Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › from 2016.05
NM24M0E _51 Engine / Hybrid System _061824 CRUISE CONTROL _0301287 CRUISE CONTROL SYSTEM UN GENERAL/CONTROL/DETAILS F

CRUISE CONTROL  CRUISE CONTROL SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION


a.

The cruise control has the following functions.

Function Outline

*1: Models with U660E automatic transaxle

*2: Models with U241E automatic transaxle

*3: Models with continuously variable transaxle

*4: LHD models

*5: RHD models

Constant Speed Control The engine ECU compares the actual vehicle speed and the set speed. If the vehicle speed is higher than the set speed, the engine ECU activates the throttle control motor in the throttle closing direction. If the vehicle speed is lower than the set speed, the engine ECU activates the throttle control motor in the throttle opening direction.
Set Control When the cruise control switch is pressed to the SET/- side and released, and the MAIN switch is turned ON, the engine ECU stores the vehicle speed in memory and continues to control the vehicle at that speed.
Coast Control When the cruise control switch is kept pushed to the SET/- side while running in the cruise control mode, the throttle control motor is energized in the throttle closing direction. The vehicle keeps decelerating and the engine ECU stores the vehicle speed when the cruise control switch is released. From then on, the engine ECU controls the vehicle speed at that speed constantly.
Tap-down Control When the difference between the actual vehicle speed and the set speed is less than 5 km/h (3 mph), the set speed can be lowered approximately 1.6 km/h (1 mph) each time by operating the SET/- switch quickly within approximately 0.6 seconds.
Accelerator Control When the cruise control switch is kept pushed to the RES/+ side while running in the cruise control mode, the throttle control motor is energized in the throttle opening direction. The vehicle keeps accelerating and the engine ECU stores the vehicle speed when the cruise control switch is released. From then on, the engine ECU controls the vehicle speed at that speed constantly.
Tap-up Control When the difference between the actual vehicle speed and the set speed is less than 5 km/h (3 mph), the set speed can be increased approximately 1.6 km/h (1 mph) each time by operating the RES/+ switch quickly within approximately 0.6 seconds.
Low Speed Limit Control The low speed limit is the lowest speed that can be set in cruise control mode, and is designed to approximately 40 km/h (25 mph). The cruise control mode cannot be set below that speed. If the vehicle speed drops below that speed while running in the cruise control mode, the cruise control mode is cancelled automatically. However, the cruise control ECU retains the set speed in memory.
High Speed Limit Control The high speed limit is the highest speed that cruise control mode can be set and is designed at approximately 200 km/h (124 mph).
·

The cruise control mode cannot be set if the vehicle speed exceeds the high speed limit.

·

The vehicle will not accelerate when the RES/+ switch is operated if the vehicle speed exceeds the high speed limit.


Manual Cancel Control If any of the following signals is sent to the engine control ECU (integrates cruise control ECU) while the vehicle is running in the cruise control mode, the cruise control mode is cancelled accordingly.
·

Stop light switch ON signal (Depress the brake pedal)

·

D position circuit in park/neutral position switch OFF signal (Move the shift lever from D to N.)

·

When 1st, 2nd or 3rd range is selected in S mode position.*1

·

When 1st, 2nd range is selected in S mode position.*2

·

When 1st, 2nd or 3rd range is selected in M mode position.*3

·

CANCEL switch ON signal

·

MAIN switch OFF signal


Resume Control If the cruise control mode is canceled through a means other than turning OFF the MAIN switch, the cruise control ECU will retain the speed in memory even if the vehicle speed drops below the low speed limit. Therefore, the driver can resume the mode when the vehicle subsequently reaches a speed above the low speed limit.
Automatic Transmission Control When the vehicle is cruising uphill, there is a case where the overdrive function turns OFF depending on the ECT (Electronic Control Transmission) control. After that the engine ECU judges the end of cruising up from the throttle valve angle, the overdrive function will turn ON again. There is a case where the overdrive Function turns OFF during ACC or RES switch control.
Automatic Cancel Control
·

If any of the following conditions occur while the cruise control system is controlling vehicle speed, the speed that is set in memory is cleared and speed control by the cruise control system is canceled.

-

Stop light switch open or short circuit

-

The vehicle speed signal abnormal

-

ETCS-i malfunction

-

Furthermore, the cruise MAIN indicator light blinks until the MAIN switch is turned OFF, and the operation of the cruise control is disabled until the MAIN switch is turned ON again.*4



·

Furthermore, the cruise control indicator will turn off and a message indicating a malfunction will be displayed on the multi-information display until the cruise control system is turned off using the cruise control switch, and the operation of the cruise control is disabled until the cruise control system is turned on again using the ON-OFF button.*5


·

If any of the following conditions occur while the cruise control system is controlling vehicle speed, the speed that is set in memory is cleared and speed control by the cruise control system is canceled.

-

Stop light switch input signal abnormal

-

Cancel circuit malfunction



·

Furthermore, the cruise MAIN indicator light blinks until the MAIN switch is turned OFF, and the operation of the cruise control is disabled until the engine switch is turned OFF again.*4


·

Furthermore, the cruise control indicator will turn off and a message indicating a malfunction will be displayed on the multi-information display until the cruise control system is turned off using the cruise control switch, and the operation of the cruise control is disabled until the engine switch is turned off.*5


When any of the following conditions occurs, the system will cancel the cruise control mode.
·

The vehicle speed drops 16 km/h (9.9 mph) below the set speed in memory. (The set speed will be cleared from memory.)

·

The vehicle speed is below the low speed limit [40 km/h (25 mph)]. (The set speed will be retained in memory.)


Other Cancellation Items While the vehicle is being driven under cruise control mode, cruise control mode will be canceled if the VSC is activated. (The set speed will be retained in memory.)



DIAGNOSIS


a.

If a malfunction occurs in the cruise control system during cruise control operation, the engine ECU actuates the automatic cancel control and blinks the cruise MAIN indicator light to inform the driver of a malfunction. At this time, the engine ECU memorizes the malfunction in the form of a 5-digit Diagnostic Trouble Code (DTC).*

*: LHD models


b.

If a malfunction occurs in the cruise control system during constant speed control operation, the ECM automatically cancels control and turns off the cruise control indicator. At this time, "Check Cruise Control System" is displayed on the multi-information display. The ECM stores the malfunction in the form of a 5-digit Diagnostic Trouble Code (DTC).*

·

The 5-digit DTC can be read by connecting the Global TechStream (GTS) to the DLC3. For details, refer to the Repair Manual.


*: RHD models