Home › Engine / Hybrid System › 2AZ-FE ENGINE MECHANICAL › ENGINE UNIT › from 2016.05
NM24M0E _51 Engine / Hybrid System _061720 2AZ-FE ENGINE MECHANICAL _0301072 ENGINE UNIT UN GENERAL/CONTROL/DETAILS F

2AZ-FE ENGINE MECHANICAL  ENGINE UNIT  GENERAL/CONTROL/DETAILS  GENERAL  


OUTLINE


a.

The 2AZ-FE engine is an in-line, 4-cylinder, 2.4-liter, 16-valve DOHC engine. This engine uses the VVT-i (Variable Valve Timing-intelligent) system, DIS (Direct Ignition System), ETCS-i (Electronic Throttle Control System-intelligent). It has been developed to realize high performance, quietness, fuel economy and clean emission.

W135227

W135228



MAJOR DIFFERENCE


a.

Emission regulation has been changed.



SPECIFICATIONS


*1: Emission regulations differ depending on the specifications of the vehicle.

*2: Weight shows the figure with oil and water fully filled.

Engine 2AZ-FE
No. of Cyls. & Arrangement 4-cylinder, In-line
Valve Mechanism 16-valve DOHC, Chain Drive
(With VVT-i)
Combustion Chamber Pentroof Type
Manifolds Cross-flow
Fuel System EFI
Ignition System DIS
Displacement cm3 (cu. in.) 2362 (144.2)
Bore X Stroke mm (in.) 88.5 x 96.0 (3.48 x 3.78)
Compression Ratio 9.8 : 1
Max. Output (EEC) kW@rpm 125@6000
Max. Torque (EEC) N*m@rpm 224@4000
Valve Timing Intake Open 3° to 43° BTDC
Close 65° to 25° ABDC
Exhaust Open 45° BBDC
Close 3° ATDC
Firing Order 1 - 3 - 4 - 2
Research Octane Number 91 or higher
Oil Grade API SL, SM, SN or ILSAC
Oil Capacity Dry Liters (US qts, Imp. qts) 5.0 (5.3, 4.4)
With Oil Filter Liters (US qts, Imp. qts) 4.3 (4.5, 3.8)
Without Oil Filter Liters (US qts, Imp. qts) 4.1 (3.8, 3.1)
Emission Regulation*1 EURO IV, EURO V+, EURO VIb
Engine Service Mass*2 (Reference) kg (lb) 129 (284.4)


MAIN FEATURES


a.

The 2AZ-FE engine has achieved the following performance through the use of the items listed below.

(1) High performance and reliability

(2) Low noise and vibration

(3) Lightweight and compact design

(4) Good serviceability

(5) Clean emissions and fuel economy

Section Item (1) (2) (3) (4) (5)
Engine Proper The cylinder block made of aluminum alloy along with the magnesium alloy die-cast cylinder head is used. ○
The taper squish shape is used for the combustion chamber. ○ ○
The resin gear balance shaft is used. ○ ○
Valve Mechanism The shim-less type valve lifters are used. ○ ○
The VVT-i system is used. ○ ○
Intake and Exhaust System The intake manifold made of plastic is used. ○
The linkless-type throttle body is used. ○ ○
The thin-wall ceramic TWC (Three-Way Catalytic converter) is used. ○
Fuel System The fuel returnless system is used. ○ ○ ○
The quick connectors are used to connect the fuel hose with the fuel pipe. ○ ○ ○
The 12-hole type fuel injectors with high atomizing performance are used. ○ ○
Ignition System The iridium-tipped spark plugs are used. ○ ○
Charging System The segment conductor type alternator is used. ○ ○ ○
Starting System The PS (Planetary reduction-Segment conductor motor) type starter is used. ○ ○
Engine Control System The ETCS-i is used. ○ ○
The DIS (Direct Ignition System) makes ignition timing adjustment unnecessary. ○ ○ ○
The non-contact type sensor is used in the throttle position sensor. ○
The planar type air-fuel ratio sensor is used. ○