Home › Power Source / Network › NETWORKING › MULTIPLEX COMMUNICATION SYSTEM › from 2016.05
NM24M0E _57 Power Source / Network _061449 NETWORKING _0299867 MULTIPLEX COMMUNICATION SYSTEM UN GENERAL/CONTROL/DETAILS F

NETWORKING  MULTIPLEX COMMUNICATION SYSTEM  GENERAL/CONTROL/DETAILS  GENERAL  


OUTLINE


a.

The multiplex communication system of the new models uses 2 communication protocols described below in order to achieve a slimmer wiring harness configuration.


b.

Controller Area Network (CAN): There are 2 types, they are categorized based on the communication speed: High Speed (HS) CAN and Medium Speed (MS) CAN. The HS-CAN is used for the powertrain, chassis, and body electrical system, while the MS-CAN is used for the body electrical system.


c.

AVC-LAN (Audio Visual Communication - Local Area Network): It is used only when the vehicle is equipped with both a radio and player with display and a rear seat entertainment ECU.


d.

There are 2 CAN buses, the HS-CAN (CAN No. 1 bus) and MS-CAN (MS bus). The main body ECU has a gateway function and is used to connect the buses, thus enabling communication among the different buses.


e.

Along with the use of CAN in the power train, chassis, and body electrical system, the BEAN (Body Electronics Area Network) that was used in the body electrical system of the previous models has been discontinued.


f.

A customized body electronics system is used, enabling the control functions of the ECUs to be set using an intelligent tester II.


g.

Multiplex communication uses serial communication data that consists of bits and frames in order to exchange information among the various ECUs. This allows a reduction of the amount of wiring on the vehicle.

·

A bit is the basic unit of communication that is used to represent the information. A bit is represented by binary values of "0" or "1".

·

A frame is a body of data that is transmitted together. A frame contains a header that indicates the beginning, and an end message that indicates the end.

Y189214E01
3.271,0.458 4.042,0.656 0.771,0.198 10 false Frame 3.323,1.063 4.094,1.26 0.771,0.198 10 false Data 1.958,1.583 2.729,1.781 0.771,0.198 10 false Header 4.417,1.594 5.375,1.802 0.958,0.208 10 false End Message 2.792,2.417 4.531,2.635 1.74,0.219 10 false Serial Communication Data 1.375,0.865 1.594,1.073 0.219,0.208 10 false 1 1.385,1.302 1.604,1.51 0.219,0.208 10 false 0 1.906,3.219 2.677,3.417 0.771,0.198 10 false Switch 0.406,4.24 1.177,4.438 0.771,0.198 10 false Battery 2.615,4.24 3.052,4.438 0.438,0.198 10 false ECU 3.354,3.615 3.594,3.802 0.24,0.188 10 false On 3.823,3.615 4.063,3.802 0.24,0.188 10 false On 3.583,4.135 3.823,4.323 0.24,0.188 10 false Off 4.5,4.219 4.938,4.417 0.438,0.198 10 false ECU 6.115,3.479 6.552,3.677 0.438,0.198 10 false Light 6.135,3.969 6.573,4.167 0.438,0.198 10 false Motor 6.156,4.375 6.625,4.563 0.469,0.188 10 false Heater 6.167,4.813 6.771,5 0.604,0.188 10 false Solenoid



h.

DIFFERENCES AMONG CAN, AVC-LAN AND BEAN

i.

The protocols, which are the rules for establishing data communication, differ among the CAN, AVC-LAN and BEAN. If ECUs use different types of data such as with different communication speed, communication wire, and signals, they will be unable to understand each other. Therefore, protocols (rules) must be established among them.


ii.

One of the features of CAN is a faster communication speed than AVC-LAN and BEAN. Thus, it can transmit and receive a greater amount of data in a shorter time than the other protocols. This enables the accurate transmission and reception of data in the power train and chassis control system, which requires a great amount of data to be transmitted and received in a short time.

*: bps: abbreviation for "Bits Per Second", indicating the number of bits that can be transmitted per second.

Protocol CAN
(ISO Standard)
AVC-LAN
(TOYOTA Original)
BEAN
(TOYOTA Original)
Communication Speed 500 k bps*/HS-CAN
250 k bps*/MS-CAN
(Max. 1 Mbps)
Max. 17.8 kbps* Max. 10 kbps*
Communication Wire Twisted-pair Wire Twisted-pair Wire AV Single Wire
Drive Type Differential Voltage Drive Differential Voltage Drive Single Wire Voltage Drive
Data Length 1-8 Byte (Variable) 0-32 Byte (Variable) 1-11 Byte (Variable)



i.

Communication Wire

i.

A single, AV (Automobile Vinyl) wire is used for BEAN communication. A twisted-pair wire is used for CAN and AVC-LAN communication.

Communication Wire Outline
Twisted-pair Wire for CAN
Y209951

In this communication wire, a pair of lines are twisted together and covered with insulation. The communication is driven by applying positive (+) and negative (-) voltage to the two lines in order to send a single signal.
This system, which is called a "Differential Voltage Drive", can reduce noise.
Twisted-pair Wire for AVC-LAN
Y209961

AV Single Wire
Y209946

This is a lightweight single communication wire that consists of a single core line surrounded by insulation. Voltage is applied to this line in order to drive the communication, and this system is called a "Single Wire Voltage Drive".

Single Wire Voltage Drive
Y189216E01
2.104,1.802 2.563,2 0.458,0.198 10 false ECU 4.906,1.823 5.365,2.021 0.458,0.198 10 false ECU 3.25,2 4.271,2.208 1.021,0.208 10 false AV Single Wire

Differential Voltage Drive
Y189217E02
1.958,1.771 2.417,1.969 0.458,0.198 10 false ECU 4.906,1.781 5.365,1.979 0.458,0.198 10 false ECU 3.104,2.063 4.219,2.292 1.115,0.229 10 false Twisted-pair Wire 2.448,1.542 2.635,1.719 0.188,0.177 10 false + 2.448,2.042 2.635,2.219 0.188,0.177 10 false - 4.594,1.531 4.781,1.708 0.188,0.177 10 false - 4.583,2.031 4.771,2.208 0.188,0.177 10 false +




MAJOR DIFFERENCE


a.

The brake actuator assembly (skid control ECU) has been discontinued on models without VSC.