Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2016.05
NM24M0E _53 Suspension _062306 TIRE PRESSURE MONITORING _0304135 TIRE PRESSURE WARNING SYSTEM UN GENERAL/CONTROL/DETAILS F

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS



Component Outline
Combination Meter Assembly
·

Tire Pressure Warning Light


·

Sends a vehicle speed signal to the tire pressure warning ECU and receiver.

·

Illuminates or stays on after blinking for 1 minute to warn the driver in accordance with the signal from the tire pressure warning system.

·

Flashes 3 times after initialization.


Tire Pressure Warning Reset Switch
·

The warning threshold is calculated from the tire inflation pressure value at the time of initialization and memorized in the tire pressure warning ECU and receiver by operating the tire pressure warning reset switch.

·

Selects the wheel set.


Tire Pressure Warning Valve and Transmitter Detects the tire pressure, internal temperature and rotational acceleration of the tire, and transmits the measured values and the ID code to the tire pressure warning ECU and receiver.
Tire Pressure Warning ECU and Receiver Receives the data from the tire pressure warning valve and transmitter and monitors the tire inflation pressure.
Outputs the respective signal to the combination meter assembly when a drop in the tire inflation pressure, a system malfunction or the beginning of initialization is detected.

FUNCTION


a.

Warning Function

i.

When any of the following conditions are met, the tire pressure warning system illuminates the tire pressure warning light to warn the driver.

Warning Condition
·

When the tire pressure decreases to approximately 80% or less of the default tire pressure set during system initialization.

·

When the tire pressure decreases rapidly (approximately 20 kPa or more over a period of several minutes) and drops below approximately 80% or less of the tire pressure when warm.


Service Tip

When driving for a certain period of time after the system has been initialized, the system corrects the tire pressure set during initialization according to the vehicle driving conditions and sets the tire pressure when warm.

X136108E01
3.063,2.875 3.479,1.958 3.479,1.958 3.646,1.958 true 5.313,3.542 5.479,2.594 5.479,2.594 5.646,2.594 true 0.875,0.969 3.167,1.167 2.292,0.198 10 false (Tire Pressure) 0.313,1.531 2.604,1.729 2.292,0.198 10 false Tire Pressure when Warm 0.385,2.094 1.885,2.521 1.5,0.427 10 false Tire Pressure Set during Initialization 0.573,2.698 1.885,3.135 1.313,0.438 10 false 80% of Tire Pressure when Warm 0.344,3.344 1.906,3.833 1.563,0.49 10 false 80% of Tire Pressure Set during Initialization 4.885,0.51 6.656,0.729 1.771,0.219 10 false : Tire Pressure (Normal) 4.885,0.906 6.948,1.229 2.063,0.323 10 false : Tire Pressure (Rapid Decrease) 3.75,1.885 6.74,2.156 2.99,0.271 10 false Illuminates the Tire Pressure Warning Light 5.74,2.51 6.927,3.281 1.188,0.771 10 false Illuminates the Tire Pressure Warning Light



ii.

The tire pressure warning system has 2 warning methods which are used depending on the condition detected.


iii.

The table below shows the warning methods for the tire pressure warning light in the combination meter assembly:

Detection Condition Tire Pressure Warning Light

*1: If the tire pressure warning light illuminates, adjust the tire pressure.

*2: If the tire pressure warning light stays on after blinking for 1 minute, the system is malfunctioning and must be repaired in order to turn off the light. For details, refer to the Repair Manual.

The tire pressure warning system has detected that the tire pressure has become lower than the warning threshold. Illuminates*1
The tire pressure warning system has detected a malfunction in the system. Illuminates after blinking for 1 minute*2



b.

Initial Check Function

i.

After the engine switch is tuned on (IG), the tire pressure warning ECU and receiver illuminates the tire pressure warning light for 3 seconds to check the warning light circuit.



c.

Initialization Function

i.

The warning threshold is calculated from the tire inflation pressure valve at the time of initialization and memorized in the tire pressure warning ECU and receiver. Therefore, the tire pressure warning ECU and receiver should be initialized after:

·

The recommended tire inflation pressure changes due to changes in vehicle weight, speed conditions or tire size.

·

Tire pressure warning ECU and receiver or the tire pressure warning valve and transmitter are replaced.

·

The tires are rotated on a vehicle with different recommended tire inflation pressures for the front and rear tires.

·

The tire pressure is adjusted.



ii.

Initialization starts after the tire pressure warning reset switch is pressed and held (with the engine switch on (IG) and with the vehicle stopped) and the tire pressure warning light blinks slowly 3 times.


iii.

Before performing initialization, adjust the tire inflation pressure to the recommended pressure when the tires are cold. For details, refer to the Repair Manual.




CONSTRUCTION AND OPERATION


a.

Tire Pressure Warning Valve and Transmitter

i.

The tire pressure warning valve and transmitters are integrated into the tire valves. Each transmitter consists of a lithium battery, sensor and transmitter.


ii.

Make sure not to damage the urethane covered backside of the transmitter (the surface opposite to the side with the ID code) with anything sharp.


iii.

The transmitter directly measures tire inflation pressure and temperature to see if the vehicle can continue to run.


iv.

The transmitter transmits the measured tire inflation pressure and temperature values to the tire pressure warning ECU and receiver on a frequency of 315 MHz*1, or 433 MHz*2.

HINT:
·

*1: Models for Taiwan

·

*2: Models for G.C.C. countries




v.

Depending on the timing of the data transmission, it may take several minutes to receive the data from the tire pressure warning valve and transmitter.


vi.

The ID code is written on the tire pressure warning valve and transmitter.

X136109E01
1.333,0.75 1.417,0.167 1.417,0.167 1.583,0.167 true 1.667,1.083 1.75,0.417 1.75,0.417 1.917,0.417 true 2.031,1.521 2.208,0.667 2.208,0.667 2.375,0.667 true 2.135,1.625 2.417,0.917 2.417,0.917 2.583,0.917 true 2.292,1.823 2.625,1.156 2.625,1.156 2.792,1.156 true 1.938,2.458 2.104,2.458 2.104,2.458 2.375,1.948 true 4.396,1.917 4.542,2.552 4.542,2.552 4.74,2.552 true 3.573,2.448 3.74,2.448 3.74,2.448 3.813,1.917 true 6.073,0.125 6.24,0.125 6.24,0.125 6.26,1.677 true 0.99,2.375 3.281,2.573 2.292,0.198 10 false Tire Valve Cap 1.667,0.083 5.25,0.292 3.583,0.208 10 false Tire Pressure Warning Valve and Transmitter 1.99,0.333 4.281,0.531 2.292,0.198 10 false Grommet 2.448,0.583 4.74,0.781 2.292,0.198 10 false Washer 2.875,1.073 5.167,1.271 2.292,0.198 10 false Tire Valve Core 2.667,0.833 4.958,1.031 2.292,0.198 10 false Nut 2.615,2.354 3.906,2.625 1.292,0.271 10 false Lithium Battery 4.813,2.469 7.104,2.667 2.292,0.198 10 false Sensor and Transmitter 4.656,0.052 6.042,0.458 1.385,0.406 10 false ID Code (Hexadecimal 7 Digits)

Service Tip
·

The lithium batteries of the tire pressure warning valve and transmitters are non-replaceable. If the battery is depleted, the tire pressure warning valve and transmitter must be replaced (battery life: approximately 10 years).

·

A new tire pressure warning valve and transmitter is shipped in sleep mode to prevent the battery from depleting in storage. When the tire inflation pressure in the detection portion of the tire pressure warning valve and transmitter increases or decreases by 40 kPa (0.4 kgf/cm2, 0.4 bar) within 30 seconds, the tire pressure warning valve and transmitter automatically cancels sleep mode. Once sleep mode is canceled, the tire pressure warning valve and transmitter cannot return to sleep mode.

·

When replacing a tire pressure warning valve and transmitter, each of the tire pressure warning valve and transmitter ID codes must be registered. If even one of the tire pressure warning valve and transmitters is replaced, the ID codes of all tire pressure warning valve and transmitters must be registered again. Record all existing ID codes before beginning the process to enter new ID codes.

·

To register an ID code, use the Global TechStream (GTS) to enter the ID code that is indicated on the tire pressure warning valve and transmitter.

·

Be careful not to damage the tire pressure warning valve and transmitters when removing and reinstalling them.

·

Replace the grommet and valve core with new ones when replacing or removing and reinstalling the tire pressure warning valve and transmitter. This is necessary to ensure sealing performance.

·

When replacing a valve cap, use only the specified cap. If an unspecified cap is used, it may seize to the tire pressure warning valve and transmitter.

·

For details, refer to the Repair Manual.





DIAGNOSIS


a.

To inform the driver when the tire pressure warning ECU and receiver detects a malfunction in the system, the tire pressure warning ECU and receiver will blink the tire pressure warning light for 1 minute, after which the light will stay on. It will also store the Diagnostic Trouble Codes (DTCs) in memory.


b.

5-digit DTCs can be read by connecting the Global TechStream (GTS) to the DLC3. For details, refer to the Repair Manual.