Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
NM24M0E _51 Engine / Hybrid System _061727 2GR-FE ENGINE CONTROL _0301071 SFI SYSTEM UN GENERAL/CONTROL/DETAILS F

2GR-FE ENGINE CONTROL  SFI SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS


a.

The main components of the 2GR-FE engine control system are as follows:

Component Outline Quantity
Engine ECU 32-bit CPU 1
Air Flow Meter Hot-wire Type 1
Crankshaft Position Sensor (Rotor Teeth) Pick-up Coil Type (36 - 2) 1
Intake VVT Sensor (Rotor Teeth) MRE (Magnetic Resistance Element) Type (3) 2
Exhaust VVT Sensor (Rotor Teeth) MRE (Magnetic Resistance Element) Type (3) 2
Accelerator Pedal Position Sensor Non-contact Type 1
Throttle Position Sensor Non-contact Type 1
Knock Sensor Built-in Piezoelectric Type (Non-resonant Type/Flat Type) 2
Air-fuel Ratio Sensor (Bank 1, Sensor 1) Type with Heater (Planar Type) 1 each
(Bank 2, Sensor 1)
Heated Oxygen Sensor (Bank 1, Sensor 2) Type with Heater (Cup Type) 1 each
(Bank 2, Sensor 2)
Injector 12-hole Type 3



SYSTEM CONTROL


a.

The engine control system of the 2GR-FE engine has the following features.

System Outline

*: Models with Smart Entry & Start System

EFI (Electronic Fuel Injection) An L-type EFI system detects the intake air mass with a hot-wire type air flow meter.
ESA (Electronic Spark Advance)
·

Ignition timing is determined by the engine ECU based on signals from various sensors. The engine ECU corrects ignition timing in response to engine knocking.

·

This system selects the optimal ignition timing in accordance with the signals received from the sensors and sends the (IGT) ignition signal to the igniter.


ETCS-i (Electronic Throttle Control System-intelligent) Optimally controls the throttle valve opening in accordance with the amount of accelerator pedal effort and the condition of the engine and the vehicle.
Dual VVT-i (Variable Valve Timing-intelligent) System Controls the intake and exhaust camshafts to an optimal valve timing in accordance with the engine condition.
ACIS (Acoustic Control Induction System) The intake air passages are switched according to the engine speed and throttle valve opening angle to provided high performance in all speed ranges.
Fuel Pump Control
·

Fuel pump operation is controlled by signals from the engine ECU.

·

The fuel pump is stopped, when the SRS airbag is deployed in a frontal, side, and rear side collision.


Air Conditioner Cut-off Control By turning the air conditioner compressor ON or OFF in accordance with the engine condition, drivability is maintained.
Evaporative Emission Control The engine ECU controls the purge flow of evaporative emissions (HC) in the charcoal canister in accordance with engine conditions.
Cooling Fan Control The cooling fan ECU steplessly controls the speed of the fans in accordance with the water temperature, vehicle speed, engine speed, and air conditioner operating conditions. As a result, the cooling performance is improved.
Starter Control (Cranking Hold Function)* Once the engine switch is pushed, this control continues to operate the starter until the engine is started.
Air-fuel Ratio Sensor and Oxygen Sensor Heater Control Maintains the temperature of the air-fuel ratio sensor or heated oxygen sensor at an appropriate level to increase accuracy of detection of the oxygen concentration in the exhaust gas.
Engine Immobilizer Prohibits fuel delivery and ignition if an attempt is made to start the engine with an invalid key.
Brake Override System The driving torque is restricted when both the accelerator and brake pedals are depressed. (For the Activation Conditions and Inspection Method, refer to the repair manual)
Diagnosis When the engine ECU detects a malfunction, the engine ECU diagnoses and memorizes the failed section.
Fail-safe When the engine ECU detects a malfunction, the engine ECU stops or controls the engine according to the data already stored in the memory.



FUNCTION


a.

ETCS-i (Electronic Throttle Control System-intelligent)

i.

In the conventional throttle body, the throttle valve angle is determined invariably by the amount of the accelerator pedal effort. In contrast, ETCS-i uses the engine ECU to calculate the optimal throttle valve angle that is appropriate for the respective driving condition and uses a throttle control motor to control the angle.

W135234E01
3.417,0.25 3.75,0.25 3.75,0.25 3.333,0.917 true 4.917,0.354 4.667,0.354 4.667,0.354 4.333,1.021 true 2.729,4.521 2.521,4.521 2.521,4.521 2.427,4.135 true 3.083,3.021 3.927,3.25 0.844,0.229 10 false Engine ECU 1.323,0.333 2.479,0.729 1.156,0.396 10 false Accelerator Pedal Position Sensor 2.563,0.146 3.417,0.406 0.854,0.26 10 false Throttle Valve 4.979,0.26 6.51,0.5 1.531,0.24 10 false Throttle Position Sensor 1.208,2.094 2.156,2.354 0.948,0.26 10 false Air Flow Meter 1.208,2.958 2.115,3.302 0.906,0.344 10 false Cruise Control Switch* 1.271,3.906 2.073,4.302 0.802,0.396 10 false Skid Control ECU 5.198,0.885 6.188,1.292 0.99,0.406 10 false Throttle Control Motor 5.292,3.042 6.094,3.271 0.802,0.229 10 false Ignition Coil 5.26,3.979 6.188,4.198 0.927,0.219 10 false Fuel Injection 2.771,4.417 3.667,4.646 0.896,0.229 10 false CAN (V Bus) 0.083,4.417 2.417,4.635 2.333,0.219 10 false *: Models with Cruise Control System



b.

Dual VVT-i (Variable Valve Timing-intelligent) System

i.

The Dual VVT-i system is designed to control the intake and exhaust camshafts within a range of 40° and 35° respectively (of Crankshaft Angle) to provide valve timing that is optimally suited to the engine condition. This improves torque in all the speed ranges as well as increasing fuel economy, and reducing exhaust emissions.

W135297E01
2.74,0.552 5.188,0.771 2.448,0.219 9 false Exhaust Camshaft Timing OCV* (Bank 1) 2.802,0.833 5.115,1.063 2.313,0.229 9 false Intake Camshaft Timing OCV* (Bank 1) 3.083,1.094 4.833,1.313 1.75,0.219 9 false Exhaust VVT Sensor (Bank 1) 3.406,1.344 5.063,1.563 1.656,0.219 9 false Water Temperature Sensor 3.708,1.552 4.594,1.802 0.885,0.25 6 false Intake Camshaft Timing OCV* (Bank 2) 3.688,1.813 4.563,2.208 0.875,0.396 8 false Exhaust VVT Sensor (Bank 2) 3.583,2.344 4.25,2.719 0.667,0.375 6 false Exhaust Camshaft Timing OCV* (Bank 2) 3.188,2.938 4.458,3.135 1.271,0.198 7 false Intake VVT Sensor (Bank 2) 3.167,3.292 4.813,3.5 1.646,0.208 9 false Crankshaft Position Sensor 3.25,3.667 4.896,3.875 1.646,0.208 9 false Intake VVT Sensor (Bank 1) 4.625,2.625 5.5,2.823 0.875,0.198 10 false Engine ECU 5.563,3.208 6.635,3.417 1.073,0.208 10 false - Air Flow Meter 5.573,3.438 6.719,3.833 1.146,0.396 10 false - Throttle Position Sensor 0.406,4.354 1.667,4.604 1.26,0.25 10 false *: Oil Control Valve

1.

During Idling

W110969E02
3.438,1.563 3.896,1.76 0.458,0.198 10 false BDC 2.729,0.833 3.188,1.031 0.458,0.198 10 false EX 4.281,0.833 4.74,1.031 0.458,0.198 10 false IN 1.833,0.125 3.104,0.385 1.271,0.26 10 false Most Advanced (EX) 4.146,0.125 5.49,0.458 1.344,0.333 10 false Most Retarded (IN) 3.448,0.063 3.906,0.26 0.458,0.198 10 false TDC

Objective Effect
Eliminating overlap to reduce blow back to the intake side.
·

Stabilized idling rpm

·

Better fuel economy



2.

At Light Load

W110970E03
3.438,1.594 3.896,1.76 0.458,0.167 10 false BDC 2.813,0.854 3.063,1.104 0.25,0.25 10 false EX 4.219,0.865 4.469,1.115 0.25,0.25 10 false IN 3.448,0.073 3.865,0.323 0.417,0.25 10 false TDC 1.688,0.146 3.198,0.448 1.51,0.302 10 false To Advanced Side (EX) 4.104,0.146 5.521,0.531 1.417,0.385 10 false To Retarded Side (IN)

Objective Effect
Eliminating overlap to reduce blow back to the intake side. Ensured engine stability

3.

At Medium Load

W110971E03
2.792,0.885 3.104,1.083 0.313,0.198 10 false EX 4.219,0.875 4.531,1.073 0.313,0.198 10 false IN 3.427,1.583 3.792,1.75 0.365,0.167 10 false BDC 3.427,0.073 3.792,0.24 0.365,0.167 10 false TDC 1.802,0.125 3.25,0.417 1.448,0.292 10 false To Advanced Side (IN) 4.073,0.135 5.49,0.396 1.417,0.26 10 false To Retarded Side (EX)

Objective Effect
Increasing overlap increases internal EGR, reducing pumping loss.
·

Better fuel economy

·

Improved emission control



4.

In Low to Medium Speed Range with Heavy Load

W110972E02
4.26,0.792 4.573,0.99 0.313,0.198 10 false IN 2.719,0.802 3.031,1 0.313,0.198 10 false EX 3.406,1.583 3.885,1.75 0.479,0.167 10 false BDC 1.708,1.438 3.115,1.677 1.406,0.24 10 false To Retarded Side (EX) 4.125,1.448 5.542,1.698 1.417,0.25 10 false To Advanced Side (IN) 3.417,0.021 3.896,0.188 0.479,0.167 10 false TDC

Objective Effect
Advancing the intake valve close timing for volumetric efficiency improvement. Improved torque in low to medium speed range

5.

In High Speed Range with Heavy Load

W110973E02
3.417,1.583 3.875,1.781 0.458,0.198 10 false BDC 3.417,0.031 3.875,0.229 0.458,0.198 10 false TDC 2.719,0.781 3.01,0.979 0.292,0.198 10 false EX 4.25,0.781 4.542,0.979 0.292,0.198 10 false IN 1.688,1.417 3.031,1.677 1.344,0.26 10 false To Retarded Side (IN) 4.177,1.427 5.625,1.688 1.448,0.26 10 false To Advanced Side (EX)

Objective Effect
Retarding the intake valve close timing for volumetric efficiency improvement. Improved output

6.

At Low Temperatures

W110974E03
3.438,1.583 3.896,1.781 0.458,0.198 10 false BDC 3.458,0.073 3.917,0.271 0.458,0.198 10 false TDC 2.781,0.844 3.073,1.094 0.292,0.25 10 false EX 4.26,0.844 4.552,1.094 0.292,0.25 10 false IN 1.813,0.188 3.146,0.427 1.333,0.24 10 false Most Advanced (EX) 4.146,0.188 5.438,0.458 1.292,0.271 10 false Most Retarded (IN)

Objective Effect
Eliminating overlap to reduce blow back to the intake side leads to the lean burning condition, and stabilizes the idling speed at fast idle.
·

Stabilized fast idle rpm

·

Better fuel economy



7.

Upon Starting/Stopping the Engine

W110974E04
3.438,1.583 3.896,1.781 0.458,0.198 10 false BDC 3.458,0.083 3.917,0.281 0.458,0.198 10 false TDC 2.771,0.833 3.063,1.083 0.292,0.25 10 false EX 4.271,0.833 4.563,1.083 0.292,0.25 10 false IN 1.74,0.188 3.063,0.427 1.323,0.24 10 false Most Advanced (EX) 4.125,0.188 5.385,0.438 1.26,0.25 10 false Most Retarded (IN)

Objective Effect
Eliminating overlap to minimize blow back to the intake side. Improved startability




c.

ACIS (Acoustic Control Induction System)

i.

The ACIS consists of a bulkhead to divide the intake manifold into 2 stages, and an intake air control valve in the bulkhead which opens and closes to vary the effective length of the intake manifold in accordance with the engine speed and throttle valve opening angle. This increases the power output in all ranges from low to high speed.

W135298E01
2,2.75 2.25,2.75 2.25,2.75 2.667,2.083 true 5.25,1.917 5.917,1.167 5.917,1.167 6.25,1.167 true 3.25,2 4.75,2.75 4.75,2.75 5.25,2.75 true 1.417,0.208 1.906,0.656 0.49,0.448 10 false Engine Speed 1.292,1.906 2.125,2.146 0.833,0.24 10 false Engine ECU 1.396,2.625 2,2.844 0.604,0.219 10 false Actuator 5.302,2.646 6.417,3.021 1.115,0.375 10 false Intake Air Control Valve 6.302,1.063 6.802,1.531 0.5,0.469 10 false Throttle Valve 3.01,0.354 4.448,0.594 1.438,0.24 10 false Throttle Opening Angle



d.

Ignition Control

i.

A DIS (Direct Ignition System) is used. The DIS improves the ignition timing accuracy, reduces high-voltage loss, and enhances the overall reliability of the ignition system by eliminating the distributor.The DIS is an independent ignition system which has one ignition coil (with igniter) for each cylinder.

W135264E01
4.688,0.729 4.885,0.313 4.885,0.313 5.104,0.313 true 1.458,0.979 2.302,1.229 0.844,0.25 10 false VVT Sensors 1.542,1.802 2.229,2.302 0.688,0.5 9 false Crankshaft Position Sensor 1.625,2.802 2.177,3.188 0.552,0.385 10 false Various Sensors 2.469,1.104 2.74,1.302 0.271,0.198 9 false VV2 2.458,0.896 2.729,1.094 0.271,0.198 9 false VV1 2.469,1.833 2.708,2.021 0.24,0.188 9 false NE 2.875,1.792 3.313,2.177 0.438,0.385 9 false Engine ECU 3.385,0.542 3.729,0.719 0.344,0.177 9 false IGT1 3.406,0.99 3.75,1.167 0.344,0.177 9 false IGT2 3.406,1.417 3.75,1.594 0.344,0.177 9 false IGT3 3.406,1.865 3.75,2.042 0.344,0.177 9 false IGT4 3.396,2.292 3.74,2.469 0.344,0.177 9 false IGT5 3.396,2.729 3.74,2.906 0.344,0.177 9 false IGT6 3.406,3.177 3.656,3.354 0.25,0.177 9 false IGF 4.208,0.219 4.438,0.417 0.229,0.198 10 false +B 5.146,0.219 6.719,0.469 1.573,0.25 10 false Ignition Coil (with Igniter) 5.917,0.667 6.844,0.885 0.927,0.219 10 false No. 1 Cylinder 5.917,1.094 6.844,1.313 0.927,0.219 10 false No. 2 Cylinder 5.917,1.542 6.844,1.76 0.927,0.219 10 false No. 3 Cylinder 5.927,1.99 6.854,2.208 0.927,0.219 10 false No. 4 Cylinder 5.927,2.417 6.854,2.635 0.927,0.219 10 false No. 5 Cylinder 5.917,2.865 6.844,3.083 0.927,0.219 10 false No. 6 Cylinder




CONSTRUCTION


a.

Air Flow Meter

i.

The compact and lightweight air flow meter, which is a plug-in type, allows a portion of the intake air to flow through the detection area. By directly measuring the mass and the flow rate of the intake air, the high detection precision is achieved and the intake air resistance is reduced.


ii.

This air flow meter has a built-in intake air temperature sensor.

W135207C01
4.323,1.26 4.573,1.01 4.573,1.01 4.823,1.01 true 1.25,1 2.25,1 true 1.583,1.917 1.917,1.917 1.917,1.917 2.583,1.333 true 4.854,0.906 5.063,1.104 0.208,0.198 10 false *1 1.073,0.885 1.281,1.115 0.208,0.229 10 false *a 1.396,1.802 1.615,2.01 0.219,0.208 10 false *b
*1 Intake Air Temperature Sensor - -
*a Temperature Sensing Element *b Platinum Hot-wire Element
V100135

Air Flow - -




b.

Crankshaft Position Sensor

i.

The timing rotor of the crankshaft consists of 34 teeth, with 2 teeth missing. The crankshaft position sensor outputs the crankshaft rotation signals every 10°, and the missing teeth are used to determine the top-dead-center.

W135309C01
3.417,2.333 3.417,1.917 true 5.333,1.5 4.5,1.5 true 3.354,2.365 3.552,2.583 0.198,0.219 10 false *1 5.375,1.406 5.583,1.615 0.208,0.208 10 false *2
*1 Timing Rotor *2 Crankshaft Position Sensor
V100136

Engine Front - -


W135267E01
3.615,1.417 3.615,0.917 true 2.844,0.167 4.281,0.406 1.438,0.24 10 false Timing Rotor (720°CA) 2.177,1.427 2.667,1.646 0.49,0.219 10 false 10°CA 3.146,1.458 4.219,1.698 1.073,0.24 10 false 2 Teeth Missing



c.

Intake and Exhaust VVT Sensors

i.

The MRE (Magnetic Resistance Element) type intake and exhaust VVT sensors are used. To detect the camshaft position, a timing rotor that is secured to the camshaft in front of the VVT controller is used to generate 6 (3 Hi Output, 3 Lo Output) pulses for every 2 revolutions of the crankshaft.

RH Bank
W135311C01
3.583,1.667 5.083,0.417 5.083,0.417 5.333,0.417 true 2.083,2.167 2.417,2.167 2.417,2.167 2.917,1.25 true 5.365,0.323 5.552,0.521 0.188,0.198 10 false *1 1.906,2.073 2.115,2.271 0.208,0.198 10 false *2
*1 Intake VVT Sensor (Bank 1) *2 Timing Rotor


RH Bank
W135312C01
3.417,0.417 3.833,0.167 3.833,0.167 4.083,0.167 true 1.833,2.333 2.167,2.333 2.167,2.333 3.167,1.667 true 4.115,0.063 4.344,0.25 0.229,0.188 10 false *1 1.646,2.219 1.833,2.406 0.188,0.188 10 false *2
*1 Exhaust VVT Sensor (Bank 1) *2 Timing Rotor


Sensor Output Waveforms
W135313E01
2.354,0.531 4.552,0.802 2.198,0.271 10 false VVT Sensor Signal Plate (720° CA) 1.302,1.792 1.885,2.063 0.583,0.271 10 false 180° CA 2.24,0.99 2.729,1.188 0.49,0.198 10 false 60° CA 2.708,1.833 3.115,2.031 0.406,0.198 8 false 60° CA 3.49,0.979 4.073,1.25 0.583,0.271 10 false 180° CA 4.542,1.802 5.125,2.073 0.583,0.271 10 false 120° CA 5.354,0.969 5.938,1.24 0.583,0.271 10 false 120° CA 2.104,2.396 2.688,2.667 0.583,0.271 10 false 360° CA 4.573,2.427 5.156,2.698 0.583,0.271 10 false 360° CA 1.135,4.26 1.625,4.458 0.49,0.198 10 false 10° CA 0.021,1.375 0.5,1.813 0.479,0.438 10 false VVT Sensor 0.083,2.031 0.365,2.24 0.281,0.208 10 false 0 V 0.052,2.625 0.49,3.073 0.438,0.448 6 false Crankshaft Position Sensor 0.083,3.302 0.365,3.51 0.281,0.208 10 false 0 V


ii.

The MRE type VVT sensor consists of an MRE, a magnet and a sensor. The direction of the magnetic field changes due to the different shapes (protruded and non-protruded portions) of the timing rotor, which passes by the sensor. As a result, the resistance of the MRE changes, and the output voltage to the engine ECU changes to Hi or Lo. The engine ECU detects the camshaft position based on this output voltage.


iii.

The differences between the MRE type VVT sensor and the pick-up coil type VVT sensor used on the conventionals model are as follows.

Item Sensor Type
MRE Pick-up Coil
Signal Output Constant digital output starts from low engine speeds. Analog output changes with the engine speed.
Camshaft Position Detection Detection is made by comparing the NE signals with the Hi/Lo output switch timing due to the protruded/non-protruded portions of the timing rotor, or made based on the number of the input NE signals during Hi/Lo outputs. Detection is made by comparing the NE signals with the change of waveform that is output when the protruded portion of the timing rotor passes.

W100681E36
4.729,3.969 5.219,3.198 5.219,3.198 5.448,3.198 true 4.469,4.75 4.469,5.229 true 1.885,5.542 2.573,5.698 0.688,0.156 10 false MRE Type 4.938,5.542 5.813,5.708 0.875,0.167 10 false Pick-up Type 0.521,3.094 1.042,3.49 0.521,0.396 10 false Engine Speed 3.542,3.094 4.021,3.51 0.479,0.417 10 false Engine Speed 0.521,4.781 1.021,5.146 0.5,0.365 10 false Sensor Output 3.542,4.49 4.042,4.854 0.5,0.365 10 false Sensor Output 2.813,4.302 3.302,4.729 0.49,0.427 10 false Digital Output 5.938,4.229 6.917,4.448 0.979,0.219 10 false Analog Output 4.063,5.24 4.948,5.458 0.885,0.219 10 false No Detecting 5.531,3.104 6.427,3.354 0.896,0.25 10 false No Detecting 4.573,1.052 5.406,1.292 0.833,0.24 10 false Engine ECU 2.177,0.979 2.792,1.354 0.615,0.375 8 false Intake VVT Sensor 0.76,1.625 1.615,1.823 0.854,0.198 10 false Timing Rotor 0.135,0.042 1.385,0.24 1.25,0.198 12 false Wiring Diagram: 0.188,2.479 5.563,2.938 5.375,0.458 12 false MRE Type and Pick-up Coil Type Output Waveform Image Comparison: 3.865,0.625 4.115,0.823 0.25,0.198 10 false VC 3.708,0.948 4.083,1.146 0.375,0.198 10 false VV1+ 3.729,1.271 4.104,1.469 0.375,0.198 10 false VV1- 2.313,1.854 4.104,2.083 1.792,0.229 10 false Intake VVT Sensor (Bank 1)



d.

Accelerator Pedal Position Sensor

i.

This non-contact type accelerator pedal position sensor uses a Hall IC, which is mounted on the accelerator pedal arm.


ii.

The magnetic yoke is mounted at the base of the accelerator pedal arm. This yoke rotates around the Hall IC in accordance with the amount of effort that is applied to the accelerator pedal. The Hall IC converts the changes in the magnetic flux that occur into electrical signals, and outputs them in the form of accelerator pedal position signals to the engine ECU.


iii.

The Hall IC contains two circuits, one for the main signal, and one for the sub signal. It converts the accelerator pedal position (angle) into electric signals that have differing characteristics and outputs them to the engine ECU.

W135229C01
1.948,1.615 3.115,1.615 true 3.781,1.563 4.781,0.896 4.781,0.896 5.198,0.896 true 4.083,2.083 5.083,1.417 5.083,1.417 5.5,1.417 true 1.771,1.521 1.948,1.74 0.177,0.219 10 false *1 5.24,0.781 5.438,1 0.198,0.219 10 false *2 5.542,1.313 5.74,1.5 0.198,0.188 10 false *3
*1 Hall IC *2 Magnetic Yoke
*3 Accelerator Pedal Arm - -


W135219E01
3,0.833 2.833,0.333 2.833,0.333 3,0.333 true 3,1.917 2.917,2.417 2.917,2.417 3.083,2.417 true 1.854,0.031 4.01,0.292 2.156,0.26 10 false Accelerator Pedal Position Sensor 3.083,0.25 3.583,0.49 0.5,0.24 10 false Magnet 3.135,2.323 3.635,2.563 0.5,0.24 10 false Magnet 2.927,1.052 3.156,1.365 0.229,0.313 8 false Hall IC 2.927,1.417 3.156,1.729 0.229,0.313 8 false Hall IC 3.688,0.469 4.042,0.667 0.354,0.198 10 false VPA 3.688,0.781 4.042,0.979 0.354,0.198 10 false EPA 3.677,1.083 4.115,1.271 0.438,0.188 10 false VCPA 3.688,1.323 4.125,1.51 0.438,0.188 10 false VPA2 3.688,1.615 4.125,1.802 0.438,0.188 10 false EPA2 3.688,1.906 4.125,2.094 0.438,0.188 10 false VCP2 4.375,1.198 4.833,1.635 0.458,0.438 10 false Engine ECU

Characteristic of Accelerator Pedal Position Sensor
W135230E01
2.115,0 2.281,0.208 0.167,0.208 10 false V 1.365,0.656 1.885,1.083 0.521,0.427 10 false Output Voltage 1.74,1.396 2.125,1.781 0.385,0.385 10 false Fully Close 4.615,1.385 5.01,1.781 0.396,0.396 10 false Fully Open 2.073,0.146 2.24,0.354 0.167,0.208 10 false 5 2.063,1.26 2.229,1.469 0.167,0.208 10 false 0 2.302,1.552 4.531,1.76 2.229,0.208 10 false Accelerator Pedal Depressed Angle 2.667,0.573 3.073,0.771 0.406,0.198 10 false VPA2 3.417,0.979 3.823,1.177 0.406,0.198 10 false VPA

HINT:

The inspection method differs from the conventional contact type accelerator pedal position sensor because this non-contact type sensor uses a Hall IC. For details, refer to the Repair Manual.




e.

Throttle Position Sensor

i.

The non-contact type throttle position sensor uses a Hall IC, which is mounted on the throttle body.


ii.

The Hall IC is surrounded by a magnetic yoke. The Hall IC converts the changes that occur in the magnetic flux at that time into electrical signals and outputs them in the form of a throttle valve effort to the engine ECU.


iii.

The Hall IC contains circuits for the main and sub signals. It converts the throttle valve opening angles into electric signals with two differing characteristics and outputs them to the engine ECU.

W135239C01
2.667,0.583 3.083,0.25 3.083,0.25 3.25,0.25 true 3.167,1.5 3.583,1.167 3.583,1.167 3.75,1.167 true 4.396,3.073 4.896,2.74 4.896,2.74 5.229,2.74 true 4.385,3.188 5.219,3.188 true 4.417,3.313 5,3.646 5,3.646 5.25,3.646 true 3.292,0.146 3.49,0.344 0.198,0.198 10 false *1 3.792,1.063 4.01,1.271 0.219,0.208 10 false *2 5.271,2.635 5.448,2.833 0.177,0.198 10 false *3 5.271,3.083 5.469,3.313 0.198,0.229 10 false *4 5.052,2.052 5.26,2.281 0.208,0.229 10 false *a 3.646,4.5 3.875,4.708 0.229,0.208 10 false *b 3.531,1.927 3.688,2.125 0.156,0.198 10 false A 5.281,3.542 5.458,3.74 0.177,0.198 10 false *3
*1 Throttle Body *2 Throttle Position Sensor Portion
*3 Magnetic Yoke *4 Hall IC (For Throttle Position Sensor)
*a View from A *b Cross Section


W135220E01
3,0.833 2.833,0.333 2.833,0.333 3,0.333 true 3,1.917 2.833,2.333 2.833,2.333 3,2.333 true 2.167,0.031 3.667,0.24 1.5,0.208 10 false Throttle Position Sensor 3.094,0.271 3.583,0.615 0.49,0.344 8 false Magnetic Yoke 3.083,2.25 3.573,2.594 0.49,0.344 8 false Magnetic Yoke 2.927,1.083 3.156,1.396 0.229,0.313 8 false Hall IC 2.927,1.458 3.156,1.771 0.229,0.313 8 false Hall IC 3.698,0.792 4.135,1 0.438,0.208 10 false VTA1 3.719,1.115 3.917,1.323 0.198,0.208 10 false E 3.708,1.406 3.969,1.615 0.26,0.208 10 false VC 3.708,1.688 4.146,1.896 0.438,0.208 10 false VTA2 4.385,1.208 4.833,1.594 0.448,0.385 10 false Engine ECU

W135221E01
2.188,0.01 2.417,0.219 0.229,0.208 8 false (V) 2.25,0.177 2.396,0.396 0.146,0.219 10 false 5 2.229,1.292 2.375,1.51 0.146,0.219 10 false 0 4.542,1.396 4.844,1.594 0.302,0.198 10 false 90° 2.135,1.583 2.771,1.75 0.635,0.167 8 true Fully Close 4.26,1.583 4.938,1.75 0.677,0.167 8 true Fully Open 2.74,1.406 4.26,1.594 1.521,0.188 8 false Throttle Valve Opening Angle 1.76,0.635 2.24,1.031 0.479,0.396 9 false Output Voltage 2.615,0.365 2.99,0.563 0.375,0.198 9 false VTA2 3.417,0.875 3.792,1.073 0.375,0.198 9 false VTA1

HINT:

The inspection method differs from the conventional contact type throttle position sensor because this non-contact type sensor uses a Hall IC. For details, refer to the Repair Manual.




f.

Knock Sensor (Flat Type)

i.

In the conventional type knock sensor (resonant type), a vibration plate which has the same resonance point as the knocking frequency of the engine is built in and the vibration in this frequency band can be detected. On the other hand, a flat type knock sensor (non-resonant type) has the ability to detect vibration in a wider frequency band from about 6 kHz to 15 kHz, and has the following features.


ii.

The engine knocking frequency will change a bit depending on the engine speed. The flat type knock sensor can detect the vibration even when the engine knocking frequency is changed. Thus the vibration detection ability is increased compared to the conventional type knock sensor, and a more precise ignition timing control is possible.

W135563E01
0.969,0.281 1.729,0.531 0.76,0.25 10 false : Flat Type 0.958,0.531 2.24,0.781 1.281,0.25 10 false : Conventional Type 2.031,0.844 2.281,1.104 0.25,0.26 10 false (V) 1.698,1.531 2.229,1.781 0.531,0.25 10 false Voltage 3.24,2.302 3.969,2.542 0.729,0.24 10 false Frequency 3.719,1.021 3.865,1.24 0.146,0.219 10 false A 3.75,1.823 3.896,2.042 0.146,0.219 10 false B 4.667,2.323 4.979,2.563 0.313,0.24 10 false (Hz) 5.135,0.896 5.333,1.125 0.198,0.229 10 false A: 5.323,0.896 6.479,1.302 1.156,0.406 10 false Detection Band of Conventional Type 5.135,1.469 5.333,1.698 0.198,0.229 10 false B: 5.323,1.469 6.458,1.938 1.135,0.469 10 false Detection Band of Flat Type 2.615,2.521 4.563,2.74 1.948,0.219 10 false Characteristic of Knock Sensor


iii.

The flat type knock sensor is installed on the engine through the stud bolt installed on the cylinder block. For this reason, a hole for the stud bolt is running through the center of the sensor.


iv.

Inside of the sensor, a steel weight is located on the upper portion and a piezoelectric element is located under the weight through the insulator.


v.

The open/short circuit detection resistor is integrated.

Flat Type Knock Sensor (Non-resonant Type)
W135212C01
2,0.417 2.25,0.417 2.25,0.417 2.583,0.833 true 2,0.948 2.5,0.948 true 2,1.375 2.25,1.375 2.25,1.375 2.5,1.042 true 3.75,1.021 4.167,1.521 4.167,1.521 4.417,1.521 true 1.823,0.313 2.031,0.521 0.208,0.208 10 false *1 1.823,0.844 2.031,1.063 0.208,0.219 10 false *2 1.833,1.271 2.021,1.458 0.188,0.188 10 false *3 4.438,1.406 4.625,1.615 0.188,0.208 10 false *4
*1 Steel Weight *2 Insulator
*3 Piezoelectric Element *4 Open/Short Circuit Detection Resistor


Conventional Type Knock Sensor (Resonant Type)
W135213C01
3.75,1.292 4.167,0.708 4.167,0.708 4.5,0.708 true 3.833,1.323 4.25,1.823 4.25,1.823 4.583,1.823 true 4.542,0.604 4.74,0.792 0.198,0.188 10 false *1 4.625,1.719 4.802,1.938 0.177,0.219 10 false *2
*1 Piezoelectric Element *2 Vibration Plate



vi.

The knocking vibration is transmitted to the steel weight and its inertia applies pressure to the piezoelectric element. The action generates electromotive force.

W135216C01
2.75,0.333 3,0.333 3,0.333 3.417,0.833 true 2.792,1 3.458,1 true 2.833,1.333 3,1.333 3,1.333 3.417,1.083 true 2.563,0.24 2.792,0.448 0.229,0.208 10 false *1 2.615,0.896 2.833,1.094 0.219,0.198 10 false *2 2.656,1.24 2.865,1.448 0.208,0.208 10 false *3
*1 Steel Weight *2 Inertia
*3 Piezoelectric Element - -



vii.

While the ignition is ON, the open/short circuit detection resistor in the knock sensor and the resistor in the engine ECU keep constant the voltage at the terminal KNK1 of engine. An IC (Integrated Circuit) in the engine ECU is always monitoring the voltage of the terminal KNK1. If the open/short circuit occurs between the knock sensor and the engine ECU, the voltage of the terminal KNK1 will change and the engine ECU detects the open/short circuit and stores DTC (Diagnostic Trouble Code).

W135215E01
0.5,2.333 0.5,2 0.5,2 1.167,1.75 true 2.083,2.365 2.083,2.031 2.083,2.031 1.917,1.781 true 4.917,0.229 5.781,0.448 0.865,0.219 10 false Engine ECU 1.25,0.979 2.167,1.198 0.917,0.219 10 false Knock Sensor 4.354,0.76 4.615,0.99 0.26,0.229 10 false 5 V 4.583,1.135 5.104,1.354 0.521,0.219 10 false 200 kΩ 6.052,1.542 6.26,1.74 0.208,0.198 10 false IC 2.031,1.688 2.552,1.906 0.521,0.219 10 false 200 kΩ 3.76,1.219 4.177,1.448 0.417,0.229 10 false KNK1 3.719,1.854 4.135,2.083 0.417,0.229 10 false EKNK 0.177,2.365 1,2.75 0.823,0.385 10 false Piezoelectric Element 1.615,2.385 2.771,2.76 1.156,0.375 9 false Open/Short Circuit Detection Resistor

HINT:

These knock sensors are mounted in the specific directions and angles as illustrated. To prevent the right and left bank connectors from being interchanged, make sure to install each sensor in its prescribed direction.

W135296C01
3.167,0.167 3.417,0.167 3.417,0.167 3.667,1 true 5.667,2.167 5.333,2.167 5.333,2.167 4.083,1.333 true 3.01,0.052 3.219,0.24 0.208,0.188 10 false *1 5.719,2.063 5.938,2.26 0.219,0.198 10 false *2
*1 Knock Sensor (Bank 1) *2 Knock Sensor (Bank 2)
V100135

Engine Front - -





g.

Air-fuel Ratio Sensor and Heated Oxygen Sensor

i.

The air-fuel ratio sensor and heated oxygen sensor differ in output characteristics.


ii.

Approximately 0.4V is constantly applied to the air-fuel ratio sensor, which outputs an amperage that varies in accordance with the oxygen concentration in the exhaust emission. The engine ECU converts the changes in the output amperage into voltage in order to linearly detect the present air-fuel ratio. The air-fuel ratio sensor data is read out by an intelligent tester II.


iii.

The output voltage of the heated oxygen sensor changes in accordance with the oxygen concentration in the exhaust emission. The engine ECU uses this output voltage to determine whether the present air-fuel ratio is richer or leaner than the stoichiometric air-fuel ratio.

W135197E01
1.552,0.49 1.958,0.698 0.406,0.208 10 false A1A+ 2.198,1.198 2.667,1.625 0.469,0.427 10 false Engine ECU 5.677,1.25 6.146,1.677 0.469,0.427 10 false Engine ECU 0.031,1.052 0.802,1.5 0.771,0.448 9 false Air-fuel Ratio Sensor 1.51,0.708 1.969,0.917 0.458,0.208 10 false (3.3 V) 1.583,1.646 1.99,1.854 0.406,0.208 10 false A1A- 1.521,1.865 1.979,2.094 0.458,0.229 10 false (2.9 V) 3.729,0.969 4.26,1.531 0.531,0.563 9 false Heated Oxygen Sensor 5.021,0.49 5.427,0.698 0.406,0.208 10 false OX1B 5.052,1.646 5.458,1.854 0.406,0.208 10 false EX1B 1.135,2.469 2.917,2.708 1.781,0.24 10 false Air-fuel Ratio Sensor Circuit 4.51,2.479 6.448,2.708 1.938,0.229 10 false Heated Oxygen Sensor Circuit

W135564E01
4.719,0.344 6.125,0.563 1.406,0.219 10 false : Air-fuel Ratio Sensor 4.719,0.667 6.302,0.885 1.583,0.219 10 false : Heated Oxygen Sensor 4.844,0.958 5.042,1.156 0.198,0.198 10 false 1 4.938,1.708 6.094,2.156 1.156,0.448 10 false Heated Oxygen Sensor Output (V) 0.979,1.656 2.302,2.229 1.323,0.573 10 false Air-fuel Ratio Sensor Data Displayed on Intelligent Tester II 2.042,0.958 2.313,1.177 0.271,0.219 10 false 4.2 2.052,2.719 2.323,2.938 0.271,0.219 10 false 2.2 4.875,2.74 5.156,2.948 0.281,0.208 10 false 0.1 2.323,3.052 2.896,3.365 0.573,0.313 10 false 11(Rich) 3.344,3.063 3.667,3.302 0.323,0.24 10 false 14.7 4.344,3.052 5,3.333 0.656,0.281 10 false 19 (Lean) 3.104,3.406 3.958,3.625 0.854,0.219 10 false Air-fuel Ratio


iv.

The basic construction of the air-fuel ratio sensor and heated oxygen sensor is the same. However, they are divided into the cup type and the planar type, according to the different types of heater construction that are used.


v.

The cup type sensor contains a sensor element that surrounds a heater.


vi.

The planar type sensor uses alumina, which excels in heat conductivity and insulation, to integrate a sensor element with a heater, thus realizing the excellent warm-up performance of the sensor.

W135222C01
0.333,0.25 3.333,3.667 3,3.417 3.833,0.25 6.833,3.667 3,3.417 2.427,1.604 2.594,1.604 2.594,1.604 2.76,2.104 true 2.188,1.813 2.354,1.813 2.354,1.813 2.604,2.229 true 2.208,2.5 2.542,2.5 true 2.281,3.073 2.448,3.073 2.448,3.073 2.615,2.656 true 2.333,3.417 2.5,3.417 2.5,3.417 2.667,3 true 2.885,3.01 2.969,3.344 2.969,3.344 3.052,3.344 true 2.771,2.49 3.021,2.156 3.021,2.156 3.104,2.156 true 2.74,2.667 3.073,2.667 true 5.323,1.583 5.49,1.583 5.49,1.583 5.656,2.083 true 5.219,1.76 5.385,1.76 5.385,1.76 5.552,2.094 true 5.365,3.167 5.531,3.167 5.531,3.167 5.615,2.667 true 6,2.083 6.25,1.75 6.25,1.75 6.333,1.75 true 5.833,2.083 6.083,1.5 6.083,1.5 6.167,1.5 true 0.385,0.292 0.604,0.5 0.219,0.208 10 false *1 3.917,0.313 4.115,0.5 0.198,0.188 10 false *2 2.26,1.5 2.438,1.688 0.177,0.188 10 false *3 2.01,1.719 2.208,1.906 0.198,0.188 10 false *4 2.135,2.969 2.313,3.177 0.177,0.208 10 false *5 2.167,3.323 2.344,3.521 0.177,0.198 10 false *6 3.094,3.24 3.271,3.438 0.177,0.198 10 false *7 3.125,2.052 3.302,2.24 0.177,0.188 10 false *8 2.042,2.406 2.219,2.594 0.177,0.188 10 false *3 3.094,2.563 3.271,2.771 0.177,0.208 10 false *5 5.146,1.469 5.323,1.677 0.177,0.208 10 false *5 5.052,1.667 5.229,1.875 0.177,0.208 10 false *5 5.188,3.063 5.365,3.26 0.177,0.198 10 false *6 6.208,1.396 6.385,1.594 0.177,0.198 10 false *7 6.365,1.646 6.542,1.833 0.177,0.188 10 false *8
*1 Planar Type Air-fuel Ratio Sensor *2 Cup Type Heated Oxygen Sensor
*3 Alumina *4 Dilation Layer
*5 Platinum Electrode *6 Sensor Element (Zirconia)
*7 Heater *8 Atmosphere


Warm-up Specification
Sensor Type Planar Type Cup Type
Warm-up Time Approx. 10 sec. Approx. 30 sec.



h.

Intake Air Control Valve

i.

The intake air control valve, which is provided in the intake air chamber, opens and closes to change the effective length of the intake manifold in 2 stages.

W135304C01
2.417,0.333 2.75,0.333 2.75,0.333 3.167,0.917 true 1.75,1.917 2.083,1.917 2.083,1.917 2.5,1.417 true 2.24,0.229 2.458,0.427 0.219,0.198 10 false *1 1.583,1.813 1.76,2 0.177,0.188 10 false *2
*1 Intake Air Control Valve *2 Actuator




i.

Actuator (Motor)

i.

The actuator activates the intake air control valve based on signals from the engine ECU.



j.

Ignition Coil

i.

The DIS provides 6 ignition coils, one for each cylinder. The spark plug cap, which provides contact to the spark plug, is integrated with an ignition coil. Also, an igniter is enclosed to simplify the system.

W135294C01
3.667,0.781 4.083,0.365 4.083,0.365 4.333,0.365 true 3.083,1.417 3.583,1.417 true 3.667,1.833 4.083,1.583 4.083,1.583 4.333,1.583 true 3.698,2 4.031,2.25 4.031,2.25 4.281,2.25 true 2.969,3.083 3.469,3.083 true 4.354,0.26 4.552,0.458 0.198,0.198 10 false *1 2.906,1.323 3.104,1.531 0.198,0.208 10 false *2 4.365,1.49 4.573,1.667 0.208,0.177 10 false *3 4.323,2.156 4.51,2.333 0.188,0.177 10 false *4 2.781,2.99 2.979,3.188 0.198,0.198 10 false *5
*1 Igniter *2 Iron Core
*3 Secondary Coil *4 Primary Coil
*5 Plug Cap - -




k.

Spark Plug

i.

Long-reach type spark plugs are used. This type of spark plugs allow the area of the cylinder head to receive the spark plugs to be made thick. Thus, the water jacket can be extended near the combustion chamber, which contributes to cooling performance.


ii.

Iridium-tipped spark plugs are used to achieve a 193,000 km (120,000 miles) maintenance interval. By making the center electrode of iridium, the superior ignition performance as platinum-tipped spark plugs is achieved and durability has been increased.

W135295C01
2.083,2.083 2.583,2.083 true 2.073,2.26 2.073,2.677 true 3.833,4.083 3.583,4.583 3.583,4.583 3.333,4.583 true 4.667,4.083 4.833,4.583 4.833,4.583 5.167,4.583 true 2.625,1.979 2.833,2.177 0.208,0.198 10 false *1 2.01,2.708 2.208,2.948 0.198,0.24 10 false *2 3.615,2.396 3.802,2.604 0.188,0.208 10 false *a 4.76,2.396 4.958,2.583 0.198,0.188 10 false *b 3.146,4.479 3.333,4.677 0.188,0.198 10 false *c 5.198,4.479 5.385,4.677 0.188,0.198 10 false *c
*1 Iridium Tip *2 Platinum Tip
*a Long-reach Type *b Conventional Type
*c Water Jacket - -





OPERATION


a.

ETCS-i (Electronic Throttle Control System-intelligent)

i.

The ETCS-i consists of the following five functions:

·

Normal Throttle Control (Non-linear Control)

·

Idle Speed Control

·

TRC (Traction Control)

·

VSC (Vehicle Stability Control)

·

Cruise Control*

*: Models with cruise control system



ii.

Normal Throttle Control (Non-linear Control)

1.

The engine ECU controls the throttle to an optimal throttle valve angle that is appropriate for the driving condition such as the amount of the accelerator pedal effort and the engine speed in order to realize excellent throttle control and comfort in all operating ranges.

Control Examples during Acceleration and Deceleration
W100289E46
5.5,0.333 6.667,0.688 1.167,0.354 10 false : With Control 5.49,0.698 6.625,1.073 1.135,0.375 10 false : Without Control 0.875,1.125 1.781,1.729 0.906,0.604 10 false Vehicle's Longitudinal G 0.854,2.417 1.802,3.042 0.948,0.625 10 false Throttle Valve Opening Angle 0.875,3.521 1.99,4.313 1.115,0.792 10 false Accelerator Pedal Depressed Angle 5.052,4.24 5.406,4.583 0.354,0.344 10 false Time 1.979,1.688 2.115,1.896 0.135,0.208 10 false 0 1.969,2.979 2.104,3.188 0.135,0.208 10 false 0 1.969,4.073 2.104,4.281 0.135,0.208 10 false 0



iii.

Idle Speed Control

1.

The engine ECU controls the throttle valve in order to constantly maintain an ideal idle speed.



iv.

TRC Throttle Control

1.

As part of the TRC system, the throttle valve is closed by a demand signal from the skid control ECU if an excessive amount of slippage is created at a driving wheel, thus facilitates the vehicle in ensuring excellent vehicle stability and driving force.



v.

VSC Coordination Control

1.

In order to bring the effectiveness of the VSC system control into full play, the throttle valve angle is controlled by effecting a coordination control with the skid control ECU.



vi.

Cruise Control (Models with Cruise Control System)

1.

An engine ECU with an integrated cruise control ECU directly actuates the throttle valve for operation of the cruise control.




b.

Dual VVT-i (Variable Valve Timing-intelligent) System

i.

Using the engine speed signal, vehicle speed signal, and the signals from air flow meter, throttle position sensor and water temperature sensor, the engine ECU calculates optimal valve timing for each driving condition and controls the camshaft timing oil control valve. In addition, the engine ECU uses signals from the camshaft position sensor and the crankshaft position sensor to detect the actual valve timing, thus providing feedback control to achieve the target valve timing.

W135217E01
0.74,0.458 2.448,0.698 1.708,0.24 10 false Crankshaft Position Sensor 1.115,0.844 2.063,1.052 0.948,0.208 10 false Air Flow Meter 0.792,1.198 2.344,1.417 1.552,0.219 10 false Throttle Position Sensor 0.74,1.573 2.469,1.781 1.729,0.208 10 false Water Temperature Sensor 0.719,1.969 2.427,2.146 1.708,0.177 8 false Intake and Exhaust VVT Sensors 0.875,2.323 2.281,2.521 1.406,0.198 10 false Vehicle Speed Signal 4.01,0.052 4.854,0.302 0.844,0.25 10 false Engine ECU 3.771,0.542 5.094,0.771 1.323,0.229 10 false Target Valve Timing 4.135,1.573 4.854,1.792 0.719,0.219 10 false Correction 3.833,1.969 5.125,2.198 1.292,0.229 10 false Actual Valve Timing 4.854,1.229 5.573,1.469 0.719,0.24 10 false Feedback 5.563,0.667 6.281,1.052 0.719,0.385 10 true Duty-cycle Control 6.521,0.365 7.083,1.042 0.563,0.677 8 false Camshaft Timing Oil Control Valve


ii.

Advance

1.

When the camshaft timing oil control valve is positioned as illustrated below by the advance signals from the engine ECU, the resultant oil pressure is applied to the timing advance side vane chamber to rotate the camshaft in the timing advance direction.

Intake Side
W135262C01
0.333,1.417 0.5,1.417 0.5,1.417 0.583,1.917 true 4.823,3.083 5.323,3.083 true 0.448,2.958 0.615,2.958 0.615,2.958 0.75,2.542 true 0.167,1.323 0.365,1.51 0.198,0.188 10 false *1 6.542,1.521 6.729,1.708 0.188,0.188 10 false *2 0.271,2.854 0.469,3.052 0.198,0.198 10 false *a 4.646,2.969 4.854,3.156 0.208,0.188 10 false *b 5.271,3.135 5.458,3.323 0.188,0.188 10 false *c 5.51,3.135 5.698,3.323 0.188,0.188 10 false *d
*1 Vane *2 Engine ECU
*a Rotational Direction *b Oil Pressure
*c IN *d Drain


Exhaust Side
W135269C01
0.5,1.083 0.667,1.083 0.667,1.083 0.917,1.583 true 0.417,3.25 0.583,3.25 0.583,3.25 1,2.583 true 5.563,3.25 6.146,3.25 true 0.323,0.979 0.521,1.188 0.198,0.208 10 false *1 3.885,2.177 4.063,2.354 0.177,0.177 10 false *2 0.25,3.125 0.438,3.354 0.188,0.229 10 false *a 5.365,3.146 5.552,3.354 0.188,0.208 10 false *b 6.083,3.333 6.271,3.542 0.188,0.208 10 false *c 6.354,3.333 6.542,3.521 0.188,0.188 10 false *d
*1 Vane *2 Engine ECU
*a Rotational Direction *b Oil Pressure
*c IN *d Drain




iii.

Retard

1.

When the camshaft timing oil control valve is positioned as illustrated below by the retard signals from the engine ECU, the resultant oil pressure is applied to the timing retard side vane chamber to rotate the camshaft in the timing retard direction.

Intake Side
W135263C01
0.5,1.25 0.667,1.25 0.667,1.25 0.75,1.667 true 0.833,3.25 1,3.25 1,3.25 1.083,2.5 true 5.333,3 5.583,3 true 0.667,3.167 0.844,3.365 0.177,0.198 10 false *1 6.552,1.469 6.74,1.646 0.188,0.177 10 false *2 0.313,1.146 0.521,1.354 0.208,0.208 10 false *a 4.99,3.104 5.188,3.281 0.198,0.177 10 false *b 5.271,3.104 5.448,3.313 0.177,0.208 10 false *c 5.615,2.906 5.813,3.104 0.198,0.198 10 false *d
*1 Vane *2 Engine ECU
*a Rotational Direction *b Drain
*c IN *d Oil Pressure


Exhaust Side
W135270C01
0.583,1 0.75,1 0.75,1 1,1.583 true 0.5,3 0.667,3 0.667,3 0.833,2.25 true 6.167,3.25 6.583,3.25 true 0.313,2.896 0.521,3.115 0.208,0.219 10 false *1 3.906,2.167 4.104,2.365 0.198,0.198 10 false *2 0.396,0.885 0.604,1.104 0.208,0.219 10 false *a 5.781,3.333 5.99,3.531 0.208,0.198 10 false *b 6.083,3.323 6.271,3.5 0.188,0.177 10 false *c 6.615,3.135 6.823,3.344 0.208,0.208 10 false *d
*1 Vane *2 Engine ECU
*a Rotational Direction *b Drain
*c IN *d Oil Pressure




iv.

Hold

1.

After reaching the target timing, the valve timing is held by keeping the camshaft timing oil control valve in the neutral position unless the traveling state changes.This adjusts the valve timing at the desired target position and prevents the engine oil from running out when it is unnecessary.




c.

ACIS (Acoustic Control Induction System)

i.

While the engine is running at middle speed under high load, the engine ECU controls the actuator to close the intake air control valve. As a result, the effective length of the intake manifold is lengthened and the intake efficiency, in the medium speed range, is improved due to the dynamic effect of the intake air, thereby increasing power output.

When the Intake Air Control Valve Closes
W135305E01
1.083,1.042 1.917,0.208 1.917,0.208 2.135,0.208 true 5.823,0.177 5.479,0.177 5.479,0.177 4.656,0.615 true 0.854,2.281 2.958,2.531 2.104,0.25 10 false : Effective Intake Manifold Length 2.167,0.115 3.26,0.563 1.094,0.448 10 false Intake Air Control Valve (Close) 5.917,0.073 7.021,0.51 1.104,0.438 10 false Intake Air Control Valve Close 3.927,0.375 4.313,0.604 0.385,0.229 10 false Open 3.708,0.99 4.208,1.396 0.5,0.406 10 false Throttle Valve 3.906,2 4.292,2.229 0.385,0.229 10 false Close 4.688,2.208 4.979,2.438 0.292,0.229 10 false Low 6.323,2.219 6.646,2.448 0.323,0.229 10 false High 5.115,2.438 6.094,2.635 0.979,0.198 10 false Engine Speed


ii.

Under any condition except when the engine is running at middle speed under high load, the engine ECU controls the actuator to open the intake air control valve. When the intake air control valve is open, the effective length of the intake manifold is shortened and the peak intake efficiency is shifted to the low-to-high engine speed range, thus providing greater output at low-to-high engine speeds.

When the Intake Air Control Valve Opens
W135306E01
1,0.865 1.333,1.865 1.333,1.865 1.5,1.865 true 5.917,0.167 6.083,0.167 6.083,0.167 6.25,0.417 true 1.563,1.771 3.531,2.031 1.969,0.26 10 false Intake Air Control Valve (Open) 0.854,2.104 2.958,2.333 2.104,0.229 10 false : Effective Intake Manifold Length 0.854,2.458 3.198,2.656 2.344,0.198 10 false : Effective Intake Air Chamber Length 4.052,0.052 5.885,0.25 1.833,0.198 10 false Intake Air Control Valve Open 3.917,0.406 4.292,0.646 0.375,0.24 10 false Open 3.698,0.865 4.198,1.229 0.5,0.365 10 false Throttle Valve 3.938,1.708 4.333,1.927 0.396,0.219 10 false Close 4.625,2.042 4.938,2.26 0.313,0.219 10 false Low 6.167,2.042 6.479,2.26 0.313,0.219 10 false High 5.083,2.302 6.052,2.552 0.969,0.25 10 false Engine Speed



d.

Fuel Pump Control

i.

A fuel pump control is used to stop the fuel pump when the airbag is deployed at the front collision. In this system, the airbag deployment signal from the airbag sensor assembly is detected by the engine ECU, which turns OFF the circuit opening relay. After the fuel pump control has been activated, turning the ignition switch (engine switch*) from OFF to ON (IG) cancels the fuel pump control, and the engine can be restarted.

*: Models with Smart Entry & Start System

W135196E01
6.125,1.552 6.302,1.552 6.302,1.552 6.396,1.229 true 0.76,0.823 1.573,1.51 0.813,0.688 10 false Front Airbag Sensor (RH and LH) 2.563,0.844 3.219,1.469 0.656,0.625 10 false Airbag Sensor Assembly 4.177,0.938 4.677,1.385 0.5,0.448 10 false Engine ECU 0.635,2.375 1.615,2.917 0.979,0.542 10 false Curtain Shield Airbag Sensor* (RH and LH) 2.625,2.417 3.448,3.083 0.823,0.667 10 false Side Airbag Sensor* (RH or LH) 5.115,1.427 6.104,1.958 0.99,0.531 10 false Circuit Opening Relay 6.615,1.833 7.031,2.448 0.417,0.615 10 false Fuel Pump Motor 0.969,3.375 1.927,3.635 0.958,0.26 10 false : CAN (V Bus) 3.979,3.229 6.427,3.656 2.448,0.427 10 false *: Models with Driver, Front Passenger, Side and Curtain Shield Airbags



e.

Cooling Fan Control System

i.

A cooling fan control system is used. To achieve an optimal fan speed in accordance with the water temperature, vehicle speed, engine speed, and air conditioner operating conditions, the engine ECU calculates the proper fan speed and proper fan speed control signals to the cooling fan ECU. Upon receiving the signals from the engine ECU, the cooling fan ECU actuates the fan motors.

W135235E01
0.531,0.365 2.219,0.656 1.688,0.292 10 false Water Temperature Sensor 0.542,1.188 2.271,1.448 1.729,0.26 10 false Crankshaft Position Sensor 0.771,1.979 2.01,2.24 1.24,0.26 10 false Combination Meter 0.677,2.448 2.063,2.688 1.385,0.24 10 false Vehicle Speed Signal 3.448,1.417 4.292,1.635 0.844,0.219 10 false Engine ECU 4.031,2.865 4.906,3.115 0.875,0.25 10 false CAN (V Bus) 3.24,3.281 4.573,3.5 1.333,0.219 10 false Air Conditioner ECU 5.51,0.635 6.115,1.219 0.604,0.583 10 false Cooling Fan ECU No. 1 5.51,1.948 6.115,2.531 0.604,0.583 10 false Cooling Fan ECU No. 2 6.313,0.198 6.99,0.552 0.677,0.354 10 false Fan Motor No. 1 6.323,1.51 7,1.865 0.677,0.354 10 false Fan Motor No. 2


ii.

As illustrated below, the engine ECU determines the required fan speed by selecting the fastest fan speed from among the following:

(A) Fan speed required by the water temperature

(B) Fan speed required by the air conditioner refrigerant pressure

(C) Fan speed required by the engine speed

(D) Fan speed required by the vehicle speed

(A) Fan speed required by water temperature
W135254E01
2.406,0.719 2.844,1.177 0.438,0.458 10 false Fan Speed 2.99,1.375 4.25,1.625 1.26,0.25 10 false Water Temperature

(B) Fan speed required by air conditioner refrigerant pressure
W135255E01
2.396,0.74 2.844,1.177 0.448,0.438 10 false Fan Speed 2.969,1.427 4.281,1.656 1.313,0.229 10 false Refrigerant Pressure

(C) Fan speed required by engine speed
W135256E01
2.406,0.75 2.875,1.146 0.469,0.396 10 false Fan Speed 3.125,1.427 4.063,1.646 0.938,0.219 10 false Engine Speed

(D) Fan speed required by vehicle speed
W135257E01
2.438,0.75 2.875,1.167 0.438,0.417 10 false Fan Speed 3.094,1.385 4.104,1.594 1.01,0.208 10 false Vehicle Speed




f.

Starter Control (Models with Smart Entry & Start System)

i.

Once the engine switch is pushed, this function continues to operate the starter until the engine starts, provided that the brake pedal pressed. This prevents starting failures and the engine from being cranked after the engine has started.


ii.

When the engine ECU detects a start signal from the main body ECU, this system monitors the engine speed (NE) signal and continues to operate the starter until it determines that the engine has started. Furthermore, even if the engine ECU detects a start signal from the main body ECU, this system will not operate the starter if the engine ECU has determined that the engine has already started.


iii.

If the starter relay (STAR) signal cannot be output because the power supplied to the engine ECU is low, the main body ECU outputs the starter relay (STAR) signal instead to help actuate the starter.

W135253E01
1.417,0.667 1.75,0.854 0.333,0.188 8 false PUSH 0.792,1.396 1.719,1.615 0.927,0.219 10 false Engine Switch 0.865,2.625 1.656,2.844 0.792,0.219 10 false Brake Pedal 2.302,0.875 3.354,1.104 1.052,0.229 10 false Main Body ECU 2.792,1.677 3.167,1.906 0.375,0.229 10 false STP 2.615,2.406 3.333,2.646 0.719,0.24 10 false ACC Relay 3.823,1.865 4,2.063 0.177,0.198 10 false IG 5.625,0.313 6.448,0.531 0.823,0.219 10 false Engine ECU 5.552,0.594 6.021,0.792 0.469,0.198 10 false STSW 5.552,0.771 6.021,0.969 0.469,0.198 10 false ACCR 5.552,0.969 6.021,1.167 0.469,0.198 10 false STAR 4.677,2.313 5.146,2.729 0.469,0.417 10 false ST Cut Relay 5.552,4.115 6.021,4.313 0.469,0.198 10 false STA 4.688,3.469 5.458,3.906 0.771,0.438 9 false Neutral Start Switch 4.708,4.552 5.135,4.958 0.427,0.406 9 false Starter Relay 1.625,3.667 2.073,3.854 0.448,0.188 9 false Starter 0.792,4.635 1.24,4.823 0.448,0.188 9 false Battery 5.49,4.875 6.896,5.104 1.406,0.229 10 false - Engine Speed Signal 5.49,5.042 6.781,5.438 1.292,0.396 10 false - Water Temperature Signal


iv.

As indicated in the following timing chart, when the engine ECU detects a start signal (STSW) from the main body ECU, the engine ECU outputs the STAR and ACCR signals to the main body ECU. Upon detecting the STAR and ACCR signals from the engine ECU, the main body ECU energizes the starter relay to operate the starter. If the engine is already running, the engine ECU stops the output of the STAR and ACCR signals to the main body ECU. Thus, the main body ECU will not energize the starter relay.


v.

After the starter operates and the engine speed becomes higher than approximately 500 rpm, the engine ECU determines that the engine has started and stops the output of the STAR and ACCR signals to the main body ECU. Thus, the main body ECU will stop the operation of the starter.


vi.

If the engine has any failure and does not work, the starter operates as long as its maximum continuous operation time and stops automatically. The maximum continuous operation time is approximately 2 seconds through 25 seconds depending on the water temperature condition. When the water temperature is extremely low, it is approximately 25 seconds and when the engine is warmed up sufficiently, it is approximately 2 seconds.


vii.

This system cuts off the current that powers the accessories while the engine is cranking to prevent the accessory illumination from operating intermittently due to the unstable voltage that is associated with the cranking of the engine.


viii.

This system has the following protections.

·

While the engine is running normally, the starter does not operate.

·

In case the driver keeps pressing the engine switch and the engine successfully started, the engine ECU stops the output of the STAR and ACCR signals when the engine speed becomes higher than 1,200 rpm. Thus, the main body ECU will stop the operation of the starter.

·

In case the driver keeps pressing the engine switch and the engine does not start, the engine ECU stops the output of the STAR and ACCR signals after 30 seconds have elapsed. Thus, the main body ECU will stop the operation of the starter.

·

In case the engine ECU cannot detect an engine speed signal while the starter is operating, the engine ECU will immediately stop the output of the STAR and ACCR signals. Thus, the main body ECU will stop the operation of the starter.

Timing Chart
W135198E01
0.063,3.563 6.073,3.781 6.01,0.219 8 false *a: Engine ECU determines that the engine has started successfully when the engine speed is approximately 500 rpm. 4.094,2.719 4.281,2.917 0.188,0.198 9 false *a 2.906,0.844 3.99,1.219 1.083,0.375 8 false Cranking Limit Approx. 2 to 25 sec. 1.573,0.344 1.833,0.542 0.26,0.198 10 false ON 1.49,1.604 1.802,1.823 0.313,0.219 10 false OFF 1.49,0.698 1.802,0.917 0.313,0.219 10 false OFF 1.49,2.24 1.802,2.458 0.313,0.219 10 false OFF 0.458,0.583 1.25,0.833 0.792,0.25 10 false Start Signal 1.563,1.229 1.823,1.427 0.26,0.198 10 false ON 1.563,1.844 1.823,2.042 0.26,0.198 10 false ON 0.375,1.406 1.24,1.667 0.865,0.26 10 false Starter Relay 0.167,2.01 1.302,2.26 1.135,0.25 10 false Accessory Power 0.188,3.188 1.802,3.427 1.615,0.24 10 false Engine Speed Signal (NE) 5.156,2.406 6.406,2.813 1.25,0.406 10 false Successful Starting of Engine 5.177,3.125 6.271,3.469 1.094,0.344 10 false Failed Starting of Engine





FAIL-SAFE


a.

When a malfunction is detected by any of the sensors, there is a possibility of an engine or another malfunction occurring if the engine ECU were to continue to control the engine control system in the normal way. To prevent such a problem, the fail-safe function of the engine ECU either relies on the data stored in memory to allow the engine control system to continue operating, or stops the engine if a hazard is anticipated. For details, refer to the Repair Manual.


b.

Fail-safe of Accelerator Pedal Position Sensor

i.

The accelerator pedal position sensor is comprised of two (main, sub) sensor circuits. If a malfunction occurs in either one of the sensor circuits, the engine ECU detects the abnormal signal by voltage difference between these two sensor circuits and switches to the limp mode. In the limp mode, the remaining circuit is used to calculate the accelerator pedal depressed angle, in order to operate the vehicle under the limp mode control.

W135204E01
1.99,1.75 2.073,1.75 2.073,1.75 2.073,2 true 2.083,3 2.167,3 2.167,3 2.25,2.333 true 5.188,2.594 5.188,2.51 5.188,2.51 4.854,2.094 true 3.156,0.719 3.979,0.958 0.823,0.24 10 false Engine ECU 1.021,1.677 1.979,2 0.958,0.323 8 false Accelerator Pedal Position Sensor 1.125,2.896 2.073,3.219 0.948,0.323 8 false Accelerator Pedal Position Sensor 1.604,2.167 1.896,2.344 0.292,0.177 8 false Main 2.396,2.323 2.688,2.5 0.292,0.177 8 false Sub 3.198,2.281 3.49,2.458 0.292,0.177 8 false Main 3.219,2.458 3.51,2.635 0.292,0.177 8 false Sub 3.969,1.75 4.365,1.958 0.396,0.208 10 false Open 3.75,2.656 4.573,2.875 0.823,0.219 9 false Throttle Valve 3.042,2.625 3.552,3.156 0.51,0.531 9 false Throttle Position Sensor 5.021,2.615 5.427,2.969 0.406,0.354 8 false Return Spring 5.594,2.563 6.073,3.073 0.479,0.51 9 false Throttle Control Motor 1.281,3.25 2.427,3.469 1.146,0.219 10 false Accelerator Pedal 4.115,3.24 5.021,3.5 0.906,0.26 10 false Throttle Body


ii.

If both circuits have a malfunction, the engine ECU detects the abnormal signal by voltage from these two sensor circuits and stops the throttle control. At this time, the vehicle can be driven within its idling range.

W135205E01
2,1.75 2.083,1.75 2.083,1.75 2.083,2 true 2,2.969 2.083,2.969 2.083,2.969 2.25,2.302 true 4.896,2.146 5.063,2.479 5.063,2.479 5.063,2.646 true 3.188,0.719 4.01,0.938 0.823,0.219 10 false Engine ECU 1.021,1.677 1.969,2.042 0.948,0.365 8 false Accelerator Pedal Position Sensor 1.031,2.896 1.979,3.26 0.948,0.365 8 false Accelerator Pedal Position Sensor 1.635,2.167 1.906,2.375 0.271,0.208 8 false Main 2.427,2.281 2.698,2.49 0.271,0.208 8 false Sub 3.208,2.271 3.479,2.479 0.271,0.208 8 false Main 3.229,2.438 3.5,2.646 0.271,0.208 8 false Sub 3.719,1.656 4.563,2.031 0.844,0.375 8 false Close by Return Spring 3.094,2.625 3.531,3.125 0.438,0.5 8 false Throttle Position Sensor 3.781,2.677 4.521,2.896 0.74,0.219 8 false Throttle Valve 4.917,2.677 5.302,3.063 0.385,0.385 8 false Return Spring 5.635,2.552 6.063,3.063 0.427,0.51 8 false Throttle Control Motor 1.281,3.24 2.469,3.448 1.188,0.208 10 false Accelerator Pedal 4,3.24 4.875,3.49 0.875,0.25 10 false Throttle Body



c.

Fail-safe of Throttle Position Sensor

i.

The throttle position sensor is comprised of two (main, sub) sensor circuits. If a malfunction occurs in either one or both of the sensor circuits, the engine ECU detects the abnormal signal by voltage difference between these two sensor circuits, cuts off the current to the throttle control motor, and switches to the limp mode. Then, the force of the return spring causes the throttle valve to return and stay at the prescribed opening. At this time, the vehicle can be driven in the limp mode while the engine output is regulated through the control of the fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator opening.


ii.

The same control as above is effected if the engine ECU detects a malfunction in the throttle control motor system.

W135206E01
2,1.75 2.083,1.75 2.083,1.75 2.083,2 true 2,2.958 2.083,2.958 2.083,2.958 2.25,2.292 true 4.969,2.583 4.969,2.417 4.969,2.417 4.885,2.167 true 1.646,0.719 2.229,0.958 0.583,0.24 10 false Injectors 3.167,0.729 3.979,0.948 0.813,0.219 10 false Engine ECU 4.802,0.729 5.625,0.948 0.823,0.219 10 false Ignition Coils 1.031,1.667 1.979,1.99 0.948,0.323 8 false Accelerator Pedal Position Sensor 1.031,2.875 1.979,3.198 0.948,0.323 8 false Accelerator Pedal Position Sensor 1.615,2.125 1.906,2.302 0.292,0.177 8 false Main 2.427,2.271 2.719,2.438 0.292,0.167 8 false Sub 3.198,2.281 3.49,2.458 0.292,0.177 8 false Main 3.219,2.458 3.51,2.625 0.292,0.167 8 false Sub 3.75,1.698 4.531,2.031 0.781,0.333 7 false Return to Prescribed Angle 3.75,2.677 4.531,2.885 0.781,0.208 8 false Throttle Valve 4.813,2.604 5.198,2.979 0.385,0.375 8 false Return Spring 5.615,2.563 6.052,3.063 0.438,0.5 8 false Throttle Control Motor 4.01,3.24 4.896,3.5 0.885,0.26 10 false Throttle Body 1.313,3.25 2.458,3.469 1.146,0.219 10 false Accelerator Pedal




DIAGNOSIS


a.

When the engine ECU detects a malfunction, the engine ECU makes a diagnosis and memorizes the failed section. Furthermore, the check engine warning light in the combination meter illuminates or blinks to inform the driver.


b.

The engine ECU will also store the DTCs (Diagnostic Trouble Codes) of the malfunctions.


c.

The DTCs can be accessed by the use of the intelligent tester II.


d.

All the DTCs have been made to correspond to the SAE controlled codes. Some of the DTCs have been further divided into smaller detection areas than in the past, and new DTCs have been assigned to them. For details, refer to the Repair Manual.

HINT:

To clear the DTC that is stored in the engine ECU, use the intelligent tester II or disconnect the battery terminal or remove the EFI fuse for 1 minute or longer.