CONSTRUCTION
Cylinder Head Cover
Lightweight yet high-strength aluminum cylinder head covers are used.
An oil delivery pipe is installed inside the cylinder head cover. This ensures lubrication to the sliding parts of the roller rocker arm, improving reliability.
| *1 | Oil Delivery Pipe | *2 | Cylinder Head Cover Gasket |
| *3 | Cylinder Head Cover | - | - |
Cylinder Head Gasket
A steel-laminate type cylinder head gasket is used. A shim is used around the cylinder bore of the gasket to help enhance sealing performance and durability.
| *1 | Shim | - | - |
| *a | For Right Bank | *b | For Left Bank |
| *c | A-A Cross Section | - | - |
|
Engine Front | - | - |
Cylinder Head
The cylinder head structure has been simplified by separating the cam journal portion (camshaft housing) from the cylinder head.
The cylinder head, which is made of aluminum, contains a pentroof-type combustion chamber. The spark plug is located in the center of the combustion chamber in order to improve the engine's anti-knocking performance.
The intake ports are on the inside and the exhaust ports are on the outside of the left and right banks respectively.
Upright intake ports are used to improve the intake efficiency.
A taper squish combustion chamber is used to improve anti-knocking performance and intake efficiency. In addition, engine performance and fuel economy have been improved.
The siamese type intake port is used to reduce the overall surface area of the intake port walls. This prevents the fuel from adhering onto the intake port walls, thus reducing HC exhaust emissions.
| *1 | Intake Valve | *2 | Spark Plug Hole |
| *3 | Exhaust Valve | *4 | Camshaft Housing |
| *a | View from Back Side | *b | Intake Side |
| *c | Exhaust Side | *d | A-A Cross Section |
| *e | Taper Squish | *f | Upright Intake Port |
| *a | Siamese Type | *b | Independent Type |
Cylinder Block
The cylinder block is made of aluminum alloy, so it is lightweight.
The cylinder block has a bank angle of 60°, a bank offset of 36.6 mm (1.441 in.) and a bore pitch of 105.5 mm (4.15 in.), resulting in a compact block in its length and width even for its displacement.
Installation bosses of the two knock sensors are located on the inside of left and right banks.
| *a | View from Top Side | *b | Knock Sensor Boss |
A water passage has been provided between the cylinder bores. By allowing the water to flow between the cylinder bores, this construction enables the temperature of the cylinder walls to be kept uniform.
| *a | Water Passage | - | - |
A compact block has been achieved by producing the thin cast-iron liners and cylinder block as a unit. It is not possible to bore the block with this liner.
The liners are the spiny-type, which have been manufactured so that their casting exteriors form large irregular surfaces in order to enhance the adhesion between the liners and the aluminum cylinder block. The enhanced adhesion helps improve heat dissipation, resulting in a lower overall temperature and reduced heat deformation of the cylinder bores.
| *1 | Cylinder Block | *2 | Liner |
| *a | A-A Cross Section | *b | Irregularly shaped outer casting surface of liner |
Piston
The piston is made of aluminum alloy.
The piston head portion uses a taper squish shape to accomplish fuel combustion efficiency.
The piston skirt is coated with resin to reduce the friction loss.
The groove of the top ring is coated with alumite to ensure wear resistance.
By increasing the machining precision of the cylinder bore diameter, the outer diameter of the piston is made into one size.
| *a | Front Mark | *b | Resin Coating |
| *c | Taper Squish Shape | *d | Alumite Coating |
Connecting Rod and Connecting Rod Bearing
Connecting rods that have been forged for high strength are used for weight reduction.
Knock pins are used at the mating surfaces of the bearing caps of the connecting rod to minimize the shifting of the bearing caps during assembly.
The connecting rods and caps are made of high-strength steel for weight reduction.
Nutless-type plastic region tightening bolts are used on the connecting rods for a lighter design.
An aluminum bearing is used for the connecting rod bearings.
The connecting rod bearings are reduced in width to reduce friction.
| *1 | Plastic Region Tightening Bolt | *2 | Knock Pin |
Crankshaft
A crankshaft made of forged steel, which excels in rigidity and wear resistance, is used.
The crankshaft has 4 journals and 5 balance weights.
All pins and journal fillets are IH-finished to maintain adequate strength.
| *1 | No. 1 Journal | *2 | No. 2 Journal |
| *3 | No. 3 Journal | *4 | No. 4 Journal |
| *5 | Balance Weight | - | - |
|
Engine Front | - | - |
Crankshaft Bearing and Crankshaft Bearing Cap
The crankshaft bearing is made of aluminum alloy.
The upper main bearing has an oil groove around its inside circumference.
The lining surface of the crankshaft bearing has been micro-grooved to realize an optimal amount of oil clearance. As a result, cold-engine cranking performance has been improved and engine vibration have been reduced.
The crankshaft bearing caps are tightened using 4 plastic region tightening bolts for each journal. In addition, each cap is tightened laterally to improve its reliability.
| *1 | Plastic Region Tightening Bolt | *2 | Crankshaft Bearing Cap |
| *3 | Seal Washer | *4 | Upper Main Bearing |
| *5 | Oil Grooved | *6 | Micro-grooved |
| *7 | Lower Main Bearing | - | - |
Crankshaft Pulley
The rigidity of the crankshaft pulley with its built-in torsional damper rubber reduces noise.
| *1 | Torsional Damper Rubber | - | - |
Oil Pan
The oil pan No. 1 is made of aluminum alloy.
The oil pan No. 2 is made of steel.
The oil pan No. 1 is secured to the cylinder block and the transmission housing, increasing rigidity.
The oil filter case is integrated with the oil pan No. 1.
| *1 | Oil Pan No. 1 | *2 | Oil Pan No. 2 |
| *3 | Oil Filter Case | - | - |
Valve Mechanism
Each cylinder of this engine has 2 intake valves and 2 exhaust valves. Intake and exhaust efficiency is increased due to the larger total port areas.
This engine uses roller rocker arms with built-in needle bearings. This reduces the friction that occurs between the cams and the areas (roller rocker arms) that push the valves down, thus improving fuel economy.
A hydraulic lash adjuster, which maintains a constant zero valve clearance through the use of oil pressure and spring force, is used.
The intake camshafts are driven by the crankshaft via the primary timing chain. The exhaust camshafts are driven by the intake camshaft of the respective bank via the secondary timing chain.
This engine uses a Dual VVT-i (Variable Valve Timing-intelligent) system which controls the intake and exhaust camshafts to provide optimal valve timing according to driving conditions. With this adoption, lower fuel consumption, higher engine performance, and fewer exhaust emissions have been achieved.
| *1 | Intake Camshaft | *2 | Exhaust Camshaft |
| *3 | Secondary Timing Chain | *4 | Primary Timing Chain |
| *5 | Roller Rocker Arm | *6 | Valve Spring Retainer |
| *7 | Valve Spring | *8 | Valve Spring Sheet |
| *9 | Valve | *10 | Valve Guide Bush |
| *11 | Hydraulic Lash Adjuster | - | - |
| *a | Intake VVT-i Operation Range | *b | Exhaust VVT-i Operation Range |
| *c | TDC | *d | BDC |
| *e | Intake Valve Opening Angle | *f | Exhaust Valve Opening Angle |
Camshaft
The camshafts are made of cast iron alloy.
An oil passage is provided on the intake and exhaust camshafts in order to supply engine oil to the VVT-i system.
A VVT-i controller has been installed on the front of the intake and exhaust camshafts to vary the timing of the intake and exhaust valves.
Together with the use of the roller rocker arm, the cam profile has been designed with an indented R (radius). This results in increased valve lift when the valve begins to open and finishes closing, helping to achieve enhanced output performance.
| *1 | No. 1 Camshaft (Intake) | *2 | No. 2 Camshaft (Exhaust) |
| *3 | VVT-i Controller | *4 | Timing Rotor |
| *5 | No. 4 Camshaft (Exhaust) | *6 | No. 3 Camshaft (Intake) |
| *a | Cam with indented R | *b | Indented R portion of cam (Profile) |
Timing Chain and Chain Tensioner
Both the primary and secondary timing chains use roller chains with a pitch of 9.525mm (0.375 in.).
The timing chain is lubricated by an oil jet.
The primary timing chain uses one chain tensioner, and each of the secondary timing chains for the right and left banks uses one timing chain tensioner.
Both the primary and secondary chain tensioners use a spring and oil pressure to maintain proper chain tension at all times. They suppress noise generated by the timing chains.
The primary chain tensioner is the ratchet type with a non-return mechanism.
| *1 | Idle Sprocket | *2 | Secondary Chain Tensioner |
| *3 | Secondary Timing Chain | *4 | Ball |
| *5 | Ball Spring | *6 | Plunger |
| *7 | Main Spring | *8 | Primary Chain Tensioner |
| *9 | Spring | *10 | Cam Spring |
| *11 | Cam | *12 | Chain Slipper |
| *13 | Primary Timing Chain | *14 | Timing Chain Oil Jet |
| *15 | Chain Damper | - | - |
Timing Chain Cover
The timing chain cover has an integrated construction consisting of the cooling system (water pump and water passage) and the lubrication system (oil pump and oil passage). Thus, the number of parts has been reduced for weight reduction.
| *1 | Timing Chain Cover | *2 | Water Pump Gasket |
| *3 | Water Pump | *4 | Water Pump Swirl Chamber |
| *5 | Oil Pump Housing | *6 | Oil Pump Rotor |
| *7 | Oil Pump Chamber | - | - |
| *a | View from Front Side | *b | View from Back Side |
Hydraulic Lash Adjuster
The hydraulic lash adjuster, which is located at the fulcrum of the roller rocker arm, consists primarily of a plunger, plunger spring, check ball, and check ball spring.
The engine oil that is supplied by the cylinder head and the built-in spring actuates the hydraulic lash adjuster. The oil pressure and the spring force that act on the plunger push the roller rocker arm against the cam, in order to adjust the valve clearance that is created during the opening and closing of the valve. As a result, engine noise is reduced.
| *1 | Plunger | *2 | Oil Passage |
| *3 | Check Ball | *4 | Check Ball Spring |
| *5 | Plunger Spring | *6 | Roller Rocker Arm |
| *7 | Hydraulic Lash Adjuster | *8 | Cam |
Valve clearance adjustment is not necessary because a hydraulic lash adjuster is used.
Serpentine Belt Drive System
Accessory components are driven by a serpentine belt consisting of a single V-ribbed belt. It reduces the overall engine length, weight and the number of engine parts.
An automatic tensioner eliminates the need for tension adjustment.
| *1 | Water Pump Pulley | *2 | Crankshaft Pulley |
| *3 | Air Conditioner Compressor Pulley | *4 | Idler Pulley for Automatic Tensioner |
| *5 | Alternator Pulley | *6 | Belt Idler |
Automatic Tensioner
The tension of the V-ribbed belt is properly maintained by the tension spring that is enclosed in the automatic tensioner.
| *1 | Idler Pulley | *2 | Arm |
| *3 | Bracket | *4 | Spring |
| *a | Cross Section | *b | Belt Pulling Direction |
| *c | Belt Tension Direction | *d | Fulcrum |
VVT-i Controller
This controller consists of the housing driven by the timing chain and the vane coupled with the intake and exhaust camshafts.
The intake side uses a VVT-i controller with 3 vanes, and the exhaust side uses one with 4 vanes.
When the engine stops, the intake side VVT-i controller is locked on the most retarded side by the lock pin, and the exhaust side VVT-i controller is locked on the most advanced side. This ensures excellent engine startability.
The oil pressure sent from the advance or retard side path at the intake and exhaust camshafts causes rotation in the VVT-i controller vane circumferential direction to vary the intake valve timing continuously.
An advanced angle assist spring is provided on the exhaust side VVT-i controller. This helps to apply torque in the advanced angle direction so that the vane lock pin securely engages with the housing when the engine stops.
| *1 | Timing Rotor | *2 | Housing |
| *3 | Lock Pin | *4 | Sprocket |
| *5 | Vane (Fixed on Intake Camshaft) | *6 | Intake Camshaft |
| *a | In Operation | *b | At a Stop |
|
Oil Pressure | - | - |
| *1 | Housing | *2 | Advanced Angle Assist Spring |
| *3 | Vane (Fixed on Exhaust Camshaft) | *4 | Lock Pin |
| *5 | Sprocket | *6 | Exhaust Camshaft |
Camshaft Timing Oil Control Valve
This camshaft timing oil control valve controls the spool valve using duty-cycle control from the engine ECU. This allows hydraulic pressure to be applied to the VVT-i controller advanced or retarded side. When the engine is stopped, the camshaft timing oil control valve is in the most retarded position.
| *1 | Sleeve | *2 | Spring |
| *3 | Spool Valve | *4 | Coil |
| *5 | Plunger | - | - |
| *a | To VVT-i Controller (Advanced Side) | *b | To VVT-i Controller (Retarded Side) |
| *c | Drain | *d | Oil Pressure |
The advanced and retarded sides of the exhaust camshaft timing oil control valve are reverse of the intake side.