Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › from 2016.05
NM24M0E _59 Vehicle Exterior _061701 WINDOW / GLASS _0300969 POWER WINDOW CONTROL SYSTEM UN GENERAL/CONTROL/DETAILS F

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


SYSTEM CONTROL


a.

The power window system has the following functions:

Function Outline Customize

*1: Default setting is OFF

*2: Except models for Australia

Manual-up-and-down The manual-up-and-down function causes the window to open or close while the power window switch is being pulled halfway up or pushed halfway down. The window stops as soon as the switch is released. -
One-touch Auto Up-and-down The one-touch auto up-and-down function enables the windows of all doors to be fully opened or closed at a touch of the power window switch. -
Key Off Operation This function makes it possible to operate the power window for approximately 43 seconds after the power source mode is selected to OFF, if the driver's door and front passenger's door are not opened. -
Jam Protection A jam protection function automatically stops the power window and moves it downward if a foreign object gets jammed in any door window during one-touch auto-up operation or manual-up operation. -
Remote Control The up-and-down operations of the front passenger door window and the rear door windows can be controlled by operating the power window master switch. -
Key-linked Up-and-Down Function When the key is not in the interior detection area, the driver's door is locked, and the key in the driver's door is turned and maintained in the lock direction for 1.5 seconds or more, the main body ECU activates the power window motor to raise all door windows while the key is turned. Similarly, when the driver's door is unlocked, turning and maintaining the driver's door key in the unlock direction for 1.5 seconds or more will cause all door windows to be lowered. *1
Transmitter-linked Up-and-Down Function When the main body ECU receives an unlock signal from the transmitter for longer than 3 seconds, the power window master switch control their power window motors in accordance with the signal to open the windows. *1
Lock Switch-linked Up Function*2 All the windows are closed when the lock switch on the outside door handle is pressed for 3 seconds or more with the key in the detection area and all the doors locked. *1
Power Window Glass Open Warning When the power switch is turned from on (IG) to off and the driver door is opened with the power window glass open, the multi buzzer in the combination meter assembly sounds once. Then, a warning message appears on the multi-information display and the master warning light blinks. -



FUNCTION


a.

JAM PROTECTION FUNCTION

i.

The jam protection function automatically stops the power window and moves it downward if foreign object gets jammed in the door window during one-touch auto-up operation or manual-up operation.


ii.

The mechanism uses Hall IC to detect the door glass position and direction of movement.


iii.

The power window ECU is built into the power window motor assembly.


iv.

The reverse-direction conditions and amount of down movement after jam detection are as follows: The jam protection function operates and lowers the window approximately 50 mm (1.9 in.). After this, if the amount (space) that the door glass is open has not reached approximately 200 mm (7.87 in.), the jam protection function will continue to lower the window until the space is approximately 200 mm (7.87 in.). If the door glass reaches the fully open position before the initial 50 mm (1.9 in.) lowering of the door glass is reached, the jam protection function will stop at that time.


v.

The jammed window detection mechanism consists of a magnet that is provided on the worm gear of the power window motor assembly, the power window ECUs and the Hall IC that are provided on the power window ECU.

Power Window Motor Assembly
Y209815E01
2.094,2.573 2.219,2.573 2.219,2.573 2.469,2.271 true 1.75,0.792 1.875,0.792 1.875,0.792 2.354,1.125 true 2.406,0.24 2.531,0.24 2.531,0.24 2.865,0.615 true 3.417,1.125 3.76,0.271 3.76,0.271 3.885,0.271 true 3.615,1.24 4.24,0.708 4.24,0.708 4.365,0.708 true 4.188,2.146 4.75,2.563 4.75,2.563 4.875,2.563 true 0.833,2.49 2.177,2.708 1.344,0.219 10 false Power Window ECU 0.625,0.698 1.833,0.885 1.208,0.188 10 false Connector Portion 1.073,0.125 2.5,0.313 1.427,0.188 10 false Power Window Motor 3.948,0.188 4.49,0.365 0.542,0.177 10 false Hall IC 4.427,0.604 5.344,0.802 0.917,0.198 10 false Magnet 4.927,2.469 5.76,2.667 0.833,0.198 10 false Worm Gear


vi.

The following two factors are used to determine that jamming has occurred.

1.

The Hall IC converts the changes in the magnetic flux that occur through the rotation of the worm gear into block wave signals and outputs them to the power window ECU.

2.

The power window ECU calculates the speed threshold value of the power window motor in accordance with the window glass position, rough road condition, and various operating conditions at the time the power window motor is started. The power window ECU determines that jamming has occurred if the threshold value is exceeded, and retracts the window glass.

Determination by Hall IC
Y209942E01
0.073,0.979 0.99,1.385 0.917,0.406 10 false Hall IC Output Signal 1.021,2.031 2.375,2.438 1.354,0.406 10 false Power Window Motor 1 Revolution (Normal) 3.906,2.031 6.042,2.396 2.135,0.365 10 false Power Window Motor 1 Revolution (Jammed)

Determination by Power Window Motor Speed
Y209787E01
3.719,0.375 3.792,0.167 3.792,0.167 4.208,0.167 true 0.094,0.146 1.604,0.542 1.51,0.396 10 false Determination by Power Window Motor Speed 1.865,0.365 2.021,0.563 0.156,0.198 10 false 0 1.729,0.625 2.042,0.823 0.313,0.198 10 false ON 1.656,0.854 2.01,1.052 0.354,0.198 10 false OFF 4.219,0.073 5.813,0.281 1.594,0.208 10 false Speed Threshold Value 1.729,1.083 2.042,1.281 0.313,0.198 10 false ON 1.656,1.323 2.01,1.521 0.354,0.198 10 false OFF 0.094,0.604 1.042,0.969 0.948,0.365 10 false Power Window Motor Up 0.094,1.083 1.063,1.479 0.969,0.396 10 false Power Window Motor Down


HINT:
·

If the power window motor assembly and power window regulator assembly are replaced, the window position information stored in the system will be lost, and the system must be initialized. After replacing the above parts, initialize the system by performing the steps described below.

(a)

Set the power source mode to IG-ON, and fully open the driver's window. Continue to hold down the switch for at least 1 second after the window has fully opened*.

(b)

Hold the AUTO switch in the auto up position. Continue to hold the AUTO switch in the auto up position for approximately 1 second after the window has fully closed. The system will memorize the window's fully closed position as the initial position.


·

For details, see the Previa/Tarago Repair Manual.


*: When the window reaches its fully open position, the indicator light will change from flashing to illumination, in order to indicate that the window is in the fully open position. However, this does not indicate that the initialization of the system has been completed.