854,0.76 2.698,1.615 true 3.104,1.031 3.021,1.031 3.021,1.031 2.875,1.792 true 4.115,1.302 4.208,1.302 4.208,1.302 4.208,1.542 true 4.979,1.313 4.896,1.313 4.896,1.313 4.427,1.563 true 5.323,1.594 5.24,1.594 5.24,1.594 5.24,1.865 true 5,2.177 4.917,2.177 4.917,2.177 4.688,1.99 true 3.948,2.469 3.865,2.469 3.865,2.469 3.531,2.188 true 4.354,2.885 4.531,2.885 true 4.354,3.375 4.531,3.375 true 1.917,0.479 2.229,0.677 0.313,0.198 10 false F1 2.375,0.531 2.688,0.729 0.313,0.198 10 false B2 4.229,0.531 4.542,0.729 0.313,0.198 10 false B3 4.688,0.521 5,0.719 0.313,0.198 10 false B1 1.479,0.875 1.792,1.073 0.313,0.198 10 false C2 1.5,1.302 1.813,1.5 0.313,0.198 10 false C1 0.281,2.135 1.417,2.323 1.135,0.188 10 false Intermediate Shaft 0.917,2.323 1.938,2.51 1.021,0.188 10 false Rear Sun Gear 1.677,2.563 2.354,2.76 0.677,0.198 10 false Ring Gear 1.844,3.438 3.115,3.625 1.271,0.188 10 false Counter Driven Gear 2.948,0.375 4.063,0.573 1.115,0.198 10 false Long Pinion Gear 2.969,0.667 4.104,0.854 1.135,0.188 10 false Short Pinion Gear 3.156,0.948 5.302,1.146 2.146,0.198 10 false Front Sun Gear 3.458,1.208 4.25,1.396 0.792,0.188 10 false Ring Gear 5.052,1.219 6.74,1.417 1.688,0.198 10 false Pinion Gear 5.354,1.5 6.115,1.698 0.76,0.198 10 false Input Shaft 5.052,2.094 6.281,2.292 1.229,0.198 10 false Sun Gear 3.979,2.375 6.729,2.573 2.75,0.198 10 false Counter Drive Gear 4.563,2.792 6.063,2.99 1.5,0.198 10 false Differential Drive Pinion 4.573,3.281 5.948,3.479 1.375,0.198 10 false Ring Gear

Reverse Gear (R Range Position)
X135996E01
1.906,0.469 2.219,0.667 0.313,0.198 10 false F1 2.365,0.531 2.677,0.729 0.313,0.198 10 false B2 4.25,0.552 4.563,0.75 0.313,0.198 10 false B3 4.677,0.542 4.99,0.74 0.313,0.198 10 false B1 1.49,0.875 1.802,1.073 0.313,0.198 10 false C2 1.479,1.292 1.792,1.49 0.313,0.198 10 false C1



FAIL-SAFE


a.

This function minimizes the loss of operability when any abnormality occurs in each sensor or solenoid.

Fail-safe Control List
Malfunction Part Function
Input Turbine Speed Sensor Shifting to only either the 1st or 3rd gear is allowed.
Counter Gear Speed Sensor
·

The counter gear speed is detected through the signals from the skid control ECU (speed sensor signals).

·

Shifting between the 1st to 4th gears is allowed.


ATF Temperature Sensor Shifting between the 1st to 4th gears is allowed.
ECT ECU Power Supply (Voltage is Low) When the vehicle is being driven in 6th gear, the transaxle is fixed in 6th gear. When being driven in any of the 1st to 5th gears, the transaxle is fixed in 5th gear.
CAN Communication Shifting to only either the 1st or 3rd gear is allowed.
Knock Sensor Shifting between the 1st to 4th gears is allowed.
Solenoid Valves SL1, SL2,SL3 and SL4 The current to the failed solenoid valve is cut off and the other solenoid valves with normal operation performs shift control. (Shift controls in fail-safe mode are described in the table. For details, refer to fail-safe control list.)

Normal Solenoid Valve Operation
Gear Position 1st 2nd 3rd 4th 5th 6th
Solenoid Valve SL1 ○ ○ ○ ○ X X
SL2 X X X ○ ○ ○
SL3 X ○ X X X ○
SL4 X X ○ X ○ X

Fail-safe Control List
Solenoid Valve Malfunction Condition Gear Position

*1: Fail-safe control is not actuated when the ON malfunction occurs.

*2: If malfunctions already exist in any of the P, R or N range and a malfunction is detected when the gear is shifted to the 1st gear, the gear position is fixed in the 5th gear. After that, if any of the P, R or N range is selected, the gear is fixed in the 3rd gear position.

*3: The gear is fixed in the neutral position until the vehicle speed reaches a certain speed that enables the transaxle to be shifted.

*4: Shifting to the 5th and 6th gears is prohibited.

SL1 OFF Malfunction (without Fail-safe Control) 1st → N 2nd → N 3rd → N 4th → N 5th 6th
ON Malfunction (without Fail-safe Control)*1 1st 2nd 3rd 4th 5th → 4th 6th → 4th
Fail-safe Control during OFF Malfunction Fixed in 3rd or 5th*2
Fail-safe Control during OFF Malfunction (ATF Pressure Switch1 or 2 Malfunction) Fixed in 3rd or 5th*2
SL2 OFF Malfunction (without Fail-safe Control) 1st 2nd 3rd 4th → 1st 5th → N 6th → N
ON Malfunction (without Fail-safe Control)*1 1st → 4th 2nd → 4th 3rd → 4th 4th 5th 6th
Fail-safe Control during OFF Malfunction 1st 2nd 3rd 3rd*3 3rd*3 3rd*3
Fail-safe Control during OFF Malfunction (ATF Pressure Switch 1 or 2 Malfunction) Fixed in 2nd or 3rd*3
SL3 OFF Malfunction (without Fail-safe Control) 1st 2nd → 1st 3rd 4th 5th 6th → N
ON Malfunction (without Fail-safe Control)*1 1st → 2nd 2nd 3rd 4th 5th 6th
Fail-safe Control during OFF Malfunction 1st 3rd 3rd 4th 5th 5th*3
Fail-safe Control during OFF Malfunction (ATF Pressure Switch 1 or 2 Malfunction) Fixed in 3rd*3
SL4 OFF Malfunction (without Fail-safe Control) 1st 2nd 3rd → 1st 4th 5th → N 6th
ON Malfunction (without Fail-safe Control)*1 3rd 3rd 3rd 4th 5th 5th
Fail-safe Control during OFF Malfunction 1st*4 2nd*4 4th*4 4th*4 6th 6th
Fail-safe Control during OFF Malfunction (ATF Pressure Switch 1 or 2 Malfunction) Fixed in 2nd*3



DIAGNOSIS


a.

When the ECT ECU detects a malfunction, the ECT ECU makes a diagnosis and memorizes the failed section. Furthermore, the check engine warning light in the combination meter illuminates or blinks to inform the driver.


b.

At the same time, the DTCs (Diagnosis Trouble Codes) are stored in memory. The DTCs can be read by connecting an intelligent tester II. For details, see the Previa/Tarago Repair Manual.