SYSTEM CONTROL
Rear No. 2 Seat
| Component | Function |
|---|---|
| Stowing Switch | Transmits a stowing operation request signal to the power rear No. 2 seat ECU. |
| Return Switch | Transmits a sitting return operation request signal to the power rear No. 2 seat ECU. |
| Folding Switch | Transmits folding operation and folding return operation request signals to the power rear No. 2 seat ECU. |
| Reclining Switch | Transmits a seatback reclining operation request signal to the power rearNo. 2 seat ECU. |
| 3rd Seat Switch Indicator Light | ·
Illuminates when a stowing or sitting return operation is stopped at the switches. ·
Flashes when a sitting return, stowing, or folding operation is stopped as a result of jam detection. ·
Flashes when the switches are pressed while the operation starting conditions are not being met. |
| Power Rear No. 2 Seat ECU | ·
Performs the operations by receiving the signals that are input by the operation switches and actuating a motor or a release actuator. ·
Sounds the buzzer according to the conditions. |
| Reclining Motor | Performs the reclining operation of the seatback upon receiving a signal from the power rear No. 2 seat ECU during a reclining, folding, or folding return operation. |
| Folding Motor | Performs the sitting return or stowing operation of the seat cushion upon receiving a signal from the power rear No. 2 seat ECU during a sitting return or stowing operation. |
| Fold Lock Switch | Detects the stowing condition of the power rear No. 2 seat by turning OFF when the seat cushion reaches the stowing position. |
| Lock Switch | Turns ON or OFF in accordance with the operation of the seat leg lock mechanism, in order to detect the sitting or stowing condition. |
| Release Actuator | Unlocks the seat leg lock mechanism via a wire. |
| Back Door Courtesy Switch | Detects the open or closed condition of the back door. |
| Combination Meter | Illuminates the 3RD SEAT indicator light in the combination meter under the following conditions: the power rear No. 2 seat ECU is not recognizing the position information of the power rear No. 2 seat; or the power rear No. 2 seat is not in an operation completion position (stowing condition or folding condition) when the ignition switch is ON or the back door is open. |
OPERATION
STANDARD OPERATION
When the power folding seat switch is operated, the power rear No. 2 seat with stowing function operates as shown below while the back door is open and the ignition switch is OFF, or the ignition switch is ON and the shift lever is in the P position.
Operating Switch:
A: Return Side of Stowing/Return Switch
B, C: Stowing Side of Stowing/Return Switch
D: Folding Switch
E: Folding Switch, Reclining Switch or Return Side of Stowing/Return Switch
Sitting Return Operation (A)
If the return side of the stowing/return switch is kept pressed while the power rear No. 2 seat is in the stowing condition, the power rear No. 2 seat ECU will sound the buzzer, which is built into the ECU, twice. At the same time, it will actuate the folding motor, which will cause the power rear No. 2 seat to start its sitting return operation.
When the seat cushion reaches the folding condition, the lock switch turns OFF, causing the seat leg lock mechanism to lock onto the floor. Upon receiving the lock switch OFF signal, the power rear No. 2 seat ECU will stop the power supply to the folding motor, sounds the buzzer twice, and actuates the reclining motor in order to start the folding return operation. When the power rear No. 2 seat ECU determines that the seatback has reached its neutral position, based on the speed of the reclining motor, it will stop the operation. Once the folding return operation starts, the operation will continue even if the return side of the stowing/return switch is released.
If the return side of the stowing/return switch is released in the middle of the operation or if the system detects jamming, the power rear No. 2 seat ECU will stop the operation, illuminate*1 or flash*2 the 3rd seat switch indicator light, and sound the buzzer for 10 seconds*3.
*1: When the operation conditions are not met.
*2: When jamming is detected.
*3: If the return side of the stowing/return switch is operated while the operation conditions are not being met, the 3rd seat switch indicator light will flash, without performing the sitting return operation. At this time, the buzzer will not sound.
Stowing Operation (B, C)
If the stowing side of the stowing/return switch is kept pressed while the power rear No. 2 seat is in the sitting or folding condition, the power rear No. 2 seat ECU will sound a built-in buzzer twice. At the same time, it will actuate the reclining motor, which will cause the seatback to start its stowing operation. *1
When the seatback tilts almost to the folding condition*1, the power rear No. 2 seat ECU actuates the release actuator to unlock the seat leg lock mechanism, and starts the actuation of the folding motor. At this time, the seat leg will separate from the striker, and the lock switch will turn ON simultaneously*2.
When the seat cushion is stowed, the fold lock switch turns OFF. Then, the power rear No. 2 seat ECU stops the power supply to the folding motor. At the same time, it sounds the buzzer twice, and stops the stowing operation.
If the stowing side of the stowing/return switch is released in the middle of the operation or if the system detects jamming, it will stop the operation, illuminate*3 or flash*4 the 3rd seat switch indicator light, and sound the buzzer for 10 seconds*5.
*1: Only during sitting condition.
*2: The reclining operation through the use of the reclining switch is disabled when the lock switch is ON.
*3: When the operation conditions are not met.
*4: When jamming is detected.
*5: If the stowing side of the stowing/return switch is operated while the operation conditions are not being met, the 3rd seat switch indicator light will flash, without performing the stowing operation. At this time, the buzzer will not sound.
Folding Operation and Folding Return Operation (D, E)
If the folding switch is pressed while the power rear No. 2 seat is in the sitting condition, the power rear No. 2 seat ECU will actuate the reclining motor, and the seatback will start its folding operation. When the seatback reaches its operation completion position, the load on the reclining motor increases. When the Hall IC in the reclining motor detects this load fluctuation, the power rear No. 2 seat ECU will stop the supply of power to the reclining motor, in order to stop the folding operation.
In the folding return operation, the power rear No. 2 seat ECU actuates the reclining motor in the opposite direction of the folding operation at the same time the folding switch*1 is pressed. Then, the seatback starts the folding return operation. When the power rear No. 2 seat ECU determines that the seatback has reached its neutral position based on the speed of the reclining motor, it will stop the operation.
If the operation conditions have become invalidated during a folding operation or folding return operation, or if jamming has been detected during operation, the power rear No. 2 seat ECU stops the operation, illuminates*2 or flashes the 3rd seat switch indicator light, and sounds the buzzer for 10 seconds*4.
*1: The reclining switch and the return side of the stowing/return switch can also effect this operation.
*2: When the operation conditions are not met.
*3: When jamming is detected.*3: When jamming is detected.
*4: If the folding switch is operated while the operation conditions are not being met, the 3rd seat switch indicator light flashes 3 times, without performing a folding operation or a folding return operation. At this time, the buzzer will not sound.
JAM DETECTION FUNCTION
If an operation of the power rear No. 2 seat is prevented as a result of a jammed object, the pulse signals of the Hall IC that is installed in the folding motor or the reclining motor will change. Thus, the power rear No. 2 seat ECU determines that jamming has occurred.
If jamming is detected, the operation stops, and the buzzer that is built into the power rear No. 2 seat ECU will sound for 10 seconds. At the same time, the 3rd seat switch indicator light will flash.
WARNING
The 3RD SEAT indicator light in the combination meter illuminates under the following conditions: the power rear No. 2 seat ECU does not recognize the position information of the power rear No. 2 seat; or the power rear No. 2 seat has not reached the operation completion position (stowing condition or folding condition) when the ignition switch is ON or the back door is open.
In this system, the power rear No. 2 seat ECU is equipped with EEPROM. It is initialized before shipment, so usually there is no need to perform initializing operations. However, to prepare for the possibility that initialization might need to be performed again for some reasons, it is possible to change a system that has already been initialized into a non-initialized condition (initialization release condition).
Press and hold the reclining switch (forward).
Put the seat into the folding condition.
When the reclining switch (forward) is pressed and held for 1 second while the seat is in the folding condition, the buzzer sounds and initialization is completed.
If the initialization has not been completed, the indicator light on the combination meter illuminates continuously when the ignition switch is turned ON. If the initialization has been completed, the indicator light turns OFF.
Press and hold the return side of the stowing/return switch.
While pressing the return side of the stowing/return switch, press the folding switch 5 times* within 10 seconds.
If the initialization release conditions are met when the return side of the stowing/return switch has been pressed and held for 10 seconds, then initialization is released.
*: If it is pressed 6 or more times, the release operation is cancelled.