FUNCTION OF MAIN COMPONENTS
| Item | Outline |
|---|---|
| Main Body ECU (Multiplex Network Body ECU) | Receives various signals and illuminates the daytime lights. |
| Headlight Dimmer Switch Assembly
·
Light Control Switch |
Outputs a light control switch position signal to the main body ECU (multiplex network body ECU). |
| DRL Relay | Supplies power to the daytime lights. |
| Automatic Light Control Sensor | Detects the ambient light level. |
| Parking Brake Switch Assembly | Outputs a parking brake operation signal to the main body ECU (multiplex network body ECU). |
| Component | Function |
|---|---|
| Brake Actuator Assembly
·
Skid Control ECU |
Receives various signals and outputs an emergency brake signal to combination meter assembly. |
| Speed Sensor | Detect the wheel speed of each of the 4 wheels. |
| Yawrate Sensor | Outputs the acceleration information. |
| Stop Light Switch Assembly | Detects when the brake pedal is depressed. |
| Combination Meter Assembly | Receives an emergency brake signal and turns on the hazard warning lights. |
| Hazard Warning Switch | Transmits a hazard warning switch on signal to the combination meter assembly. |
| Item | Outline |
|---|---|
| Headlight Swivel Actuator | Moves the projector headlight (low beam) to the swivel angle calculated by the AFS ECU. |
| Steering Angle Sensor | The AFS ECU receives the steering angle sensor signal and uses this information to calculate the headlight swivel angle. |
| Speed Sensor | The AFS ECU receives the speed sensor signal from the skid control ECU and uses this information to calculate the headlight swivel angle. |
| AFS ECU | ·
The AFS ECU receives various signals, calculates the target swivel angle, and actuates the headlight swivel actuator. ·
When the AFS ECU detects a malfunction, the AFS ECU flashes the AFS OFF indicator light in the combination meter. |
| AFS OFF Switch | The driver can cancel the intelligent AFS control by pressing the AFS OFF switch. When the AFS operation is canceled, the AFS OFF indicator light illuminates in the combination meter. |
| AFS OFF Indicator Light | ·
When the intelligent AFS control is canceled by the AFS OFF switch, it is indicated by the light-up of the AFS OFF indicator light. ·
When the AFS ECU detects a malfunction, the AFS ECU flashes the AFS OFF indicator light. |
SYSTEM CONTROL
Daytime Light
Operating Condition
When all of the following conditions are met, the daytime light is illuminated.
The engine switch is on (IG).
An engine speed signal is input (engine is running).
The headlight dimmer switch assembly is in the AUTO position (and the taillights are not turned on via the automatic light control system).
The parking brake switch assembly is off.
Automatic Headlight Beam Level Control System
Operation
The AFS ECU (models with intelligent AFS) is input the vehicle speed signal from the skid control ECU and the height change signal of the vehicle from the height control sensor.Based on these signals, the AFS ECU (models with intelligent AFS) calculates the vehicle's pitch angle change and controls the actuator in accordance with that change amount, and then operates the reflector of the headlight.
Initial Set Control
When the power source mode is selected to IG-ON, the AFS ECU (models with intelligent AFS) operates the actuator to lower the headlight beams to the lowest end. Then, it returns to the proper position. Thus, AFS ECU (models with intelligent AFS) assesses the position of the headlight beam that forms the reference for control.
Emergency Brake Signal
The activating and deactivating conditions for the emergency brake signal are as shown in the following table:
| Condition | Details |
|---|---|
| Emergency Brake Signal Operating Conditions | When all of the following conditions are met, the emergency brake signal starts operating:
·
Vehicle speed is above 55 km/h (35 mph). ·
Driver is depressing the brake pedal. ·
Emergency braking is detected from the vehicle deceleration. |
| Emergency Brake Signal Ending Conditions | When any of the following conditions is met, the emergency brake signal stops operating:
·
Driver has released the brake pedal. ·
Emergency braking is no longer detected from the vehicle deceleration. ·
Driver has operated the hazard warning switch. |
FUNCTION
Daytime Light
The daytime light system is designed to automatically illuminate the Light Emitting Diode (LED) lights during the daytime to keep the vehicle highly visible to other vehicles.
HID Headlight System
The HID (High Intensity Discharge) headlight system uses a metal halide bulb as its light source for the low beam. Metal halide bulbs have features superior to halogen bulbs.
Metal halide bulbs have the following features.
The light emitted by the bulb is close in color to sunlight.
The light shines ahead over a broader range and further forward, increasing the visibility of the driver.
Consume less power.
This system consists of metal halide bulbs and a light control ECU.
The light control ECU transforms the voltage that is input from the battery to a high voltage of up to max. 20,000 V and applies it to the metal halide bulbs in order to illuminate them.
A fail-safe function is provided as a countermeasure against the high voltage that is generated in case that a problem occurs in the HID headlight system.
Intelligent AFS (Adaptive Front-lighting System)
An intelligent AFS (Adaptive Front-lighting System) is used in order to ensure a wide range of the low beam lighting area and increase visibility during turning by swinging the projector headlight (for low beam) to the inner side of the cornering direction.
The intelligent AFS is mainly comprised of the 2 projector headlights (for low beam), AFS ECU, 2 headlight swivel actuators, steering angle sensor and speed sensors.
The intelligent AFS is controlled by the AFS ECU. The AFS ECU also controls the automatic headlight beam level control system.
The AFS ECU regulates the projector headlights (for low beam) to swing toward the cornering direction inner side as shown in the table below.
| Driving Condition | LHD Model | RHD Model | ||
|---|---|---|---|---|
| Headlight Unit (Low Beam) | Headlight Unit (Low Beam) | |||
| Left | Right | Left | Right | |
| Right Turn | 0 to 5° (to Right) | 0 to 10° (to Right) | 0 to 7.5° (to Right) | 0 to 15° (to Right) |
| Left Turn | 0 to 15° (to Left) | 0 to 7.5° (to Left) | 0 to 10° (to Left) | 0 to 5° (to Left) |
| *1 | Projector Headlight | - | - |
| *A | Models with Intelligent AFS | *B | Models without Intelligent AFS |
| *a | Lighting Area | - | - |
Manual Headlight Beam Level Control System
The headlight beam level can be adjusted from 0 to 5 by operating the headlight beam level control switch. By operating this switch, the driver is able to adjust the lighting position of the headlights to a level that is appropriate for the number of occupants and cargo (laden weight) in the vehicle.
| *1 | Headlight Beam Level Control Switch | - | - |
| *a | 0 | *b | 5 |
Automatic Headlight Beam Level Control System
The automatic headlight beam level control system regulates the orientation of the reflectors of the headlights in relation to the posture of the vehicle that has been detected by sensor. Thus, it is a system that maintains the headlight beams to a constant level while the vehicle is being driven.
| System | Content |
|---|---|
| Headlight Beam Level Control | Reflector is driven up and down by 1 actuator (step motor type). |
| Vehicle Height Detection | The height control sensor detects the amount of change in vehicle height. |
| System Control | The AFS ECU processes the detection value transmitted by the sensor and outputs it in the form of a control signal. |
| Operation in System Abnormal | ·
AFS OFF indicator light flashing ·
System control in fail-safe mode ·
DTC (Diagnostic Trouble Code) output |
Light Reminder System
When the power source mode is changed from the IG-ON to ACC or OFF while the driver's door is open with the taillights turned ON, this system warns the driver that the lights remain ON by sounding the multi buzzer. The multi buzzer is located inside the combination meter.
Automatic Light Control System
This system is controlled by the main body ECU.
When the light control switch is at the AUTO position, the automatic light control sensor detects the ambient light and automatically turns the headlights and taillights ON or OFF accordingly.
The automatic light control sensor is integrated with the solar sensor that is used in the automatic air conditioner system.
Light Auto Turn-off System
The light auto turn-off system is controlled by the main body ECU.
All lights will turn OFF when the light auto turn-off system activates.
The light auto turn-off system activates while the headlights, front fog lights, rear fog lights, or taillights are turned ON, and the power source mode is OFF.
Emergency Brake Signal
The hazard warning lights flash automatically in the case of emergency braking to alert following drivers, thus helping to reduce rear-end accidents.
CONSTRUCTION
HID (High Intensity Discharge) Headlight System
Metal Halide Bulb
Instead of the filament contained in a halogen bulb, a metal halide bulb contains an arc tube, which is filled with xenon gas, mercury, and metal halide.
Intelligent AFS (Adaptive Front-lighting System)
Headlight Unit
Headlight Swivel Actuator
A step motor is used for the headlight swivel motor. The AFS ECU determines the projector headlight (low beam) swivel angle based on the steps (position) of the step motor.
| *1 | Projector Headlight | *2 | Headlight Swivel Actuator
·
Headlight Swivel Motor |
| *a | Step-motor | *b | Gear |
| *c | Output Shaft | *d | Sensor (Hall IC) |
Steering Angle Sensor
This steering angle sensor detects the steering direction and angle, and sends this signal to the AFS ECU.
AFS ECU
General
The AFS ECU judges the steering angle and steering direction based on the steering angle sensor signal. Then, it calculates the swivel angle of projector headlight (for low beam) based on the steering angle information, vehicle speed, and headlight swivel motor position. Then, the AFS ECU outputs control signals to the headlight swivel actuators.
The AFS ECU performs intelligent AFS control when all the following conditions are fulfilled:
The vehicle speed is 10 km/h (6.2 mph) or more (excluding R range).
The steering angle is more than 6°.
The headlight low beam is operating.
The AFS OFF switch is turned OFF.
The intelligent AFS controls the right and left headlight swivel actuators in medium and high speeds. On the other hand, it controls only one of the headlight swivel actuators (on the cornering direction inner side) in low speed.
The operating conditions for the headlight swivel actuators of the intelligent AFS differ between low speed and medium and high speeds as follows:
| Condition | Control of Headlight Swivel Actuator | |
|---|---|---|
| Activates | Not Activates | |
|
*1: Vehicle speed is less than 30 km/h (18.6 mph). |
||
| Vehicle Speed [km/h (mph)] | 10 or more (6.2 or more) | Less than 5 (Less than 3.1) |
| Steering Angle | More than 6° | 6° or less |
| Condition | Control of Headlight Swivel Actuator | |
|---|---|---|
| Activates | Not Activates | |
|
*2: Vehicle speed is 30 km/h (18.6 mph) or more. |
||
| Vehicle Speed [km/h (mph)] | More than 10, and less than 220
(More than 6.2, and less than 136.7) |
10 or less, or 220 or more
(6.2 or less, or 136.7 or more) |
| Steering Angle | More than 7.5° | 7.5° or less |
The AFS ECU maintains the neutral point memory for the steering angle sensor, even when no power is supplied to the AFS ECU from the battery (for example, when the connector is disconnected from the AFS ECU). However, when no power is supplied to the steering angle sensor, the neutral point memory for the steering angle sensor will be deleted from the AFS ECU. In this case, it is necessary to correct the neutral point for the sensor.
After the power to the steering angle sensor has been restored, drive the vehicle approximately 100 meters (0.06 miles) at a speed of 80 km/h (48 mph) or less in an area where few curves or traffic congestion exists. This enables the AFS ECU to start an automatic correction (AFS ECU initialization) of the steering neutral point in order to automatically detect the neutral position of the steering angle sensor.
In addition, after turning the power on to AFS ECU again, performing AFS OFF switch operation while the engine is running and the shift lever is in P position enables to do forced AFS ECU initialization. For details of the AFS ECU initialization, refer to Repair Manual.
DTC 13 is output when the AFS ECU has not completed the automatic correction of the steering neutral point. The operation of the intelligent AFS is disabled while this DTC is being output.
Initial Set Control
When the power source mode is selected to IG-ON, the AFS ECU drives the headlight swivel motor and moves the projector headlight (for low beam) to the left and right operation limit. Then the projector headlight returns to the proper position. The AFS ECU thus assesses the position of the light beam that forms the reference for control.
Automatic Headlight Beam Level Control System
AFS ECU
The automatic headlight beam level control system is controlled by the AFS ECU in models with intelligent AFS.
Based on the signals that are transmitted by the height control sensor and the skid control ECU, the ECU detects the amount of change in the vehicle height. Based on the detected value, this ECU outputs control signals to the actuator.
Height Control Sensor
The height control sensor detects the amount of change in the vehicle height while the vehicle is being driven, and output this amount in the form of signals to the AFS ECU.
This sensor is located in the left side rear suspension, and its output changes linearly in accordance with the changes in the vehicle height.
Headlight Level Actuators
Based on the signals received from the AFS ECU (models with intelligent AFS), each actuator moves the reflector in the headlight to vary its beam. This actuator uses a step motor to precisely regulate the angle of the reflector.
FAIL-SAFE
HID (High Intensity Discharge) Headlight System
The light control ECU executes the fail-safe actions listed below in accordance with the item that has been detected.
| Item | Outline |
|---|---|
| Detection of Abnormal Input Voltage | ·
If the voltage that is input to the light control ECU deviates from the operating voltage range (9 - 16 V), the light control ECU stops illuminating the headlights, and resumes illuminating the headlights once the voltage reverts to the operating voltage range. ·
However, if the input voltage decreases after the headlights have illuminated, the headlights will remain illuminated until the bulbs are extinguished. |
| Detection of Abnormal Output (Open Circuit or Short Circuit) or Flashing Bulb | If an abnormal condition (open or short circuit) occurs in the voltage that is output by the light control ECU, or if the bulb flashes, the light control ECU stops illuminating the headlights and will maintain this state until the power is reinstated (by turning the headlight control switch from OFF to ON). |
| Detection of Bulb Open | If a bulb is not inserted in its socket, the light control ECU stops generating high voltage until the bulb is inserted correctly and the power is reinstated (by turning the headlight control switch from OFF to ON or switching the power source mode from OFF to IG-ON). |
Intelligent AFS (Adaptive Front-lighting System)
If the AFS ECU detects a malfunction in the intelligent AFS, it will take the actions indicated in the table below.
| Trouble Area | Headlight Swivel Actuator | AFS OFF Indicator Light | |
|---|---|---|---|
| Headlight Swivel Motor | Open, Short and Gear | Actuates the normal side to the neutral position. | Blinks |
| Communication Stop | Commands actuation to the neutral position. | Blinks | |
| Steering Angle Sensor | Commands actuation to the neutral position. | Blinks | |
| Vehicle Speed Sensor | Commands actuation to the neutral position. | Blinks | |
| Height Control Sensor | Commands actuation to the neutral position. | Blinks | |
| Leveling Motor | Commands actuation to the neutral position. | Blinks | |
| EEPROM | Abnormal Zero Point Data | Commands actuation to the neutral position. | Off |
| Abnormal Rear Vehicle Height Data | Blinks | ||
| Correction Value of Zero Point Steering Angle | Commands actuation to the neutral position. | Off | |
| Shift Position | Commands actuation to the neutral position. | Blinks | |
| Continuous Failure of Steering Angle Restoration | Continues the control. | Off | |
Automatic Headlight Beam Level Control System
The AFS ECU (models with intelligent AFS) operates in the fail-safe mode if an abnormal condition such as those listed below has been detected, and blinks the AFS OFF indicator light (models with intelligent AFS).
| Trouble Area | Headlight Level Actuator | Headlight Swivel Actuator | AFS OFF Indicator Light |
|---|---|---|---|
| Vehicle Speed Sensor Signal Malfunction | Continues controlling. | Stops operation after returning to initial position. | Blinks |
| Vehicle Height Signal Malfunction | ·
Stops operation after returning to initial position (Fail at higher than initial position). ·
Stops at current condition (Fail at lower than initial position). |
Stops operation after returning to initial position. | Blinks |
| Steering Angle Sensor Malfunction | Continues controlling. | Stops operation after returning to initial position. | Blinks |
| Leveling Actuator Communication Signal Malfunction | ·
Stops operation after returning to initial position (Fail at higher than initial position). ·
Stops at current condition (Fail at lower than initial position). |
Stops operation after returning to initial position. | Blinks |
| Leveling Actuator Voltage Malfunction | ·
Stops operation after returning to initial position (Fail at higher than initial position). ·
Stops at current condition (Fail at lower than initial position). ·
Stops at current condition when unable to operate. |
Stops operation after returning to initial position. | Blinks |
| Swivel Actuator Communication Signal Malfunction | Lowers by 0.8° than initial position and then re-starts controlling. | Stops operation after returning to initial position. | Blinks |
| Swivel Actuator Action Malfunction | Lowers by 0.8° than initial position and then re-starts controlling. | Stops operation after returning to initial position (Stops at current condition when unable to operate). | Blinks |
| Swivel Actuator Voltage Malfunction | Lowers by 0.8° than initial position and then re-starts controlling. | Blinks | |
| AFS ECU Malfunction | Continues controlling. | Stops operation after returning to initial position. | Off |
DIAGNOSIS
Intelligent AFS (Adaptive Front-lighting System)
If the AFS ECU detects a malfunction in the intelligent AFS, the AFS ECU blinks the AFS OFF indicator light (1 Hz) that is provided in the combination meter in order to alert the driver.
At the same time, DTCs (Diagnostic Trouble Code) are stored in memory.
The diagnostic mode can be acquired by shorting the initialization terminals of the diagnostic connector.
For details, refer to Repair Manual.
Automatic Headlight Beam Level Control System (Models with Intelligent AFS)
When the AFS ECU detects a malfunction in the automatic headlight beam level control system, the AFS ECU sets a DTC (Diagnostic Trouble Code) and stores it in memory.
The DTC can be accessed through the use of the intelligent tester II. For details, refer to Repair Manual.