FUNCTION OF MAIN COMPONENTS
The main components of the 2GR-FE engine control system are as follows:
| Component | Outline | Quantity | |
|---|---|---|---|
| Engine ECU | 32-bit CPU | 1 | |
| Air Flow Meter | Hot-wire Type | 1 | |
| Crankshaft Position Sensor (Rotor Teeth) | Pick-up Coil Type (36 - 2) | 1 | |
| Intake VVT Sensor (Rotor Teeth) | MRE (Magnetic Resistance Element) Type (3) | 2 | |
| Exhaust VVT Sensor (Rotor Teeth) | MRE (Magnetic Resistance Element) Type (3) | 2 | |
| Accelerator Pedal Position Sensor | Non-contact Type | 1 | |
| Throttle Position Sensor | Non-contact Type | 1 | |
| Knock Sensor | Built-in Piezoelectric Type (Non-resonant Type/Flat Type) | 2 | |
| Air-fuel Ratio Sensor | (Bank 1, Sensor 1) | Type with Heater (Planar Type) | 1 each |
| (Bank 2, Sensor 1) | |||
| Heated Oxygen Sensor | (Bank 1, Sensor 2) | Type with Heater (Cup Type) | 1 each |
| (Bank 2, Sensor 2) | |||
| Injector | 12-hole Type | 3 | |
SYSTEM CONTROL
The engine control system of the 2GR-FE engine has the following features.
| System | Outline |
|---|---|
|
*: Models with Smart Entry & Start System |
|
| EFI (Electronic Fuel Injection) | An L-type EFI system detects the intake air mass with a hot-wire type air flow meter. |
| ESA (Electronic Spark Advance) | ·
Ignition timing is determined by the engine ECU based on signals from various sensors. The engine ECU corrects ignition timing in response to engine knocking. ·
This system selects the optimal ignition timing in accordance with the signals received from the sensors and sends the (IGT) ignition signal to the igniter. |
| ETCS-i (Electronic Throttle Control System-intelligent) | Optimally controls the throttle valve opening in accordance with the amount of accelerator pedal effort and the condition of the engine and the vehicle. |
| Dual VVT-i (Variable Valve Timing-intelligent) System | Controls the intake and exhaust camshafts to an optimal valve timing in accordance with the engine condition. |
| ACIS (Acoustic Control Induction System) | The intake air passages are switched according to the engine speed and throttle valve opening angle to provided high performance in all speed ranges. |
| Fuel Pump Control | ·
Fuel pump operation is controlled by signals from the engine ECU. ·
The fuel pump is stopped, when the SRS airbag is deployed in a frontal, side, and rear side collision. |
| Air Conditioner Cut-off Control | By turning the air conditioner compressor ON or OFF in accordance with the engine condition, drivability is maintained. |
| Evaporative Emission Control | The engine ECU controls the purge flow of evaporative emissions (HC) in the charcoal canister in accordance with engine conditions. |
| Cooling Fan Control | The cooling fan ECU steplessly controls the speed of the fans in accordance with the water temperature, vehicle speed, engine speed, and air conditioner operating conditions. As a result, the cooling performance is improved. |
| Starter Control (Cranking Hold Function)* | Once the engine switch is pushed, this control continues to operate the starter until the engine is started. |
| Air-fuel Ratio Sensor and Oxygen Sensor Heater Control | Maintains the temperature of the air-fuel ratio sensor or heated oxygen sensor at an appropriate level to increase accuracy of detection of the oxygen concentration in the exhaust gas. |
| Engine Immobilizer | Prohibits fuel delivery and ignition if an attempt is made to start the engine with an invalid key. |
| Diagnosis | When the engine ECU detects a malfunction, the engine ECU diagnoses and memorizes the failed section. |
| Fail-safe | When the engine ECU detects a malfunction, the engine ECU stops or controls the engine according to the data already stored in the memory. |
FUNCTION
ETCS-i (Electronic Throttle Control System-intelligent)
In the conventional throttle body, the throttle valve angle is determined invariably by the amount of the accelerator pedal effort. In contrast, ETCS-i uses the engine ECU to calculate the optimal throttle valve angle that is appropriate for the respective driving condition and uses a throttle control motor to control the angle.
Dual VVT-i (Variable Valve Timing-intelligent) System
The Dual VVT-i system is designed to control the intake and exhaust camshafts within a range of 40° and 35° respectively (of Crankshaft Angle) to provide valve timing that is optimally suited to the engine condition. This improves torque in all the speed ranges as well as increasing fuel economy, and reducing exhaust emissions.
During Idling
| Objective | Effect |
|---|---|
| Eliminating overlap to reduce blow back to the intake side. | ·
Stabilized idling rpm ·
Better fuel economy |
At Light Load
| Objective | Effect |
|---|---|
| Eliminating overlap to reduce blow back to the intake side. | Ensured engine stability |
At Medium Load
| Objective | Effect |
|---|---|
| Increasing overlap increases internal EGR, reducing pumping loss. | ·
Better fuel economy ·
Improved emission control |
In Low to Medium Speed Range with Heavy Load
| Objective | Effect |
|---|---|
| Advancing the intake valve close timing for volumetric efficiency improvement. | Improved torque in low to medium speed range |
In High Speed Range with Heavy Load
| Objective | Effect |
|---|---|
| Retarding the intake valve close timing for volumetric efficiency improvement. | Improved output |
At Low Temperatures
| Objective | Effect |
|---|---|
| Eliminating overlap to reduce blow back to the intake side leads to the lean burning condition, and stabilizes the idling speed at fast idle. | ·
Stabilized fast idle rpm ·
Better fuel economy |
Upon Starting/Stopping the Engine
| Objective | Effect |
|---|---|
| Eliminating overlap to minimize blow back to the intake side. | Improved startability |
ACIS (Acoustic Control Induction System)
The ACIS consists of a bulkhead to divide the intake manifold into 2 stages, and an intake air control valve in the bulkhead which opens and closes to vary the effective length of the intake manifold in accordance with the engine speed and throttle valve opening angle. This increases the power output in all ranges from low to high speed.
Ignition Control
A DIS (Direct Ignition System) is used. The DIS improves the ignition timing accuracy, reduces high-voltage loss, and enhances the overall reliability of the ignition system by eliminating the distributor.The DIS is an independent ignition system which has one ignition coil (with igniter) for each cylinder.
CONSTRUCTION
Air Flow Meter
The compact and lightweight air flow meter, which is a plug-in type, allows a portion of the intake air to flow through the detection area. By directly measuring the mass and the flow rate of the intake air, the high detection precision is achieved and the intake air resistance is reduced.
This air flow meter has a built-in intake air temperature sensor.
| *1 | Intake Air Temperature Sensor | - | - |
| *a | Temperature Sensing Element | *b | Platinum Hot-wire Element |
|
Air Flow | - | - |
Crankshaft Position Sensor
The timing rotor of the crankshaft consists of 34 teeth, with 2 teeth missing. The crankshaft position sensor outputs the crankshaft rotation signals every 10°, and the missing teeth are used to determine the top-dead-center.
| *1 | Timing Rotor | *2 | Crankshaft Position Sensor |
|
Engine Front | - | - |
Intake and Exhaust VVT Sensors
The MRE (Magnetic Resistance Element) type intake and exhaust VVT sensors are used. To detect the camshaft position, a timing rotor that is secured to the camshaft in front of the VVT controller is used to generate 6 (3 Hi Output, 3 Lo Output) pulses for every 2 revolutions of the crankshaft.
| *1 | Intake VVT Sensor (Bank 1) | *2 | Timing Rotor |
| *1 | Exhaust VVT Sensor (Bank 1) | *2 | Timing Rotor |
The MRE type VVT sensor consists of an MRE, a magnet and a sensor. The direction of the magnetic field changes due to the different shapes (protruded and non-protruded portions) of the timing rotor, which passes by the sensor. As a result, the resistance of the MRE changes, and the output voltage to the engine ECU changes to Hi or Lo. The engine ECU detects the camshaft position based on this output voltage.
The differences between the MRE type VVT sensor and the pick-up coil type VVT sensor used on the conventionals model are as follows.
| Item | Sensor Type | |
|---|---|---|
| MRE | Pick-up Coil | |
| Signal Output | Constant digital output starts from low engine speeds. | Analog output changes with the engine speed. |
| Camshaft Position Detection | Detection is made by comparing the NE signals with the Hi/Lo output switch timing due to the protruded/non-protruded portions of the timing rotor, or made based on the number of the input NE signals during Hi/Lo outputs. | Detection is made by comparing the NE signals with the change of waveform that is output when the protruded portion of the timing rotor passes. |
Accelerator Pedal Position Sensor
This non-contact type accelerator pedal position sensor uses a Hall IC, which is mounted on the accelerator pedal arm.
The magnetic yoke is mounted at the base of the accelerator pedal arm. This yoke rotates around the Hall IC in accordance with the amount of effort that is applied to the accelerator pedal. The Hall IC converts the changes in the magnetic flux that occur into electrical signals, and outputs them in the form of accelerator pedal position signals to the engine ECU.
The Hall IC contains two circuits, one for the main signal, and one for the sub signal. It converts the accelerator pedal position (angle) into electric signals that have differing characteristics and outputs them to the engine ECU.
| *1 | Hall IC | *2 | Magnetic Yoke |
| *3 | Accelerator Pedal Arm | - | - |
The inspection method differs from the conventional contact type accelerator pedal position sensor because this non-contact type sensor uses a Hall IC. For details, refer to the Repair Manual.
Throttle Position Sensor
The non-contact type throttle position sensor uses a Hall IC, which is mounted on the throttle body.
The Hall IC is surrounded by a magnetic yoke. The Hall IC converts the changes that occur in the magnetic flux at that time into electrical signals and outputs them in the form of a throttle valve effort to the engine ECU.
The Hall IC contains circuits for the main and sub signals. It converts the throttle valve opening angles into electric signals with two differing characteristics and outputs them to the engine ECU.
| *1 | Throttle Body | *2 | Throttle Position Sensor Portion |
| *3 | Magnetic Yoke | *4 | Hall IC (For Throttle Position Sensor) |
| *a | View from A | *b | Cross Section |
The inspection method differs from the conventional contact type throttle position sensor because this non-contact type sensor uses a Hall IC. For details, refer to the Repair Manual.
Knock Sensor (Flat Type)
In the conventional type knock sensor (resonant type), a vibration plate which has the same resonance point as the knocking frequency of the engine is built in and the vibration in this frequency band can be detected. On the other hand, a flat type knock sensor (non-resonant type) has the ability to detect vibration in a wider frequency band from about 6 kHz to 15 kHz, and has the following features.
The engine knocking frequency will change a bit depending on the engine speed. The flat type knock sensor can detect the vibration even when the engine knocking frequency is changed. Thus the vibration detection ability is increased compared to the conventional type knock sensor, and a more precise ignition timing control is possible.
The flat type knock sensor is installed on the engine through the stud bolt installed on the cylinder block. For this reason, a hole for the stud bolt is running through the center of the sensor.
Inside of the sensor, a steel weight is located on the upper portion and a piezoelectric element is located under the weight through the insulator.
The open/short circuit detection resistor is integrated.
| *1 | Steel Weight | *2 | Insulator |
| *3 | Piezoelectric Element | *4 | Open/Short Circuit Detection Resistor |
| *1 | Piezoelectric Element | *2 | Vibration Plate |
The knocking vibration is transmitted to the steel weight and its inertia applies pressure to the piezoelectric element. The action generates electromotive force.
| *1 | Steel Weight | *2 | Inertia |
| *3 | Piezoelectric Element | - | - |
While the ignition is ON, the open/short circuit detection resistor in the knock sensor and the resistor in the engine ECU keep constant the voltage at the terminal KNK1 of engine. An IC (Integrated Circuit) in the engine ECU is always monitoring the voltage of the terminal KNK1. If the open/short circuit occurs between the knock sensor and the engine ECU, the voltage of the terminal KNK1 will change and the engine ECU detects the open/short circuit and stores DTC (Diagnostic Trouble Code).
These knock sensors are mounted in the specific directions and angles as illustrated. To prevent the right and left bank connectors from being interchanged, make sure to install each sensor in its prescribed direction.
| *1 | Knock Sensor (Bank 1) | *2 | Knock Sensor (Bank 2) |
|
Engine Front | - | - |
Air-fuel Ratio Sensor and Heated Oxygen Sensor
The air-fuel ratio sensor and heated oxygen sensor differ in output characteristics.
Approximately 0.4V is constantly applied to the air-fuel ratio sensor, which outputs an amperage that varies in accordance with the oxygen concentration in the exhaust emission. The engine ECU converts the changes in the output amperage into voltage in order to linearly detect the present air-fuel ratio. The air-fuel ratio sensor data is read out by an intelligent tester II.
The output voltage of the heated oxygen sensor changes in accordance with the oxygen concentration in the exhaust emission. The engine ECU uses this output voltage to determine whether the present air-fuel ratio is richer or leaner than the stoichiometric air-fuel ratio.
The basic construction of the air-fuel ratio sensor and heated oxygen sensor is the same. However, they are divided into the cup type and the planar type, according to the different types of heater construction that are used.
The cup type sensor contains a sensor element that surrounds a heater.
The planar type sensor uses alumina, which excels in heat conductivity and insulation, to integrate a sensor element with a heater, thus realizing the excellent warm-up performance of the sensor.
| *1 | Planar Type Air-fuel Ratio Sensor | *2 | Cup Type Heated Oxygen Sensor |
| *3 | Alumina | *4 | Dilation Layer |
| *5 | Platinum Electrode | *6 | Sensor Element (Zirconia) |
| *7 | Heater | *8 | Atmosphere |
| Sensor Type | Planar Type | Cup Type |
| Warm-up Time | Approx. 10 sec. | Approx. 30 sec. |
Intake Air Control Valve
The intake air control valve, which is provided in the intake air chamber, opens and closes to change the effective length of the intake manifold in 2 stages.
| *1 | Intake Air Control Valve | *2 | Actuator |
Actuator (Motor)
The actuator activates the intake air control valve based on signals from the engine ECU.
Ignition Coil
The DIS provides 6 ignition coils, one for each cylinder. The spark plug cap, which provides contact to the spark plug, is integrated with an ignition coil. Also, an igniter is enclosed to simplify the system.
| *1 | Igniter | *2 | Iron Core |
| *3 | Secondary Coil | *4 | Primary Coil |
| *5 | Plug Cap | - | - |
Spark Plug
Long-reach type spark plugs are used. This type of spark plugs allow the area of the cylinder head to receive the spark plugs to be made thick. Thus, the water jacket can be extended near the combustion chamber, which contributes to cooling performance.
Iridium-tipped spark plugs are used to achieve a 193,000 km (120,000 miles) maintenance interval. By making the center electrode of iridium, the superior ignition performance as platinum-tipped spark plugs is achieved and durability has been increased.
| *1 | Iridium Tip | *2 | Platinum Tip |
| *a | Long-reach Type | *b | Conventional Type |
| *c | Water Jacket | - | - |
OPERATION
ETCS-i (Electronic Throttle Control System-intelligent)
The ETCS-i consists of the following five functions:
Normal Throttle Control (Non-linear Control)
Idle Speed Control
TRC (Traction Control)
VSC (Vehicle Stability Control)
Cruise Control*
*: Models with cruise control system
Normal Throttle Control (Non-linear Control)
The engine ECU controls the throttle to an optimal throttle valve angle that is appropriate for the driving condition such as the amount of the accelerator pedal effort and the engine speed in order to realize excellent throttle control and comfort in all operating ranges.
Idle Speed Control
The engine ECU controls the throttle valve in order to constantly maintain an ideal idle speed.
TRC Throttle Control
As part of the TRC system, the throttle valve is closed by a demand signal from the skid control ECU if an excessive amount of slippage is created at a driving wheel, thus facilitates the vehicle in ensuring excellent vehicle stability and driving force.
VSC Coordination Control
In order to bring the effectiveness of the VSC system control into full play, the throttle valve angle is controlled by effecting a coordination control with the skid control ECU.
Cruise Control (Models with Cruise Control System)
An engine ECU with an integrated cruise control ECU directly actuates the throttle valve for operation of the cruise control.
Dual VVT-i (Variable Valve Timing-intelligent) System
Using the engine speed signal, vehicle speed signal, and the signals from air flow meter, throttle position sensor and water temperature sensor, the engine ECU calculates optimal valve timing for each driving condition and controls the camshaft timing oil control valve. In addition, the engine ECU uses signals from the camshaft position sensor and the crankshaft position sensor to detect the actual valve timing, thus providing feedback control to achieve the target valve timing.
Advance
When the camshaft timing oil control valve is positioned as illustrated below by the advance signals from the engine ECU, the resultant oil pressure is applied to the timing advance side vane chamber to rotate the camshaft in the timing advance direction.
| *1 | Vane | *2 | Engine ECU |
| *a | Rotational Direction | *b | Oil Pressure |
| *c | IN | *d | Drain |
| *1 | Vane | *2 | Engine ECU |
| *a | Rotational Direction | *b | Oil Pressure |
| *c | IN | *d | Drain |
Retard
When the camshaft timing oil control valve is positioned as illustrated below by the retard signals from the engine ECU, the resultant oil pressure is applied to the timing retard side vane chamber to rotate the camshaft in the timing retard direction.
| *1 | Vane | *2 | Engine ECU |
| *a | Rotational Direction | *b | Drain |
| *c | IN | *d | Oil Pressure |
| *1 | Vane | *2 | Engine ECU |
| *a | Rotational Direction | *b | Drain |
| *c | IN | *d | Oil Pressure |
Hold
After reaching the target timing, the valve timing is held by keeping the camshaft timing oil control valve in the neutral position unless the traveling state changes.This adjusts the valve timing at the desired target position and prevents the engine oil from running out when it is unnecessary.
ACIS (Acoustic Control Induction System)
While the engine is running at middle speed under high load, the engine ECU controls the actuator to close the intake air control valve. As a result, the effective length of the intake manifold is lengthened and the intake efficiency, in the medium speed range, is improved due to the dynamic effect of the intake air, thereby increasing power output.
Under any condition except when the engine is running at middle speed under high load, the engine ECU controls the actuator to open the intake air control valve. When the intake air control valve is open, the effective length of the intake manifold is shortened and the peak intake efficiency is shifted to the low-to-high engine speed range, thus providing greater output at low-to-high engine speeds.
Fuel Pump Control
A fuel pump control is used to stop the fuel pump when the airbag is deployed at the front collision. In this system, the airbag deployment signal from the airbag sensor assembly is detected by the engine ECU, which turns OFF the circuit opening relay. After the fuel pump control has been activated, turning the ignition switch (engine switch*) from OFF to ON (IG) cancels the fuel pump control, and the engine can be restarted.
*: Models with Smart Entry & Start System
Cooling Fan Control System
A cooling fan control system is used. To achieve an optimal fan speed in accordance with the water temperature, vehicle speed, engine speed, and air conditioner operating conditions, the engine ECU calculates the proper fan speed and proper fan speed control signals to the cooling fan ECU. Upon receiving the signals from the engine ECU, the cooling fan ECU actuates the fan motors.
As illustrated below, the engine ECU determines the required fan speed by selecting the fastest fan speed from among the following:
(A) Fan speed required by the water temperature
(B) Fan speed required by the air conditioner refrigerant pressure
(C) Fan speed required by the engine speed
(D) Fan speed required by the vehicle speed
Starter Control (Models with Smart Entry & Start System)
Once the engine switch is pushed, this function continues to operate the starter until the engine starts, provided that the brake pedal pressed. This prevents starting failures and the engine from being cranked after the engine has started.
When the engine ECU detects a start signal from the main body ECU, this system monitors the engine speed (NE) signal and continues to operate the starter until it determines that the engine has started. Furthermore, even if the engine ECU detects a start signal from the main body ECU, this system will not operate the starter if the engine ECU has determined that the engine has already started.
If the starter relay (STAR) signal cannot be output because the power supplied to the engine ECU is low, the main body ECU outputs the starter relay (STAR) signal instead to help actuate the starter.
As indicated in the following timing chart, when the engine ECU detects a start signal (STSW) from the main body ECU, the engine ECU outputs the STAR and ACCR signals to the main body ECU. Upon detecting the STAR and ACCR signals from the engine ECU, the main body ECU energizes the starter relay to operate the starter. If the engine is already running, the engine ECU stops the output of the STAR and ACCR signals to the main body ECU. Thus, the main body ECU will not energize the starter relay.
After the starter operates and the engine speed becomes higher than approximately 500 rpm, the engine ECU determines that the engine has started and stops the output of the STAR and ACCR signals to the main body ECU. Thus, the main body ECU will stop the operation of the starter.
If the engine has any failure and does not work, the starter operates as long as its maximum continuous operation time and stops automatically. The maximum continuous operation time is approximately 2 seconds through 25 seconds depending on the water temperature condition. When the water temperature is extremely low, it is approximately 25 seconds and when the engine is warmed up sufficiently, it is approximately 2 seconds.
This system cuts off the current that powers the accessories while the engine is cranking to prevent the accessory illumination from operating intermittently due to the unstable voltage that is associated with the cranking of the engine.
This system has the following protections.
While the engine is running normally, the starter does not operate.
In case the driver keeps pressing the engine switch and the engine successfully started, the engine ECU stops the output of the STAR and ACCR signals when the engine speed becomes higher than 1,200 rpm. Thus, the main body ECU will stop the operation of the starter.
In case the driver keeps pressing the engine switch and the engine does not start, the engine ECU stops the output of the STAR and ACCR signals after 30 seconds have elapsed. Thus, the main body ECU will stop the operation of the starter.
In case the engine ECU cannot detect an engine speed signal while the starter is operating, the engine ECU will immediately stop the output of the STAR and ACCR signals. Thus, the main body ECU will stop the operation of the starter.
FAIL-SAFE
When a malfunction is detected by any of the sensors, there is a possibility of an engine or another malfunction occurring if the engine ECU were to continue to control the engine control system in the normal way. To prevent such a problem, the fail-safe function of the engine ECU either relies on the data stored in memory to allow the engine control system to continue operating, or stops the engine if a hazard is anticipated. For details, refer to the Repair Manual.
Fail-safe of Accelerator Pedal Position Sensor
The accelerator pedal position sensor is comprised of two (main, sub) sensor circuits. If a malfunction occurs in either one of the sensor circuits, the engine ECU detects the abnormal signal by voltage difference between these two sensor circuits and switches to the limp mode. In the limp mode, the remaining circuit is used to calculate the accelerator pedal depressed angle, in order to operate the vehicle under the limp mode control.
If both circuits have a malfunction, the engine ECU detects the abnormal signal by voltage from these two sensor circuits and stops the throttle control. At this time, the vehicle can be driven within its idling range.
Fail-safe of Throttle Position Sensor
The throttle position sensor is comprised of two (main, sub) sensor circuits. If a malfunction occurs in either one or both of the sensor circuits, the engine ECU detects the abnormal signal by voltage difference between these two sensor circuits, cuts off the current to the throttle control motor, and switches to the limp mode. Then, the force of the return spring causes the throttle valve to return and stay at the prescribed opening. At this time, the vehicle can be driven in the limp mode while the engine output is regulated through the control of the fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator opening.
The same control as above is effected if the engine ECU detects a malfunction in the throttle control motor system.
DIAGNOSIS
When the engine ECU detects a malfunction, the engine ECU makes a diagnosis and memorizes the failed section. Furthermore, the check engine warning light in the combination meter illuminates or blinks to inform the driver.
The engine ECU will also store the DTCs (Diagnostic Trouble Codes) of the malfunctions.
The DTCs can be accessed by the use of the intelligent tester II.
All the DTCs have been made to correspond to the SAE controlled codes. Some of the DTCs have been further divided into smaller detection areas than in the past, and new DTCs have been assigned to them. For details, refer to the Repair Manual.
To clear the DTC that is stored in the engine ECU, use the intelligent tester II or disconnect the battery terminal or remove the EFI fuse for 1 minute or longer.