OUTLINE
The 2AZ-FE engine is an in-line, 4-cylinder, 2.4-liter, 16-valve DOHC engine. This engine uses the VVT-i (Variable Valve Timing-intelligent) system, DIS (Direct Ignition System), ETCS-i (Electronic Throttle Control System-intelligent). It has been developed to realize high performance, quietness, fuel economy and clean emission.
SPECIFICATIONS
|
*1: Emission regulations differ depending on the specifications of the vehicle. *2: Weight shows the figure with oil and water fully filled. |
||||
| Engine | 2AZ-FE | |||
| No. of Cyls. & Arrangement | 4-cylinder, In-line | |||
| Valve Mechanism | 16-valve DOHC, Chain Drive
(With VVT-i) |
|||
| Combustion Chamber | Pentroof Type | |||
| Manifolds | Cross-flow | |||
| Fuel System | EFI | |||
| Ignition System | DIS | |||
| Displacement | cm3 (cu. in.) | 2362 (144.2) | ||
| Bore X Stroke | mm (in.) | 88.5 x 96.0 (3.48 x 3.78) | ||
| Compression Ratio | 9.8 : 1 | |||
| Max. Output (EEC) | kW@rpm | 125@6000 | ||
| Max. Torque (EEC) | N*m@rpm | 224@4000 | ||
| Valve Timing | Intake | Open | 3° to 43° BTDC | |
| Close | 65° to 25° ABDC | |||
| Exhaust | Open | 45° BBDC | ||
| Close | 3° ATDC | |||
| Firing Order | 1 - 3 - 4 - 2 | |||
| Research Octane Number | 91 or higher | |||
| Oil Grade | API SL, SM, SN or ILSAC | |||
| Oil Capacity | Dry | Liters (US qts, Imp. qts) | 5.0 (5.3, 4.4) | |
| With Oil Filter | Liters (US qts, Imp. qts) | 4.3 (4.5, 3.8) | ||
| Without Oil Filter | Liters (US qts, Imp. qts) | 4.1 (3.8, 3.1) | ||
| Emission Regulation*1 | EURO IV, EURO V | |||
| Engine Service Mass*2 (Reference) | kg (lb) | 129 (284.4) | ||
MAIN FEATURES
The 2AZ-FE engine has achieved the following performance through the use of the items listed below.
(1) High performance and reliability
(2) Low noise and vibration
(3) Lightweight and compact design
(4) Good serviceability
(5) Clean emissions and fuel economy
| Section | Item | (1) | (2) | (3) | (4) | (5) |
|---|---|---|---|---|---|---|
| Engine Proper | The cylinder block made of aluminum alloy along with the magnesium alloy die-cast cylinder head is used. | ○ | ||||
| The taper squish shape is used for the combustion chamber. | ○ | ○ | ||||
| The resin gear balance shaft is used. | ○ | ○ | ||||
| Valve Mechanism | The shim-less type valve lifters are used. | ○ | ○ | |||
| The VVT-i system is used. | ○ | ○ | ||||
| Intake and Exhaust System | The intake manifold made of plastic is used. | ○ | ||||
| The linkless-type throttle body is used. | ○ | ○ | ||||
| The thin-wall ceramic TWC (Three-Way Catalytic converter) is used. | ○ | |||||
| Fuel System | The fuel returnless system is used. | ○ | ○ | ○ | ||
| The quick connectors are used to connect the fuel hose with the fuel pipe. | ○ | ○ | ○ | |||
| The 12-hole type fuel injectors with high atomizing performance are used. | ○ | ○ | ||||
| Ignition System | The iridium-tipped spark plugs are used. | ○ | ○ | |||
| Charging System | The segment conductor type alternator is used. | ○ | ○ | ○ | ||
| Starting System | The PS (Planetary reduction-Segment conductor motor) type starter is used. | ○ | ○ | |||
| Engine Control System | The ETCS-i is used. | ○ | ○ | |||
| The DIS (Direct Ignition System) makes ignition timing adjustment unnecessary. | ○ | ○ | ○ | |||
| The non-contact type sensor is used in the throttle position sensor. | ○ | |||||
| The planar type air-fuel ratio sensor is used. | ○ |